Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ref:body32 [2018/07/05 02:28] hippysmack [Re-locating the Bottom Clamp] |
techtalk:ref:body32 [2022/03/09 05:15] ixl2relax ↷ Page name changed from techtalk:ref:body06 to techtalk:ref:body32 |
||
---|---|---|---|
Line 6: | Line 6: | ||
This was made from a standard aluminium strip from the local aluminum supplier (50 mm wide, thickness 4.3 mm / 11/64 in) cut to shape with a brushed finish. | This was made from a standard aluminium strip from the local aluminum supplier (50 mm wide, thickness 4.3 mm / 11/64 in) cut to shape with a brushed finish. | ||
- | Finshed product: | + | Finshed product: ((photo by girlsbike of the XLFORUM http://xlforum.net/forums/showthread.php?t=1313996)) |
|{{:techtalk:ref:body:detachable_windshield_lowering_bracket_4_by_girlsbike.jpg?direct&300|}}| | |{{:techtalk:ref:body:detachable_windshield_lowering_bracket_4_by_girlsbike.jpg?direct&300|}}| | ||
- | Fitting stages: | + | Fitting stages: ((photos by girlsbike of the XLFORUM http://xlforum.net/forums/showthread.php?t=1313996)) |
|{{:techtalk:ref:body:detachable_windshield_lowering_bracket_1_by_girlsbike.jpg?direct&300|}}|{{:techtalk:ref:body:detachable_windshield_lowering_bracket_2_by_girlsbike.jpg?direct&300|}}|{{:techtalk:ref:body:detachable_windshield_lowering_bracket_3_by_girlsbike.jpg?direct&300|}}| | |{{:techtalk:ref:body:detachable_windshield_lowering_bracket_1_by_girlsbike.jpg?direct&300|}}|{{:techtalk:ref:body:detachable_windshield_lowering_bracket_2_by_girlsbike.jpg?direct&300|}}|{{:techtalk:ref:body:detachable_windshield_lowering_bracket_3_by_girlsbike.jpg?direct&300|}}| | ||
Line 16: | Line 16: | ||
===== Re-locating the Bottom Clamp ===== | ===== Re-locating the Bottom Clamp ===== | ||
- | Finished product: | + | Finished product: ((photos by CitySlicker of the XLFORUM http://xlforum.net/forums/showthread.php?t=1313996)) |
|{{:techtalk:ref:body:lowering_the_detachable_windshield_6_by_cityslicker.jpg?direct&300|}}|{{:techtalk:ref:body:lowering_the_detachable_windshield_7_by_cityslicker.jpg?direct&300|}}|{{:techtalk:ref:body:lowering_the_detachable_windshield_8_by_cityslicker.jpg?direct&300|}}| | |{{:techtalk:ref:body:lowering_the_detachable_windshield_6_by_cityslicker.jpg?direct&300|}}|{{:techtalk:ref:body:lowering_the_detachable_windshield_7_by_cityslicker.jpg?direct&300|}}|{{:techtalk:ref:body:lowering_the_detachable_windshield_8_by_cityslicker.jpg?direct&300|}}| | ||
- | Process stages: | + | Process stages: ((photos by CitySlicker of the XLFORUM http://xlforum.net/forums/showthread.php?t=1313996)) |
* Remove the brackets and tie a string between the clamp holes to get the center line and keep the clamped angle the same. | * Remove the brackets and tie a string between the clamp holes to get the center line and keep the clamped angle the same. | ||
Line 26: | Line 26: | ||
* This one was drilled 1-1/4" up in a drill press. | * This one was drilled 1-1/4" up in a drill press. | ||
* Be sure to leave enough meat between the hole O.D. and the edge for strength. | * Be sure to leave enough meat between the hole O.D. and the edge for strength. | ||
- | * Use the same process and measurements on both sides. | + | * Use the same process and measurements on both sides first. |
* You may find that the factory holes are not quite in the same place on both brackets. | * You may find that the factory holes are not quite in the same place on both brackets. | ||
+ | * You may also find that your exact (matched) measurements would end with the new hole being closer to the edge than the other bracket. So, you'll have to improvise a little. | ||
* If the new holes aren't perfectly drilled to match on both sides, it'll still work. | * If the new holes aren't perfectly drilled to match on both sides, it'll still work. | ||
* It will probably be barely noticeable if at all. | * It will probably be barely noticeable if at all. |