Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
techtalk:evo:engmech02 [2022/09/10 03:51] hippysmack [Cam Bushings] |
techtalk:evo:engmech02 [2023/08/13 02:08] ixl2relax [Sub Documents] |
||
---|---|---|---|
Line 1: | Line 1: | ||
[[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
+ | |||
+ | |||
====== EVO: Engine Mechanicals ====== | ====== EVO: Engine Mechanicals ====== | ||
Line 12: | Line 14: | ||
====== Camshafts ====== | ====== Camshafts ====== | ||
+ | The cams get oiled by drainage from the rocker boxes and splash oil in the bottom end. \\ | ||
+ | Oil flows off the pushrod side of the rocker boxes through the pushrod covers, into vertical holes in the lifter bores and into the gearcase. \\ | ||
+ | Oil falls on the cam lobes on the way down this hole. Some of this oil is transferred between the gear teeth. \\ | ||
+ | The rear intake (#2) cam gets a little oil spray from the right case oil feed galley through the small orifice underneath the open cavity in the case. \\ | ||
+ | That oil is transferred between the teeth of the cams. \\ | ||
+ | Oil flung off the cams lands in the gearcase to be collected into the scavenge (return) side of the oil pump. \\ | ||
+ | |||
+ | 1992-up Cam Gear Oiler Hole in the Right Case. \\ | ||
+ | Below are pics of the restricted orifice underneath the oil feed galley in the case that shoots a small stream onto #2 cam. \\ | ||
+ | #2 cam rotates counterclockwise and the oil is sprayed on the right side of the cam gear for extra cooling (transferred to all cams). | ||
+ | |||
+ | | (L) 92-99 ((photo by Hippysmack of the XLFORUM)), (R) 2000 Up ((photo by Bruce of the XLFORUM http://xlforum.net/forums/showthread.php?t=1118529&page=2up)) cam oiling hole from the feed galley || | ||
+ | | {{:techtalk:evo:oil:92-99_cam_oiler_hole_by_hippysmack.jpg?direct&300|}} |{{:techtalk:evo:oil:2000_up_cam_oiler_hole_by_bruce.jpg?direct&300|}}| | ||
+ | |||
===== Cam Specs - OEM & SE ===== | ===== Cam Specs - OEM & SE ===== | ||
Line 64: | Line 80: | ||
===== Removing / Installing Evo Cams ===== | ===== Removing / Installing Evo Cams ===== | ||
- | ===== Sub Documents ===== | + | ==== Sub Documents ==== |
* [[techtalk:evo:engmech02a|Installing Evo Cams (91 and Up)]] | * [[techtalk:evo:engmech02a|Installing Evo Cams (91 and Up)]] | ||
Line 140: | Line 156: | ||
|{{:techtalk:evo:oil:cam_bushing_oiling_6_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:cam_bushing_oiling_8_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:cam_bushing_oiling_7_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:evo:oil:cam_bushing_oiling_6_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:cam_bushing_oiling_8_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:cam_bushing_oiling_7_by_hippysmack.jpg?direct&300|}}| | ||
+ | |||
+ | |||
====== Lifters (tappets) ====== | ====== Lifters (tappets) ====== | ||
- | ===== Sub-Documents ===== | + | ==== Sub-Documents ==== |
* [[techtalk:evo:engmech02b|91-99 Lifter Pin Upgrade to 00-05 Lifter Pin Screws]] | * [[techtalk:evo:engmech02b|91-99 Lifter Pin Upgrade to 00-05 Lifter Pin Screws]] | ||
* [[techtalk:evo:engmech02c|Hydraulic Lifter - Mechanical and Hydraulic Operation]] | * [[techtalk:evo:engmech02c|Hydraulic Lifter - Mechanical and Hydraulic Operation]] | ||
+ | * [[techtalk:evo:engmech02d|Why 1986-up Lifters Clack on Initial Startup]] | ||
See also in the Sportsterpedia; \\ | See also in the Sportsterpedia; \\ |