| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| techtalk:ref:notes106 [2019/01/08 23:55] – ixl2relax | techtalk:ref:genmsr12 [2024/01/17 23:14] (current) – hippysmack |
|---|
| [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] |
| ====== REF: Shop Notes and Tips ====== | ====== REF: General-MSR 12 ====== |
| |
| |
| Make sure to remove any rubber or plastic parts before soaking. \\ | Make sure to remove any rubber or plastic parts before soaking. \\ |
| Also check the label for safety precautions. \\ | Also check the label for safety precautions. \\ |
| Parts that have been sitting for years may have to be soaked for about 24 hours. \\ | Parts that have been sitting for years may have to be soaked for about 24 hours or more. \\ |
| |
| | Carburetor Cleaner ((photo by Hippysmack)) ||| | | These pistons below were soaked for app. 5 days rinsing each night to remove carbon on top. ((photos by balduc-2 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-motor-engine/sportster-motorcycle-bottom-end/163867-cam-cover-removal/page2?s=731c426f4dea033958967a4ac51dfc9e#post3495246)) || |
| |{{:techtalk:ref:tools:parts_cleaner_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:oil:parts_cleaner_4.1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:parts_cleaner_3_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:ref:genmsr:cleaning_pistons_with_chem_dip_1_by_balduc-2.jpg?direct&300|}}|{{:techtalk:ref:genmsr:cleaning_pistons_with_chem_dip_2_by_balduc-2.jpg?direct&300|}}| |
| | |
| | | This oil pump soaked overnite to loosen the body to cover gasket. ((photo by Hippysmack)) ||| |
| | |{{techtalk:ref:genmsr:parts_cleaner_1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_4.1_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_3_by_hippysmack.jpg?direct&300|}}| |
| |
| This oil pump had to be soaked overnite before the cover would separate from the body. \\ | This oil pump had to be soaked overnite before the cover would separate from the body. \\ |
| Keep in mind, any rubber parts on the inside will have to be replaced before installation. \\ | Keep in mind, any rubber parts on the inside will have to be replaced before installation. \\ |
| | Soaking gaskets for more easy removal ((photos by Hippysmack)) ||| | | After soaking, rinse the body, take it apart and rinse the insides and parts. ((photos by Hippysmack)) ||| |
| |{{:techtalk:ref:tools:parts_cleaner_4_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:parts_cleaner_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:tools:parts_cleaner_5_by_hippysmack.jpg?direct&300|}}| | |{{techtalk:ref:genmsr:parts_cleaner_4_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_2_by_hippysmack.jpg?direct&300|}}|{{techtalk:ref:genmsr:parts_cleaner_5_by_hippysmack.jpg?direct&300|}}| |
| | |
| |
| ==== Spray-on Brake Cleaner ==== | ==== Spray-on Brake Cleaner ==== |
| ---- | ---- |
| |
| | \\ |
| | |
| | |
| |
| [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]] |
