Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
techtalk:evo:oil03i [2018/12/24 00:37] hippysmack [Spring Washer] |
techtalk:evo:oil03i [2024/01/05 03:43] hippysmack |
||
---|---|---|---|
Line 2: | Line 2: | ||
====== EVO: Oiling & Lubrication - Sub-03I ====== | ====== EVO: Oiling & Lubrication - Sub-03I ====== | ||
====== 86-90 Oil Pump (26204-86) Individual Parts and Pics ====== | ====== 86-90 Oil Pump (26204-86) Individual Parts and Pics ====== | ||
+ | See also See also [[techtalk:evo:oil03j#oil_pump_26204-86_parts_approximate_dims|86-90 Oil Pump (26204-86) Parts (approximate) Dims]] | ||
====== Oil Pump Body and Cover ====== | ====== Oil Pump Body and Cover ====== | ||
===== Oil Pump Body ===== | ===== Oil Pump Body ===== | ||
Line 21: | Line 22: | ||
===== Oil Pump Cover ===== | ===== Oil Pump Cover ===== | ||
- | |||
* The bottom cover is HD catalog number (26486-86). | * The bottom cover is HD catalog number (26486-86). | ||
* The casting number (26487-86) is in the feed cavity. | * The casting number (26487-86) is in the feed cavity. | ||
Line 31: | Line 31: | ||
|{{:techtalk:evo:oil:86-90_oil_pump_cover_4_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:86-90_oil_pump_cover_5_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:86-90_oil_pump_cover_6_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:evo:oil:86-90_oil_pump_cover_4_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:86-90_oil_pump_cover_5_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:86-90_oil_pump_cover_6_by_hippysmack.jpg?direct&300|}}| | ||
- | ===== Gearshaft ===== | + | ====== Gearshaft ====== |
The gear shaft part number (26488-75) was used from 77-90. \\ | The gear shaft part number (26488-75) was used from 77-90. \\ | ||
The gear has 20 teeth. \\ | The gear has 20 teeth. \\ | ||
Line 39: | Line 39: | ||
|{{:techtalk:evo:oil:86-90_oil_pump_gearshaft_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:86-90_oil_pump_gearshaft_2_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:evo:oil:86-90_oil_pump_gearshaft_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:86-90_oil_pump_gearshaft_2_by_hippysmack.jpg?direct&300|}}| | ||
- | ===== Gearshaft Retaining Ring ===== | + | ====== Gearshaft Retaining Ring ====== |
Gear shaft retaining ring (26497-75) was used on 77-90 model oil pumps. \\ | Gear shaft retaining ring (26497-75) was used on 77-90 model oil pumps. \\ | ||
It keeps the inner plate, return gerotors and gearshaft locked in the pump. \\ | It keeps the inner plate, return gerotors and gearshaft locked in the pump. \\ | ||
Line 46: | Line 46: | ||
|{{:techtalk:evo:oil:86-90_oil_pump_gearshaft_retaining_ring_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:86-90_oil_pump_gearshaft_retaining_ring_2_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:evo:oil:86-90_oil_pump_gearshaft_retaining_ring_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:86-90_oil_pump_gearshaft_retaining_ring_2_by_hippysmack.jpg?direct&300|}}| | ||
- | ===== Gearshaft Pins ===== | + | ====== Gearshaft Pins ====== |
The gear shaft solid pin (26430-76), was used in 77-90 oil pumps. \\ | The gear shaft solid pin (26430-76), was used in 77-90 oil pumps. \\ | ||
The diameter and lengths of the pins vary. \\ | The diameter and lengths of the pins vary. \\ | ||
Line 63: | Line 63: | ||
The installed lower pin also holds the outer plate in the pump body. \\ | The installed lower pin also holds the outer plate in the pump body. \\ | ||
The length of this pin could be a potential issue under the right conditions. \\ | The length of this pin could be a potential issue under the right conditions. \\ | ||
- | Too short and it could get make it's way into the hole in the plate and tear the seal. \\ | + | Too short and it could get make it's way into the hole in the plate and upset the center of the pressed in seal. \\ |
This could induce slop in the plate and allow it to try to spin the plate against the roll pin in the body. \\ | This could induce slop in the plate and allow it to try to spin the plate against the roll pin in the body. \\ | ||
As well as create a leak from the feed side and allow oil to float up into the engine thru the gearshaft bore. \\ | As well as create a leak from the feed side and allow oil to float up into the engine thru the gearshaft bore. \\ | ||
Line 86: | Line 86: | ||
====== Outer Plate ====== | ====== Outer Plate ====== | ||
- | |||
The outer plate is the bottom plate (with the pump installed). \\ | The outer plate is the bottom plate (with the pump installed). \\ | ||
The feed gerotors sit under this plate. \\ | The feed gerotors sit under this plate. \\ | ||
Line 93: | Line 92: | ||
Notice the difference of the cut out or recessed area of the inside diameter of the outer plates. \\ | Notice the difference of the cut out or recessed area of the inside diameter of the outer plates. \\ | ||
- | This is for the different style of seals. ((DirtyCory of the XLFORUM http://xlforum.net/forums/showthread.php?t=2071153)) \\ | + | This is for the different style of seals. ((DirtyCory of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/194881-let-s-study-the-77-85-oil-pump-parts-and-changes-and-when?t=2071153)) \\ |
Either plate will fit 77-90 oil pumps with their respective seals. \\ | Either plate will fit 77-90 oil pumps with their respective seals. \\ | ||
|{{:techtalk:ih:oil:outer_plates_by_dirtycory_-_annotated.jpg?direct&500|}}| | |{{:techtalk:ih:oil:outer_plates_by_dirtycory_-_annotated.jpg?direct&500|}}| | ||
- | | Outer plate comparison ((photo by DirtyCory of the XLFORUM, annotated by Hippysmack http://xlforum.net/forums/showthread.php?t=2071153)) | | + | | Outer plate comparison ((photo by DirtyCory of the XLFORUM, annotated by Hippysmack https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/194881-let-s-study-the-77-85-oil-pump-parts-and-changes-and-when?t=2071153)) | |
|{{:techtalk:evo:oil:83-90_oil_pump_outer_plate_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:83-90_oil_pump_outer_plate_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:83-90_oil_pump_outer_plate_3_by_hippysmack.jpg?direct&300|}}| | |{{:techtalk:evo:oil:83-90_oil_pump_outer_plate_1_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:83-90_oil_pump_outer_plate_2_by_hippysmack.jpg?direct&300|}}|{{:techtalk:evo:oil:83-90_oil_pump_outer_plate_3_by_hippysmack.jpg?direct&300|}}| |