Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
techtalk:ref:engctl50h [2020/01/31 08:10] – ixl2relaxtechtalk:ref:engctl50h [2024/01/14 16:19] (current) – hippysmack
Line 11: Line 11:
  
 ===== Installing & Connecting to the TC88A ===== ===== Installing & Connecting to the TC88A =====
-(Edited post & pics from ESteid of the XLForum - http://xlforum.net/forums/showthread.php?t=1525483)+(Edited post & pics from ESteid of the XLForum - https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-electrical/sportster-motorcycle-electrical-and-ignition/140699-installing-a-twin-tech-tc88a-on-an-04?t=1525483)
  
 **NOTE:** Always remove the Maxi-Fuse while working on the electrical system of the bike to prevent unexpected shorts! **NOTE:** Always remove the Maxi-Fuse while working on the electrical system of the bike to prevent unexpected shorts!
Line 17: Line 17:
 Disconnect the 12-pin connector that plugs into the stock ignition module (under the seat). Remove the two bolts holding the OEM module in place and mount the TC88A unit in it's place. Disconnect the 12-pin connector that plugs into the stock ignition module (under the seat). Remove the two bolts holding the OEM module in place and mount the TC88A unit in it's place.
  
-Using a small screwdriver, or a pick, remove the plastic plug from the face of the 12-pin main harness connector. **Remove** the BROWN/Grey wire from Pin 2 location. This is a power wire, so be sure to tape it up & shrink-wrap it well to prevent it from shorting anywhere. Using the WHITE jumper wire that comes with the tuner, feed the open ended side through the rubber plug (into Pin 2 position) until it is flush with the face of the connector. Then snap the plug back into the face.+Using a small screwdriver, or a pick, remove the plastic plug from the face of the 12-pin main harness connector. **Remove** the BROWN/Gray wire from Pin 2 location. This is a power wire, so be sure to tape it up & shrink-wrap it well to prevent it from shorting anywhere. Using the WHITE jumper wire that comes with the tuner, feed the open ended side through the rubber plug (into Pin 2 position) until it is flush with the face of the connector. Then snap the plug back into the face.
  
 {{:techtalk:ref:engctl:tc88a-hd-connector1-esteid.jpg?300|Image by ESteid}}  {{:techtalk:ref:engctl:tc88a-hd-connector2-esteid.jpg?300|Image by ESteid}}  {{:techtalk:ref:engctl:tc88a-connunitharness-12pin-npaisnel.jpg?205|Image by NPaisnel}} {{:techtalk:ref:engctl:tc88a-hd-connector1-esteid.jpg?300|Image by ESteid}}  {{:techtalk:ref:engctl:tc88a-hd-connector2-esteid.jpg?300|Image by ESteid}}  {{:techtalk:ref:engctl:tc88a-connunitharness-12pin-npaisnel.jpg?205|Image by NPaisnel}}
Line 54: Line 54:
  
 ===== Connecting to the TC88A Off the bike ===== ===== Connecting to the TC88A Off the bike =====
-(Edited pics by Rocketmangb of the XLForum - http://xlforum.net/forums/showthread.php?t=2075733)+(Edited pics by Rocketmangb of the XLForum - https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-electrical/sportster-motorcycle-electrical-and-ignition/198923-tc88a-programming-hardware?t=2075733)
  
 You will need the TC88A unit and the USB Interface USB-INTF (P/N 18014 from Daytona Twin Tec). Set the switch on the USB-INTF to 'TC88A and All Others'.\\ You will need the TC88A unit and the USB Interface USB-INTF (P/N 18014 from Daytona Twin Tec). Set the switch on the USB-INTF to 'TC88A and All Others'.\\

Trace: