Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
|
techtalk:evo:susp03e [2020/05/25 06:33] hippysmack [Bearing Spacer] |
techtalk:evo:susp03e [2021/02/02 06:34] hippysmack [Bearing Lockring] |
||
|---|---|---|---|
| Line 5: | Line 5: | ||
| \\ | \\ | ||
| + | ===== Swingarm ===== | ||
| + | \\ | ||
| + | ==== 1995-1998 Swingarm (47547-87B) ==== | ||
| + | {{:techtalk:evo:susp:1998_sportster_swingarm_dims_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | |||
| + | {{:techtalk:evo:susp:1998_sportster_swingarm_dims_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | |||
| + | {{:techtalk:evo:susp:1998_sportster_swingarm_dims_6_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_7_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:1998_sportster_swingarm_dims_8_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | |||
| + | ===== Swingarm Pivot Bolt ===== | ||
| + | \\ | ||
| + | ==== 1993-2003 Pivot Bolt (41568-81B) ==== | ||
| + | |||
| + | {{:techtalk:evo:susp:1998_sportster_swingarm_pivot_bolt_dims_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
| ===== Bearing Lockring ===== | ===== Bearing Lockring ===== | ||
| Line 11: | Line 25: | ||
| It has no part number as it comes in a set with the bearings. \\ | It has no part number as it comes in a set with the bearings. \\ | ||
| It's actually just a retaining ring acting as both a stop and a spacer between each bearing race when they are installed. \\ | It's actually just a retaining ring acting as both a stop and a spacer between each bearing race when they are installed. \\ | ||
| + | |||
| + | Officially, it's a Constant Section Internal Retaining Ring (AKA, Eaton-style or horseshoe snap rings) of the "Bearing Snap Ring" variety. ((https://www.prospectfastener.com/snaprings/internalrings/constant-section-internal-rings)) \\ | ||
| + | It features a uniform, constant section. This means that the material used to make the ring is the same width at any point along the circumference of the ring. \\ | ||
| + | This allows full seat of the races against it as they are installed. \\ | ||
| + | These can be bought from fastener companies in carbon steel as plain or with oil embedded. \\ | ||
| This is a NOS ring. \\ | This is a NOS ring. \\ | ||
| Line 34: | Line 53: | ||
| This bushing sets the length measurement for the proper clamp force on the swingarm part assembly and acts as a spacer bushing thru the left pivot. \\ | This bushing sets the length measurement for the proper clamp force on the swingarm part assembly and acts as a spacer bushing thru the left pivot. \\ | ||
| + | This is a used spacer. \\ | ||
| {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_pivot_bolt_spacer_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | ===== Pivot Spacer Bushing ===== | ||
| + | |||
| + | Used on 1986-2003, all models and 1982-1985 square tube swingarms. \\ | ||
| + | This bushing is installed in the left pivot and the pivot spacer is installed into this bushing. \\ | ||
| + | |||
| + | Below are dims for the replacement bushing from V-twin. \\ | ||
| + | |||
| + | {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
| + | {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
| + | |||
| + | {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_3_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) | ||
| + | {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_4_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_bushing_vt_47083-81a_pic_5_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack))\\ | ||
| ===== Bearing Dust Shield ===== | ===== Bearing Dust Shield ===== | ||
| Line 43: | Line 75: | ||
| Part# (41579-81), 2 required. \\ | Part# (41579-81), 2 required. \\ | ||
| + | This is a used dust shield. \\ | ||
| {{:techtalk:evo:susp:swingarm_bearing_dust_shield-_used-_dim1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_bearing_dust_shield-_used-_dim2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | {{:techtalk:evo:susp:swingarm_bearing_dust_shield-_used-_dim1_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) {{:techtalk:evo:susp:swingarm_bearing_dust_shield-_used-_dim2_by_hippysmack.jpg?direct&300|}} ((photo by Hippysmack)) \\ | ||
