Differences

This shows you the differences between two versions of the page.

--- techtalk:ref:engmech03k [2019/07/21 00:06]
hippysmack [Chopping OEM Sprocket Cover Into a Gothic Cross]
+++ techtalk:ref:engmech03k [2019/07/21 01:02] (current)
hippysmack [Chopping OEM Sprocket Cover Into a Gothic Cross]
@@ Line 12: / Line 12: @@
 \\
+Total of about 48 hours. \\
 Measurements taken with the graphic idea rough sketched. \\
@@ Line 31: / Line 32: @@
 Finish shaping and sanded with sandpaper and getting ready for the wrinkle paint. \\
+The cross portioned was masked off to keep paint from sticking to it. \\
 {{:techtalk:ref:engmech:sprocket_cover_mod_13_by_anachris.jpg?direct&300|}} {{:techtalk:ref:engmech:sprocket_cover_mod_14_by_anachris.jpg?direct&300|}} {{:techtalk:ref:engmech:sprocket_cover_mod_15_by_anachris.jpg?direct&200|}} \\
+The VHT wrinkle plus went on gloss (very gloss) with at least 3 coats at varying angles and given a couple of hours for the paint to set. \\
+Then it was heated in the oven at 200 degrees. \\
+For those using the VHT wrinkle paint, it takes a while to cure. \\
+It's very durable once it does finally finish gassing out. \\
+After about an hour in the oven, (this would be about 2 to 2-1/2 hours after first spray) a dental tool was used to remove the masking. \\
+This seemed to be a good time to pull tape very easily using the flat blade tool designed not to hurt enamel. \\
 {{:techtalk:ref:engmech:sprocket_cover_mod_16_by_anachris.jpg?direct&300|}} {{:techtalk:ref:engmech:sprocket_cover_mod_17_by_anachris.jpg?direct&300|}} {{:techtalk:ref:engmech:sprocket_cover_mod_18_by_anachris.jpg?direct&300|}} \\
-{{:techtalk:ref:engmech:sprocket_cover_mod_19_by_anachris.jpg?direct&300|}} {{:techtalk:ref:engmech:sprocket_cover_mod_20_by_anachris.jpg?direct&300|}} {{:techtalk:ref:engmech:sprocket_cover_mod_21_by_anachris.jpg?direct&300|}} \\
+After it finishes curing, wash the adheasive off with solvent then block sand with 1000 grit wet to blend all lines back to crisp. \\
+And finally, a bit of re-polish on the cross and fitted. \\
+{{:techtalk:ref:engmech:sprocket_cover_mod_19_by_anachris.jpg?direct&300|}} {{:techtalk:ref:engmech:sprocket_cover_mod_20_by_anachris.jpg?direct&300|}} \\
 {{:techtalk:ref:engmech:sprocket_cover_mod_22_by_anachris.jpg?direct&300|}} {{:techtalk:ref:engmech:sprocket_cover_mod_23_by_anachris.jpg?direct&300|}} {{:techtalk:ref:engmech:sprocket_cover_mod_24_by_anachris.jpg?direct&300|}} \\
+A brass woven mesh sheet was cut as a backing for the sprocket cover. \\
+(unpolished, mill finish, ASTM E2016-06, 12" width, 12" length, 0.025" wire diameter, 54% open area) \\
+{{:techtalk:ref:engmech:sprocket_cover_mod_21_by_anachris.jpg?direct&200|}} \\
+Finished product: \\
 {{:techtalk:ref:engmech:sprocket_cover_mod_25_by_anachris.jpg?direct&300|}} \\

Trace: • REF: Engine Mechanicals - Sub-02F • EVO: Carburetor, Intake Manifold & Exhaust • W E L C O M E !

Differences

Navigation

Search

Toolbox