Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
techtalk:ih:oil04 [2025/10/20 03:14] – old revision restored (2024/12/01 21:59) hippysmacktechtalk:ih:oil04 [2025/10/20 03:47] (current) – [Oil Lines to the Rockers] hippysmack
Line 286: Line 286:
 ====== Oil Lines to the Rockers ====== ====== Oil Lines to the Rockers ======
 Installation: \\ Installation: \\
-The ends are slightly different sizes. ((Ivan RoachCoach of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/92089-oil-pressure-issues/page2#post1917701)) \\ 
-The larger-sized ends go on the case and the smaller-diameter ones go to the rockers. \\ 
-In other words the closer they are to the oil pump, the bigger they should be. \\ 
-Most people never even notice this. \\ 
-Issues getting oil to the top end: \\ 
-If your pump is primed, and the breather gear is properly timed, then the problem lies in the lines and/or their fittings. \\ 
- 
 If you have a leak here, you may not have to replace any parts. \\ If you have a leak here, you may not have to replace any parts. \\
 Try to uninstall them, clean, inspect and reinstall them and see what happens. \\ Try to uninstall them, clean, inspect and reinstall them and see what happens. \\
Line 314: Line 307:
 |  Rocker oil line ((photo by Ironshred of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/183535-earl-leak?t=1974660))  | |  Rocker oil line ((photo by Ironshred of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/183535-earl-leak?t=1974660))  |
 |{{:techtalk:ih:oil:82_rocker_oil_lines_by_ironshred.jpg?direct&200|}}| |{{:techtalk:ih:oil:82_rocker_oil_lines_by_ironshred.jpg?direct&200|}}|
 +
 +There are rubber grommets on both ends of the oil lines. ((IronMick of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/92089-oil-pressure-issues?t=753175&highlight=split+rocker+box)) \\
 +Some guys install two on each end, which is a wrong thing to do. \\
 +Sometimes the rubber from an improperly installed grommet plugs the oil line. \\
 +Before going into the gearcase (to check for low / no oil to the rocker boxes); \\
 +Remove both oil lines, and check the rubbers on both ends of each. \\
 +
 +|  Oil line sleeves. ((photos by sc72 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/159099-rocker-box-oil-line?t=1704463))  ||
 +|{{:techtalk:ih:oil:83_model_oil_line_sleeves_1_by_sc72.jpg?direct&250|}}|{{:techtalk:ih:oil:83_model_oil_line_sleeves_2_by_sc72.jpg?direct&250|}}|
 +
  
 ====== Braided Oil Lines ====== ====== Braided Oil Lines ======

Trace: