The ironhead factory service manuals lay out the procedure for 'stripping the motorcycle for repair'.
This covers the procedure for removing / installing the motor and also includes the motor mounts.
However, the whole story is not in the manual.
You can induce added vibration and potential for cracks in the mounts or cases if the mounts aren't installed properly.
Below is the procedure from the manuals for removing and installing the mounts. 1) 2) 3)
To remove the motor (given all other particulars have been removed as this is strictly regarding the mounts themselves);
To install the motor (Again, this is strictly regarding the mounts themselves and all other parts will need to be addressed that were removed);
The 79-85 FSM doesn't give instructions on putting everything back together.
When following the manual procedures, it's possible and actually common to tighten everything up only to find the motor position has cracked the rear mount.
Your motor needs to be “cradled” in the frame. 4)
If it's just put in and tightened up it could be out of alignment and stress one area more than others.
That can set up a harmonic that gets worse at a specific rpm range.
The way the rear mount is designed, it determines the motor location. 5) 6)
The rear mount has to be tightened first, then the other mounts.
It's possible to probable that most rear mount breakage can be attributed to improper assembly techniques, broken frames or loose / missing mounts.
You cannot “pull” the rear mount into place against the other mounts as it will break the mount due to the high amount of leverage from the other mounts.
The front frame tubes may spring sideways slightly but that is the only allowable “pulling”.
All mounts should fit nicely and naturally before tightening.
There is sometimes some wiggle room on the rear mount. 7)
Loosen all the bolts slightly and give it a yank in the direction you need hold and tighten.
DO NOT pull things into position or jam bolts in under pressure!
The bolt holes must line up naturally or the rear mount will break in use.
Don't get in a rush, it will be costly later (regrets if nothing else).
You don't have time to NOT do it right. It will NOT get done later and will leave you beside the road when it breaks.
Put it together right the first time, or you will be forever breaking down.
Another way to do that is to hang the motor by the center (head mount) on the frame. 8)
Use no washers,leave the front mount bolts out and the front mounts loose at the engine.
Start all of your rear mount bolts but don't tighten them up yet. Start all of your front mount bolts but leave them loose.
Now tighten up the rear mount bolts evenly until the rear mount is seated and torque the bolts.
Snug up the front mounts but not tight. Remove the top mount and add washers until you have about 1/32“ play at the top mount.
Tighten front mount bolts, frame and engine. Tighten top mount and you are done.
Please note that a well tuned IronHead does not make any noise. Rather it is a symphony of sounds and, when well set up, you can hear all of them - the valve train, the intake, the exhaust. 9)
A few decades back, I rode with a bunch of established riders that gathered at an indy shop on Sunday mornings. One day a young longhair showed up on an XL Roadster and asked if he could tag along. I was usually up front as the ” Road Captain “ and he was catching dust in the back. He gathered respect soon enough and I paid some more attention to him and his lovely wife. I noticed how long he had to crank the starter before it would run and then sometimes pop, spit and stall. I had my '76 CH with an extensively modified Super B, 10.5 Wiseco's, Morris Mag and 2>1 Jardine header. We would all wait for him to get running and then start ours. Mine would lite right up and do the symphony. His would shake, rattle and roll. It was that way for most of that season and he seemed to think that's how it was supposed to be. I finally felt comfortable enough with this person to ask if I could tune up his bike and he agreed. We did a top to bottom adjustment/tune up while I instructed him on how to keep it running right. It ran smooth, started easily and did the potato potato. He called me as soon as he got home and couldn't believe the new power and how much better it sounded at stop lights. He had the symphony. 10)
The next Sunday I was on route to the shop/ride, rounding a curve on a highway and saw 2 riders on the shoulder. One in a full out leather suit with a sport bike and the other my longhair pal. He was accelerating off a ramp, digging on the power and the symphony as never before. He hit third and his big end rod bearings grenaded. His motor had run so bad for so long it just could no longer take the power it was actually designed to produce. The sport bike rider had stopped to help. For all you guys that are new to the righteous world of Ironheads and their various peculiarities… Noises, as unpleasant as they may be , need to be diagnosed and addressed as soon as possible. Damage is being done anytime a motor isn't running correctly. Don't just assume it's an old design and supposed to be noisy. If you don't have the symphony, find someone who can help you get it. 11)
Installing your Iron Head Engine.
Let's break the mount install into two procedures. 12)
Make sense so far?
The below procedure get's done on the bench previous to motor install.
That's how to get motor in frame correctly. But,prior to motor install make sure kick stand and tab is up to the next 50yrs of service. Bent tabs allow bike to lean excessively. Bikes that lean too much are hard to start and can break crankcases if stand head flexes into case during kickstarting.