Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
techtalk:ref:engmech01q [2019/02/18 05:38] hippysmack [Roller end manuf. defect repaired] |
techtalk:ref:engmech01q [2020/10/27 00:27] hippysmack [Roller end manuf. defect repair] |
||
|---|---|---|---|
| Line 88: | Line 88: | ||
| The longer flats also allow higher lifts. | The longer flats also allow higher lifts. | ||
| - | ===== Roller end manuf. defect repair ===== | ||
| - | It seems aftermarket lifters have a tendency to be wide at the roller end (at the opposite pins holding the roller). \\ | ||
| - | Measure them before installing to be sure they won't scratch the lifter bore when turned home. ((Hippysmack of the XLFORUM http://xlforum.net/forums/showthread.php?p=5283285&highlight=lifter+pins#post5283285)) \\ | ||
| - | |||
| - | |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_3_by_hippysmack.jpg?direct&300|}}| | ||
| - | |||
| - | Upon measuring, the main body on this particular set of Fueling lifters were .903" on the main body with the roller end being .9035". \\ | ||
| - | They were all chucked in a lathe, and light sanded with medium grit sanding tape which brought them down to .903" all around the base. | ||
| - | |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_4_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_5_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_6_by_hippysmack.jpg?direct&300|}}| | ||
| - | |||
| - | |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_7_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_8_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_9_by_hippysmack.jpg?direct&300|}}| | ||
| - | |||
| - | |{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_10_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_11_by_hippysmack.jpg?direct&300|}}|{{:techtalk:ref:engmech:sizing_a_fueling_lifter_base_12_by_hippysmack.jpg?direct&300|}}| | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | \\ | ||
| - | |I have my prototype hone drying....400 grit Gorilla glued to the ball hone shaft. | ||
| ===== Other Useful Links ===== | ===== Other Useful Links ===== | ||
| This is a very good XLFORUM discussion thread on [[http://xlforum.net/forums/showthread.php?t=1933342&highlight=disassembling+lifters|lifters and high lift cams]]. \\ | This is a very good XLFORUM discussion thread on [[http://xlforum.net/forums/showthread.php?t=1933342&highlight=disassembling+lifters|lifters and high lift cams]]. \\ | ||
