Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
techtalk:ref:body50 [2018/04/17 23:26] ixl2relax |
techtalk:ref:body50 [2022/03/09 04:53] ixl2relax ↷ Page name changed from techtalk:ref:body20 to techtalk:ref:body50 |
||
---|---|---|---|
Line 1: | Line 1: | ||
[[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | [[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] | ||
====== REF: Body Parts ====== | ====== REF: Body Parts ====== | ||
+ | |||
+ | \\ | ||
+ | |||
+ | ====== FENDERS ====== | ||
+ | |||
+ | |||
+ | |||
+ | \\ | ||
+ | |||
+ | ===== Tips ===== | ||
+ | |||
+ | **2005 XL Model Wire Harness Elbow**: ((HD TECH Tip (TT059) dated May 5, 2009)) \\ | ||
+ | If you remove the RH wire harness elbow (73205-05), it is recommended to install washer (6859M) on the mounting bolt when reinstalling the elbow. \\ | ||
+ | This is to prevent future damage to the elbow’s mounting hole. \\ | ||
+ | This washer was installed in production as of February 27, 2005. \\ | ||
+ | |||
+ | |||
+ | \\ | ||
+ | |||
====== Mud Flaps ====== | ====== Mud Flaps ====== | ||
Line 11: | Line 30: | ||
- | |{{techtalk:ref:body:mud_flap_a_by_zoharo.jpg?direct&600|}} ((Pic by Zoharo of the XLFORUM http://xlforum.net/forums/showthread.php?t=462528))| | + | {{techtalk:ref:body:mud_flap_a_by_zoharo.jpg?direct&300|}} ((Pic by Zoharo of the XLFORUM http://xlforum.net/forums/showthread.php?t=462528)) {{techtalk:ref:body:mud_flap_b_by_zoharo.jpg?direct&300|}} ((Pic by Zoharo of the XLFORUM http://xlforum.net/forums/showthread.php?t=462528)){{techtalk:ref:body:mud_flap_c_by_zoharo.jpg?direct&300|}} ((Pic by Zoharo of the XLFORUM http://xlforum.net/forums/showthread.php?t=462528)) |
- | + | ||
- | |{{techtalk:ref:body:mud_flap_b_by_zoharo.jpg?direct&600|}} ((Pic by Zoharo of the XLFORUM http://xlforum.net/forums/showthread.php?t=462528))| | + | |
- | + | ||
- | |{{techtalk:ref:body:mud_flap_c_by_zoharo.jpg?direct&600|}} ((Pic by Zoharo of the XLFORUM http://xlforum.net/forums/showthread.php?t=462528))| | + | |
+ | There is an aluminum brace on the inside of the fender. It is "key" to maintaining the shape like the fender as the flap extends downward. \\ | ||
+ | The inner view shows the piece of aluminum bar stock bent to the shape of the inside of the rear fender. \\ | ||
+ | It's clamped and drilled, and attached using small stove bolts. \\ | ||
+ | {{:techtalk:ref:body:mud_flap_d_by_zohara.jpg?direct&300|}} ((Pic by Zoharo of the XLFORUM http://xlforum.net/forums/showthread.php?t=462528&page=3)) {{:techtalk:ref:body:mud_flap_e_by_zohara.jpg?direct&300|}} ((Pic by Zoharo of the XLFORUM http://xlforum.net/forums/showthread.php?t=462528&page=3)) | ||