REF: Suspension - Sub-04A - Sportsterpedia

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

[[:techtalk:menu|{{  :techtalk:gototechnicalmenu.jpg|}}]]
====== REF: Suspension - Sub-04A ======
\\

====== Outlaw Mac's Air Shock Installation ======
2006 Sportster XL883C -> XL1250C: \\
Article by Outlaw Mac of the XLFORUM ((http://xlforum.net/forums/showthread.php?t=1643496)) \\
Click on a pic to enlarge: \\

|Before ((photo by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))|After ((photo by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))|
|{{:techtalk:ref:susp:air_shocks_installation_7_by_outlaw_mac.jpg?direct&300|}}|{{:techtalk:ref:susp:air_shocks_installation_17_by_outlaw_mac.jpg?direct&300|}}|

|Most of the tools needed, as well as Teflon pipe thread and 1/2" washers. ((photos by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))||
|{{:techtalk:ref:susp:air_shocks_installation_6_by_outlaw_mac.jpg?direct&300|}}|{{:techtalk:ref:susp:air_shocks_installation_16_by_outlaw_mac.jpg?direct&300|}}|

|HEAVY DUTY LOW PROFILE CHROME LOWERING AIR SHOCKS \\ Bought off Ebay, Manufacturer Part Number: 116-256 (replaces 54631-02B) ((photos by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))|||
|{{:techtalk:ref:susp:air_shocks_installation_1_by_outlaw_mac.jpg?direct&200|}}|{{:techtalk:ref:susp:air_shocks_installation_2_by_outlaw_mac.jpg?direct&200|}}|{{:techtalk:ref:susp:air_shocks_installation_4_by_outlaw_mac.jpg?direct&300|}}|

Extra Parts: \\

|$12 air line kit from Advance Auto Parts. ((photo by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))|1/8" Tank Valves. ((photo by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))|
|{{:techtalk:ref:susp:air_shocks_installation_3_by_outlaw_mac.jpg?direct&300|}}|{{:techtalk:ref:susp:air_shocks_installation_5_by_outlaw_mac.jpg?direct&300|}}|

If you want to skip the air lines and just install the Schrader valves; \\
You can pick them up at the hardware store cheap. \\

|Here's a pic with the part #. ((photo by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))|
|{{:techtalk:ref:susp:air_shocks_installation_18_by_outlaw_mac.jpg?direct&300|}}|

Take off the old shocks and install new the ones, doing one side at a time. \\

|It's recommended to remove the shipping plug AFTER you have the shocks installed. \\ This way you lesson the chance that you may spill some of the oil out if you tip it the wrong way. \\ Then install new 1/8" fittings onto shocks. \\ Run your air line where you want it and slide on the brass ferrule and cap. ((photos by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))|||
|{{:techtalk:ref:susp:air_shocks_installation_8_by_outlaw_mac.jpg?direct&200|}}|{{:techtalk:ref:susp:air_shocks_installation_9_by_outlaw_mac.jpg?direct&200|}}|{{:techtalk:ref:susp:air_shocks_installation_10_by_outlaw_mac.jpg?direct&200|}}|

The Teflon tape isn't necessary as in the pic above. That's not what keeps it air tight. \\
It's the ferrule that keeps it tight. \\
You just hand tighten the cap, then use a wrench and crank it a 1/2 turn, being careful not to over-tighten.

|Make the connections on the other end of the air hose on the 'T' from the kit. \\ Use the little rubber washer like the ferrule on the other end, \ between the cap and the base. ((photos by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))||
|{{:techtalk:ref:susp:air_shocks_installation_11_by_outlaw_mac.jpg?direct&300|}}|{{:techtalk:ref:susp:air_shocks_installation_12_by_outlaw_mac.jpg?direct&200|}}|

1-1/2" washer were used on the top and 2-1/2" washers on the bottom. \\ 
Stock bolt was reused. \\
Torqued to 45-50 ft/lbs for both upper and lower bolts. \\

|Eye to eye with stock shocks. ((photo by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))|Eye to eye with the air shocks. ((photo by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))|This cleared the belt guard. ((photo by Outlaw Mac of the XLFORUM http://xlforum.net/forums/showthread.php?t=1643496))|
|{{:techtalk:ref:susp:air_shocks_installation_14_by_outlaw_mac.jpg?direct&300|}}|{{:techtalk:ref:susp:air_shocks_installation_15_by_outlaw_mac.jpg?direct&200|}}|{{:techtalk:ref:susp:air_shocks_installation_13_by_outlaw_mac.jpg?direct&200|}}|

\\

[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]

Trace: • REF: Service Procedures 9A • EVO: Body Parts - Sub-02A • REF: Service Procedures 11K • REF: Wheels, Brakes & Tires - Sub-03A • IH: Electrical System - Sub-03F • EVO: Electrical System - Sub-03B • REF: Engine Mechanicals - Sub-09N • REF: Suspension - Sub-04A • EVO: Electrical System - Sub-02M • REF: Suspension - Sub-02D