Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
techtalk:ref:tools159 [2018/12/16 17:58] hippysmack created |
techtalk:ref:tools159 [2024/01/24 22:39] (current) hippysmack |
||
---|---|---|---|
Line 1: | Line 1: | ||
[[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
- | ====== REF: Tools - 126 ====== | + | ====== REF: Tools - 159 ====== |
- | ====== Multimeter ====== | + | ====== Multimeter (VOM) ====== |
+ | See also, [[techtalk:evo:elec01#evoelectrical_system|Electrical Basics]] in the Sportsterpedia. \\ | ||
+ | |||
+ | A multimeter or a multitester, also known as a VOM (volt-ohm-milliammeter), is an electronic measuring instrument that combines several measurement functions in one unit. ((https://en.wikipedia.org/wiki/Multimeter)) \\ | ||
+ | A typical multimeter can measure voltage, current, and resistance. \\ | ||
+ | Analog multimeters use a microammeter with a moving pointer to display readings. \\ | ||
+ | Digital multimeters (DMM, DVOM) have a numeric display, and may also show a graphical bar representing the measured value. \\ | ||
+ | Digital multimeters are now far more common due to their cost and precision, but analog multimeters are still preferable in some cases, for example when monitoring a rapidly varying value. \\ | ||
+ | |||
+ | A multimeter can be a hand-held device useful for basic fault finding and field service work, or a bench instrument which can measure to a very high degree of accuracy. ((https://en.wikipedia.org/wiki/Multimeter)) \\ | ||
+ | They can be used to troubleshoot electrical problems in a wide array of industrial and household devices such as electronic equipment, motor controls, domestic appliances, power supplies, and wiring systems. \\ | ||
+ | |||
+ | Multimeters are available in a wide range of features and prices. ((https://en.wikipedia.org/wiki/Multimeter)) \\ | ||
+ | Cheap multimeters can cost less than US$10, while laboratory-grade models with certified calibration can cost more than US$5,000. | ||
+ | |||
+ | |||
+ | Multimeters are extremely useful and are pretty hardy. ((sifty of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/146604-first-harley-1975-xl1000-caf%C3%A9-project/page42?t=1592463&page=42)) \\ | ||
+ | But using the wrong setting, wrong scale, or performing the wrong type of measurement will at best give meaningless results, and at worst smoke the meter. \\ | ||
+ | |||
+ | * Make sure the dial is on Ohms if checking resistance. | ||
+ | * DC Volts if checking voltage. | ||
+ | * Amps if checking current (usually also have to change the red test lead to the 10A terminal socket). | ||
+ | |||
+ | * Trying to read DC volts while the meter is in AC mode is pretty common (and frustrating). | ||
+ | * Putting the test leads across 12V with the leads in the amp range will most likely blow a fuse (or worse) which can cause unwanted delays while you fix/replace the meter. | ||
+ | * When reading resistance (ohms setting) you should short the leads together initially and read what the display says. | ||
+ | * Subtract this value if the meter cannot be zeroed. \\ (if the meter reads 0.2 ohms with the leads shorted, and 6.4 ohms across a winding, the true resistance will be 6.2 ohms). | ||
+ | * Make a good contact with the probes when trying to read the display. | ||
+ | * The values may move a little, but generally they will fluctuate around a meaningful value if the contact point is solid. | ||
+ | |||
+ | | See also [[techtalk:ref:svcproc30#reftroubleshooting_-_07|Testing an oil pressure switch]] | When checking ohms, first check that the meter \\ reads '0' ohms with leads pressed together. ((photo by Hippysmack)) | | ||
+ | |{{techtalk:ref:svcproc:testing_the_oil_pressure_switch_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:multimeter_on_ohms_scale.jpg?direct&300|}}| | ||
+ | |||
+ | ====== Probe Mod ====== | ||
+ | |||
+ | You can buy a couple alligator clips from an auto parts / electronic store and gently crimp the ends over the end of the straight probes. \\ | ||
+ | This will allow you to clip onto pinouts for testing. \\ | ||
+ | You can also lightly wrap electrical tape over the assembly for working in areas where the pins are close to each other so they don't make contact. \\ | ||
+ | |||
+ | {{:techtalk:ref:tools:multimeter_probe_mod_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:ref:tools:multimeter_probe_mod_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
\\ | \\ |