Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
techtalk:evo:elec03 [2024/06/14 02:04] – [2004-later - Speedometer WOW Test] ixl2relaxtechtalk:evo:elec03 [2025/01/06 16:20] (current) – [TURN SIGNALS] ixl2relax
Line 272: Line 272:
 \\ \\
  
-==== 2004-later - Speedometer WOW Test ====+==== 2004-later Speedo WOW Test ====
 ((From the Electrical Diagnostic Manual))\\ ((From the Electrical Diagnostic Manual))\\
  
Line 283: Line 283:
 Release trip odometer reset switch. Background lighting should illuminate, gauge needle should sweep its full range of motion, and indicator lamps (check engine, low fuel, battery and security) should illuminate. Release trip odometer reset switch. Background lighting should illuminate, gauge needle should sweep its full range of motion, and indicator lamps (check engine, low fuel, battery and security) should illuminate.
  
 +If instrument module fails "WOW" test, check for loose wiring at the speedometer. If you can, access Diagnostic Trouble Codes.
 +
 +**Tech Notes - 2004-2013**\\
 If instrument module fails "WOW" test, check for battery, ground, ignition, trip odometer reset switch and accessory wiring to speedometer. If instrument module fails "WOW" test, check for battery, ground, ignition, trip odometer reset switch and accessory wiring to speedometer.
  
-**Tech Notes:**\\ 
 Constant power is supplied to the speedometer through Pin2 (Battery) of Connector #20 on the Main Harness. The speedometer turns on when power is applied to Pin6 (Ignition - Conn20). The speedometer proceeds through an initialization sequence every time power is removed (key switch off) and re-applied to Pin1 (Accessory - Conn20). The visible part of this sequence is the check engine lamp, security lamp, backlighting and odometer display. Upon key ON (Run/Off switch set to RUN), the check engine lamp and security lamp will illuminate for four seconds and then (if parameters are normal) will turn off. Constant power is supplied to the speedometer through Pin2 (Battery) of Connector #20 on the Main Harness. The speedometer turns on when power is applied to Pin6 (Ignition - Conn20). The speedometer proceeds through an initialization sequence every time power is removed (key switch off) and re-applied to Pin1 (Accessory - Conn20). The visible part of this sequence is the check engine lamp, security lamp, backlighting and odometer display. Upon key ON (Run/Off switch set to RUN), the check engine lamp and security lamp will illuminate for four seconds and then (if parameters are normal) will turn off.
  
 The Security Lamp (Security Indicator in the speedometer), which is shaped like a 'key', is illuminated by the TSM/TSSM/HFSM using positive voltage on the BROWN/Violet wire. The Security Lamp (Security Indicator in the speedometer), which is shaped like a 'key', is illuminated by the TSM/TSSM/HFSM using positive voltage on the BROWN/Violet wire.
  
-^  Power Sources to Speeometer  ||||| +^  Power Sources to Speedometer  ||||| 
-|  Speedo   |  Pin 5        |  Pin 1           |  Pin 6          |  Pin 7     | +|  Source     |  Battery Fuse  |  Instrument Fuse  |  Accessory Fuse  |  Ground    | 
-|  Conn#20  |  Pin 2        |  Pin 6           |  Pin 1          |  Pin 12    | +|  Conn#20    |  Pin 2         |  Pin 6            |  Pin 1           |  Pin 12    | 
-|  Source   |  Battery Fuse |  Instrument Fuse |  Accessory Fuse |  Ground    | +|  At Speedo  |  Pin 5         |  Pin 1            |  Pin 6           |  Pin 7     | 
-|  When     |  Constant     |  Ignition ON     |  ACC or Ign ON  |  Constant  | +|  When       |  Constant      |  Ignition ON      |  ACC or Ign ON   |  Constant  | 
-^  The results of these connections failing  |||| +^  The results of these connections failing  ||||| 
-|           | * Security lamp\\ .. glows dimly\\ .. during\\ .. 4-second\\ .. bulb check | * Will not do WOW\\ * Speed shows 0\\ * Tach unaffected\\ * Security lamp works\\ * Check Engine lamp\\ .. & battery lamp\\ .. non-functional\\ * No diagnostics | * Speedo non-functional\\ * Security lamp\\ .. will still do\\ .. 4-sec display | * Speedo non-functional\\ * No diagnostics |+|             | * Speedo non-functional\\ * Security lamp\\ .. glows dimly\\ .. during\\ .. 4-second\\ .. bulb check | * Will not do WOW\\ * Speed shows 0\\ * Tach unaffected\\ * Security lamp works\\ * Check Engine lamp\\ .. & battery lamp\\ .. non-functional\\ * No diagnostics | * Speedo non-functional\\ * Security lamp\\ .. will still do\\ .. 4-sec display | * Speedo non-functional\\ * No diagnostics |
  
  
Line 485: Line 487:
 ===== Indicator Lights - Idiot Lights ===== ===== Indicator Lights - Idiot Lights =====
  
-**1992-1994** models used Indicator Units without replaceable individual bulbs - The entire unit (cylindrical housing with pig tail wires) needs to be replaced:\\+**Indicator Lights - Circuit Activation** 
 + 
 +| YEAR | Indicator | Activated By | 
 +| 86-91 |  HiBeam  | Powered from Hi/Lo Switch when on 'HI' | 
 +| ::: |  Turn  | Single Lamp - Powered when either TS Switch Active | 
 +| ::: | HiBeam & TS Indicators Are Always Grounded || 
 +| ::: |  Neutral  | Grounded when Neutral Switch Active| 
 +| ::: |  Oil  | Grounded when Oil Pressure Switch has 'Low' Pressure | 
 +| ::: | Neutral & Oil Indicators Always Get Power from Acc Circuit || 
 +| 92-13 |  HiBeam  | Powered from Hi/Lo Switch when on 'HI' | 
 +| ::: |  L. Turn  | Power from Left TS output circuit of TSM | 
 +| ::: |  R. Turn  | Power from Right TS output circuit of TSM | 
 +| ::: | HiBeam & TS Indicators Are Always Grounded || 
 +| ::: |  Neutral  | Grounded when Neutral Switch Active| 
 +| ::: |  Oil  | Grounded when Oil Pressure Switch has 'Low' Pressure | 
 +| ::: | Neutral & Oil Indicators Are Always Powered from Acc Circuit || 
 +| 14-22 |  HiBeam  | \\ Each Indicator is grounded from the Speedometer\\ based on system operations as communicated to\\ the Speedometer from the ECM over the CANbus.| 
 +| ::: |  L. Turn  | ::: | 
 +| ::: |  R. Turn  | ::: | 
 +| ::: |  Neutral  | ::: | 
 +| ::: |  Oil  | ::: | 
 +| ::: | All Indicators are Powered from Always-On Battery Fuse || 
 +| Note: TS means Turn Signal / TSM means Turn Signal Module ||| 
 + 
 +**Bulbs** 
 + 
 +**1986-1991** models used individual Indicator bulbs.\\ 
 + 
 +**1992-1994** models used Indicator Units without replaceable individual bulbs - The entire unit (cylindrical housing with pig tail wires) needs to be replaced.\\
  
 **1995-2006** models used replaceable Indicator Bulbs - P/N 68024-94\\ **1995-2006** models used replaceable Indicator Bulbs - P/N 68024-94\\
Line 497: Line 527:
 The indicator lights are LEDs that are soldered onto a circuit board strip (SMDs). These individual LEDs are activated by the Speedometer, which communicates with the ECM/BCM via the CANbus. The indicator lights are LEDs that are soldered onto a circuit board strip (SMDs). These individual LEDs are activated by the Speedometer, which communicates with the ECM/BCM via the CANbus.
  
-Here is DIY info regarding the repair of faulty indicator lights (2014-later). +Here is DIY info regarding the repair of faulty indicator lights.\\ 
-  * [[techtalk:evo:elec03b|Subdoc - Indicator / Warning Lights Not Working - Repair]]+  * [[techtalk:evo:elec03b|Subdoc - Indicator / Warning Lights Not Working - Repair (2014-later).]] 
 + 
 +An interesting repair in this [[https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/rubber-mount-sportster-motorcycle-talk-2004-2006/202706-repair-of-trim-plate-indicator-lamps-68513-95a?t=2079909|XLForum Thread]] by Krono.
  
 **INDICATOR LIGHTS PARTS LIST** **INDICATOR LIGHTS PARTS LIST**
Line 519: Line 551:
 ^ 2007 Custom Models - LEDs || ^ 2007 Custom Models - LEDs ||
 | | LEDs & Housing part of Harness (68814-07)\\ 68382-07B Trim Plate & Bezel Assy (Symbols/Clear Lense) | | | LEDs & Housing part of Harness (68814-07)\\ 68382-07B Trim Plate & Bezel Assy (Symbols/Clear Lense) |
- 
-An interesting repair in this [[https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/rubber-mount-sportster-motorcycle-talk-2004-2006/202706-repair-of-trim-plate-indicator-lamps-68513-95a?t=2079909|XLForum Thread]] by Krono. 
  
 \\ \\
Line 595: Line 625:
  
 \\ \\
 +
 +**( [[techtalk:evo:engctl03b|SUBdoc - VSS / Speedometer / TSM Control Signals]] )**
  
 **( [[techtalk:evo:elec03g|SUBdoc - BASIC TESTING of Turn Signal Wiring]] )** **( [[techtalk:evo:elec03g|SUBdoc - BASIC TESTING of Turn Signal Wiring]] )**

Trace: