Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
techtalk:ref:tools810 [2021/01/21 02:17] hippysmack |
— (current) | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
- | ====== REF: Thread Identification ====== | ||
- | \\ | ||
- | ====== Threads Per Inch (TPI) vs Thread Pitch ====== | ||
- | Threads per inch, commonly abbreviated as TPI, is a term frequently used in US fasteners and is a term used to help identify how many threads are in an inch. \\ | ||
- | To determine treads per inch, an inch of the threads are measured longways and then the peaks on the fastener are counted within that inch. \\ | ||
- | For threads shorter than 1 in, you can measure half an inch of threads and double the result to get the TPI. \\ | ||
- | |||
- | Thread pitch is a term used for metric fasteners and is the distance from one thread to the adjacent thread measured longways across the thread peaks. \\ | ||
- | |||
- | ====== US Threads ====== | ||
- | US threads generally have 3 numbers although the last can be left off unless required. \\ | ||
- | The first number is a whole number and/or fraction the second number is the threads per in (TPI), followed by the length in inches. \\ | ||
- | The diameter is the outside diameter of the thread peaks. \\ | ||
- | In this example of a 1/4" bolt bolt; 1/4" x 20 x 1-1/2" states that the app. diameter of the threads is 1/4", the TPI is 20 and it's 1-1/2" long. | ||
- | |||
- | ====== Metric Threads ====== | ||
- | |||
- | Metric bolts are written down as an "M" followed by 3 numbers and again the last can be left off unless required. \\ | ||
- | The first number is the diameter, the second the thread pitch, and the third the length in millimeters. ((http://raygirling.com/metthrpt.htm)) \\ | ||
- | The diameter is the outside diameter of the thread peaks. \\ | ||
- | |||
- | In this example of a 10mm bolt; M10x1.25x35 states that the diameter of the threads is 10mm, the thread pitch is 1.25mm and it's 35mm long. \\ | ||
- | |||
- | | Metric Thread Pitch |||| | ||
- | |Bolt Diameter|Standard Thread Pitch (mm)|Fine Thread Pitch (mm)|Extra Fine Thread Pitch (mm)| | ||
- | |4mm|0.70| - | - | | ||
- | |5mm|0.80| - | - | | ||
- | |6mm|1.00| - | - | | ||
- | |7mm|1.00| - | - | | ||
- | |8mm|1.25|1.00| - | | ||
- | |10mm|1.50|1.25|1.00| | ||
- | |12mm|1.75|1.50|1.25| | ||
- | |14mm|2.00|1.50| - | | ||
- | |16mm|2.00| - | - | | ||
- | |18mm|2.50| - | - | | ||
- | |20mm|2.50| - | - | | ||
- | |24mm|3.00| - | - | | ||
- | |||
- | |||
- | |||
- | |||
- | |||
- | \\ | ||
- | \\ | ||
- | |||
- | |||
- | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | ||
- | |||