Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ref:tools119 [2018/03/04 00:04] hippysmack created |
techtalk:ref:tools119 [2018/05/21 07:55] ixl2relax [REF: Tools - Sub-019] |
||
---|---|---|---|
Line 1: | Line 1: | ||
[[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
- | ====== REF: Shop Notes, Tips, and Tools - Sub-03H ====== | + | ====== REF: Tools - 119 ====== |
====== Wheel Hub Bearing Locknut Wrench ====== | ====== Wheel Hub Bearing Locknut Wrench ====== | ||
- | |{{:techtalk:ref:notes:wheel_hub_bearing_locknut_wrench_1_by_dirtyharry68.jpg?direct&300|}}|{{:techtalk:ref:notes:wheel_hub_bearing_locknut_wrench_2_by_dirtyharry68.jpg?direct&300|}}|{{:techtalk:ref:notes:wheel_hub_bearing_locknut_wrench_3_by_dirtyharry68.jpg?direct&300|}}| | + | |{{techtalk:ref:tools:wheel_hub_bearing_locknut_wrench_1_by_dirtyharry68.jpg?direct&300|}}|{{techtalk:ref:tools:wheel_hub_bearing_locknut_wrench_2_by_dirtyharry68.jpg?direct&300|}}|{{techtalk:ref:tools:wheel_hub_bearing_locknut_wrench_3_by_dirtyharry68.jpg?direct&300|}}| |
- | |An old socket (ID larger than the sliding top hat \\ spacer) with most of the teeth hogged. Cut some \\ slots and made some little ears. ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?threadid=395586&page=19))|Cut a stepped bar in the lathe to fit the bearings. The \\ big end got pressed into the socket. The step sits \\ 3/16” below the business end of the socket. ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?threadid=395586&page=19))|Held it together with a hose clamp for welding. ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?threadid=395586&page=19))| | + | |An old socket (ID larger than the sliding top hat \\ spacer) with most of the teeth hogged. Cut some \\ slots and made some little ears. ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/forums/showthread.php?threadid=395586&page=19))|Cut a stepped bar in the lathe to fit the bearings. The \\ big end got pressed into the socket. The step sits \\ 3/16” below the business end of the socket. ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/forums/showthread.php?threadid=395586&page=19))|Held it together with a hose clamp for welding. ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/forums/showthread.php?threadid=395586&page=19))| |
- | |{{:techtalk:ref:notes:wheel_hub_bearing_locknut_wrench_4_by_dirtyharry68.jpg?direct&300|}} ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?threadid=395586&page=19))|{{:techtalk:ref:notes:wheel_hub_bearing_locknut_wrench_5_by_dirtyharry68.jpg?direct&300|}} ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/vbportal/forums/showthread.php?threadid=395586&page=19))| | + | |{{techtalk:ref:tools:wheel_hub_bearing_locknut_wrench_4_by_dirtyharry68.jpg?direct&300|}} ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/forums/showthread.php?threadid=395586&page=19))|{{techtalk:ref:tools:wheel_hub_bearing_locknut_wrench_5_by_dirtyharry68.jpg?direct&300|}} ((photo by DirtyHarry68 of the XLFORUM http://xlforum.net/forums/showthread.php?threadid=395586&page=19))| |
\\ | \\ |