Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
techtalk:ref:tools172 [2020/04/25 19:18] hippysmack [Lifters] |
techtalk:ref:tools172 [2024/01/24 23:09] (current) hippysmack |
||
|---|---|---|---|
| Line 14: | Line 14: | ||
| The block is used to press the plunger down. A spare pushrod or screwdriver can also be used to depress the plunger. \\ | The block is used to press the plunger down. A spare pushrod or screwdriver can also be used to depress the plunger. \\ | ||
| - | {{:techtalk:ref:tools:lifter_holding_tool_1_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM http://xlforum.net/forums/showthread.php?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_2_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM http://xlforum.net/forums/showthread.php?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_3_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM http://xlforum.net/forums/showthread.php?t=2076454&page=4)) \\ | + | {{:techtalk:ref:tools:lifter_holding_tool_1_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_2_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_3_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) \\ |
| - | {{:techtalk:ref:tools:lifter_holding_tool_4_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM http://xlforum.net/forums/showthread.php?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_5_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM http://xlforum.net/forums/showthread.php?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_6_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM http://xlforum.net/forums/showthread.php?t=2076454&page=4)) \\ | + | {{:techtalk:ref:tools:lifter_holding_tool_4_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_5_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) {{:techtalk:ref:tools:lifter_holding_tool_6_by_ngot8r.jpg?direct&300|}} ((photo by NGOT8R of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-engine-conversions/199567-converting-from-1250-to-1275/page4?t=2076454&page=4)) \\ |
| + | |||
| + | ---- | ||
| A doglegged pick works good for removing the retainer clip and removing the internals. A small flat head screwdriver works also. \\ | A doglegged pick works good for removing the retainer clip and removing the internals. A small flat head screwdriver works also. \\ | ||
| Line 24: | Line 26: | ||
| {{:techtalk:ref:svcproc:lifter_disassembly_7_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:svcproc:lifter_disassembly_12_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:svcproc:lifter_disassembly_14_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:ref:svcproc:lifter_disassembly_7_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:svcproc:lifter_disassembly_12_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:svcproc:lifter_disassembly_14_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | |||
| + | |||
| + | ---- | ||
| + | |||
| + | If you just need to store lifters temporarily for a quick removal / installation and have a pegboard, you can use a couple pegs as a holder for lifters. \\ | ||
| + | The two legged pegs with a cut piece of gas tubing to snug against the lifters works well. \\ | ||
| + | Then simply cover them with a rag or towel awaiting an oil soak and installation. \\ | ||
| + | |||
| + | {{:techtalk:ref:tools:temp_lifter_holders_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:temp_lifter_holders_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | |||
| \\ | \\ | ||
