[[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]]
====== REF: HD List of Ironhead Sportster Hardware P/N & Descriptions ======
\\
Below are lists of fasteners known to be used on Sportsters as listed in the factory parts catalogs. \\
This list is not meant to replace the parts catalogs. You should have a full parts catalog that covers your year model bike. \\
The listings below are an attempt to display the year span certain fasteners were used or available, their sizes and to help explain discrepancies in the parts books. \\
In searching screws and bolts in the HD parts catalogs, the following discrepancies can be found. \\
* Some part#s are listed in the older books but never show up being used on anything.
* Some change length (or from course to fine threads) from one book to the next. \\ And then change back to the first length in the next book.
* A few parts books note corrections to previous bolt lengths or models used on.
* Some part numbers are listed as used from year to year. Some are never noted as to when the part was stopped being used.
* Some parts are listed as being used on 54-up models but were not available until many years after the 'used on' beginning date.
* Some fasteners are specific to a kit that may retrofit to earlier models.
* Some fastener changes appear to be related to either availability, cosmetics or material makeup (cad, chrome plated, black etc).
* Some books show a part extending past the end date for that part's use and is corrected in later year parts books.
* Most importantly, the parts books show what parts were available at the time the book was written. \\ If a part had a design change and retro'd to earlier years, the newer parts for the updated one will be shown instead of the original ones. \\ Likewise, occasionally there are part numbers for bolts / screws for the same application. \\ It sometimes depends on if you are using the original or an updated part that may require a shorter or longer fastener than the original part required.
===== Pins =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}||||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|Pic(s)|
|215|1985|Solid Pin|Crankcase Halves Dowel Pin|XL, XLS, XLX|
|219|1952-1971|1/16" x 5/16" Straight Pin|Gear Shifter Pawl \\ Carrier Pin|K Models, \\ Sportsters|
|238|1957-1962|3/32" x 1/2" Straight Pin|
|240|1961-1971|.094" x .488" Solid Dowel Pin|Oil Pump Drive Lock Pin|XL, XLCH|
|255|1952-1965|7/64" x 1/2" Straight Pin|Timer or Magneto Rotor \\ Drive Gear Pin|K Models, Sportsters|
|256|1966-1970|7/64" x 1/2" Roll Pin|Timer or Magneto Rotor \\ Drive Gear Pin|XLH, XLCH|
|:::|1967-1981|:::|Solenoid Shaft Roll Pin #1|XLH|
|271|1952-E1978|1/8" x 1/4" Straight Pin|Cam Cover Bushing Pin|K Models, Sportsters|
|275|1952-1985|1/8" x 1/4" Straight Pin|Cam Cover Bushing Pin \\ (Replaced pin #271 in L1978)|Sportsters|
|327|1952-1957|1/8" x 3/4" Straight Pin|Generator Drive Gear Pin|K Models, XL|
|333|1952-1976|1/8" x 1-3/4" Straight Pin|Crankcase Oil Strainer \\ Retaining Pin|K Models, Sportsters|
|334|1967-1978|1/8" x 3/8" Pin|Starter Housing Pin|XLH|
|350|1952-1985|13/64" x 7/8" Straight Pin|Gear Shifter Pawl Lifter Arm Pin|K Models, Sportsters|
|358|1952-1985|1/4" x 1/2" Dowel Pin|Crankcase Dowel Pin|K Models, Sportsters|
|375|1952-1985|5/16" x 11/16" Straight Pin|Gear Case Cover Dowel Pin|K Models, Sportsters|
|491|L1962-1969|Pin with Head|Tachometer Plug Pin|XLCH|{{ :techtalk:ih:elec:1962l-1965_xlch_tachometer_plug_pin_491_by_animalhouse2010.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, animalhouse2010, [[https://www.ebay.com/str/animalhouse2010?_trksid=p2047675.l2563|Link to Ebay store:]] ))|
|600|1952-E1982|1/8" x 9/16" Roll Pin|Transmission Mainshaft \\ Thrust Washer Pin|K Models, Sportsters|
|:::|1952-1978|:::|Oil Filter Gauge Rod Bushing Pin|K Models, Sportsters|
|:::|1952-1956|:::|Oil Filter Bypass Valve Pin|K Models|
|:::|1967-1981|1/8" x 1/2" Roll Pin|Solenoid Shaft Roll Pin #2|XLH|
|601|1967-1980|1/8" x 3/4" Roll Pin|Solenoid Shaft Roll Pin #2|XLH|
|602|1967-1969|Roll Pin|Indicator Lamp Lens Roll Pin \\ (Replaced pin #603 in 1968)|XLH|
|603|1952-1960|3/32" x 1/2" Roll Pin|Oil Pump Drive Lock Pin|K Models, Sportsters|
|:::|1972-1976|:::|Oil Pump Feed Gear Roll Pin|XLH, XLCH|
|:::|1958 \\ 1959-1976 \\ 1979-1981|:::|Generator Lock / \\ Brush Holder Plate Pin|XLH \\ XLH, XLCH, XLS|
|:::|1967|:::|Indicator Lamp Lens Roll Pin|XLH|
|604|1952-1972|1/8" x 3/8" Roll Pin|Rear Shock Cam Roll Pin|K Models, Sportsters|
|605|1954-1974|Roll Pin|Shifter Lever Shaft Pin|Sportsters|
|:::|1975-1976|:::|:::|XLH, XLCH|
|:::|E1977|:::|:::|XLH, XLCH|
|606|1954-1970|5/64" x 5/16" Roll Pin|Clutch Sprocket Hub Washer Pin|KH, Sportster|
|608|1957-1966|3/16" x 1/2" Roll Pin|Front Chain Cover Roll Pin|XL, XLH|
|609|1952-E1974|Roll Pin|Saddlebag Carrier Plate \\ Support Drive-Loc Pin|K Models, XL, XLH|
|:::|1965-E1974|:::|:::|XLCH|
|612|1967-1969|3/32" x 3/4" Roll Pin|Magneto Adapter Plate Roll Pin|XLCH|
|:::|1954-1970|:::|Kick Start Sprocket Cover Pin|KH, Sportsters|
|614|1967-1981|1/8" x 1" Roll Pin|Solenoid Shaft Roll Pin #3|XL, XLH, XLS|
|615|1971-1979|Roll Pin|Circuit Breaker Plate Roll Pin|XLH, XLCH|
|618|1982-1990|3/16" x 3/4" Roll Pin|Battery Strap Fastener Roll Pin|Sportsters|
|620|1971-1979|Roll Pin|Circuit Breaker Weight Roll Pin|XLH, XLCH|
|621|1971|Roll Pin|Circuit Breaker Plate Roll Pin \\ (replaced by roll pin 623 in '72)|XLH, XLCH|
|623|1971-1979|Roll Pin|Circuit Breaker Plate Roll Pin|XLH, XLCH|
|635|1979|Solid Pin|Timer Weight Pin \\ (use w/ 32625-80)|XL, XLCH, XLS|
|9095|1952-E1984|Roll Pin \\ Dowell Pin|Clutch Gear Bearing Pin, \\ Oil Pump Housing Pin|K Models, Sportsters|
|9220A|1952-E1973|Roller Pin \\ (standard .2498" x .490")|Shift Tower Pins|K Models, Sportsters|
|9260|1954-1985|Dowel Pin|Shift Tower Pin - Cam Support \\ Replaced Pin #9220A (L1973)|KH, XL, XLH, XLCH|
|9260|L1973-1978|Dowel Pin|Handlebar- \\ Control Coil Plunger Roller Pin|XLH, XLCH|
|9261|1957-E1973|.2498" x .600" Solid Pin|Handlebar- \\ Control Coil Plunger Roller Pin|XL, XLH, XLCH|
|24578-57|1957-1985|.555" x .880" Dowel Pin|Trans Trapdoor Dowel Pin|Sportsters|
|24754-75|1977-1996|Dowel Bushing|Primary Cover Dowel Pin|Sportsters|
|26430-76|1977-1985|Pin|Oil Pump Gear Shaft Pin|Sportsters|
|26480-77|1977-1988|Roll Pin|Oil Pump Housing Roll Pin \\ (replaced by 653 in 1989)|Sportsters|
|27164-71|1972-E1976|Roll Pin|Carb Accelerator Pump Roll Pin|XLH, XLCH|
|27308-76|L1976-1987|Solid Pin|Float Pin|XL, XLH, XLCH|
|27338-11|1952-1956|Pin|Carburetor Float Lever Pin|K Models|
|27556-83|L1983-1984|Pin|Carb Accelerator Pump Lever Pin|XR-1000|
|27595-66|1966-1971|Solid Pin|Tillotson Carb Fuel Inlet Lever Pin|XLH, XLCH|
|27631-71|1972-E1976|Solid Pin|Carb Float Pin|XLH, XLCH|
|27665-71|1972-E1976|Solid Pin|Choke Friction Spring Pin|XLH, XLCH|
|30505-47|1952-1970|Pin|Circuit Breaker Pivot Pin|K Models, XL, XLH|
|:::|1970|:::|:::|XLCH|
|32676-64|1965-1970|Pin|Circuit Breaker - Timer Wire Pin|XLH|
|:::|1970|:::|:::|XLCH|
|33086-74|1977-E1979 \\ 1979-1980|Solid Pin w/ Ring Grooves|Kick Starter Crank Arm Pivot Pin|XLCH \\ XL|
|33874-41|1977-1978|Pin|Rear Brake Cable Pin (front)|XL, XLCH|
|34503-52|1952-1971|Pin|Gear Shifter Pawl Carrier Pin|K Models, Sportsters|
|41485-30|1952-1978|3/16" x 7/16" Rivet|Rear Wheel Sprocket Dowel Pin|K Models, Sportsters|
|42269-30|1952-1974|1/4" x 13/16" Pin|Brake Rod Clevis Pin|K Models, Sportsters|
|42269-30|1975-1976|1/4" x 13/16" Pin|Shifter Shaft (splined) Lever Pin|XLH, XLCH|
|42368-79|1979|Pin|Rear Brake Clevis Pin|XL, XLCH, XLS|
|42423-52|1952-1974|Pin|Foot Lever Spring Pin|K Models, Sportsters|{{:techtalk:ref:tools:1952-1974_k_models_-_sportster_foot_lever_spring_pin_42423-52_by_bikersnos.jpg?linkonly|Pic1}} ((photo courtesy of BIKERSNOS.com. [[https://www.ebay.com/str/bikersnos?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] ))|
|42447-80|E1980-1981|Pin|Brake Pedal to Master Cylinder \\ Rod Thru Pin|XL, XLS|
|42460-80A|L1980-E1987|Clevis Pin|Rear Master Cylinder Clevis Pin \\ (use with 515 cotter pin)|Sportsters|
|44124-72|1973|Solid Pin|Brake Pad (slider) Pin|XLH, XLCH|
|44162-77|1978-1983|Solid Pin|Front Brake Caliper Slider Pin|XL, XLCH, XLS, XLX|
|44186-77|1979-1981|Solid Pin|Rear Brake Caliper Slider Pin|XL, XLCH, XLS|
|44280-74|1974-1977|Anchor Pin|Front Brake Upper Anchor Pin|XLH, XLCH|
|44283-74|1974-1977|Anchor Pin|Front Brake Lower Anchor Pin|XLH, XLCH|
|44524-51|1952-1972|Pin with Head|Front Brake Clevis Pin|K Models, Sportsters|
|45031-65|1965-1972|Pivot Pin|Front Brake Lever Pivot Pin|XLH, XLCH|
|:::|1965-1981|Pivot Pin|Clutch Lever Pivot Pin|XLH, XLCH, XLS|
|45031-72|1973-1981|Pin|Front Master Cylinder Plunger Pin|XLH, XLCH, XLS|
|45031-82|1982-1990|Pin|Stoplight Switch and Pushrod Pin|Sportsters|
|45032-72|1973-1981|Pin|Front Brake Hand Lever Pin|XLH, XLCH, XLS|
|45032-82|1982-1990|Pivot Pin|Clutch / Front Brake Lever Pivot Pin|Sportsters|
|45033-49|1954-1964|Anchor Pin|Hand Lever Anchor Pin|KH, Sportsters|
|45033-65|1965-E1968|Anchor Pin|Hand Lever Anchor Pin|XLH, XLCH|
|45034-68|L1968-1978|Anchor Pin|Clutch Lever Anchor Pin \\ (used without bushing)|XLH, XLCH|
|:::|L1968-1972|:::|Brake Lever Anchor Pin \\ (used without bushing)|XLH, XLCH|
|45036-68|1965-1981|Anchor Pin|Clutch Lever Anchor Pin \\ (used with nylon bushing)|XLH, XLCH, XLS|
|:::|1965-1972|Anchor Pin|Front Brake Lever Anchor Pin \\ (used with nylon bushing)|XLH, XLCH|
|45036-82|1982-1988|Anchor Pin|Clutch Lever Anchor Pin|Sportsters|
|45052-75|1975-1978|Pin|Splined Arm to Brake Cable Pin|XLH, XLCH|
|45917-73|1973-1974|Roll Pin|Fork Damper Tube Stop Roll Pin|XLH, XLCH|
|50090-52|1953|Pin|Jiffy Stand Pin|K|
|50090-53|1954-1976|Pin|Jiffy Stand Pin|KH, Sportsters|
|50090-77|1977-E1984|Pin|Jiffy Stand Pin|XL, XLCH, XLS|
|59841-70|1957-1978|Pin|Front Seat Mounting Bracket Pin|XLH, XLCH|
===== Cotter Pins =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|510|1952-1972|1/16" x 1/2" Cotter Pin|Front / Rear Brake Lever Clevis Pin|KH, Sportster|
|510|1952-1965|1/16" x 1/2" Cotter Pin|Linkert Carb Throttle Control Wire Block.|KH, Sportster|
|510|1952-1957|1/16" x 1/2" Cotter Pin|A/C Carb Choke Rod Pin|K Models, XL|
|510 \\ 515|1965-1969|1/16" x 1/2" Cotter Pin \\ 1/16" x 3/4" Cotter Pin|Magneto Control Wire Screw|XLCH|
|510 \\ 515|1966-1969|1/16" x 1/2" Cotter Pin \\ 1/16" x 3/4" Cotter Pin|Lower Oil Tank Bolt Pin|XLCH|
|512|1952-1964|1/16" x 5/8" Cotter Pin|Front Brake Hand Lever Pivot Screw \\ Clutch Lever Clamp Bushing|K Models, Sportsters|
|515|1966-1971|1/16" x 1/2" Cotter Pin|Carb Throttle Shaft Wire Block Pin|XLH, XLCH|
|:::|1952-1972|:::|Front Brake Lever Clevis Pin (1976)|K Models, Sportster|
|:::|1952-1974|1/16" x 3/4" Cotter Pin|Rear Brake Lever Clevis Pin|K Models, Sportster|
|:::|1965-1969|:::|Magneto Wire Block Spring Pin|XLCH|
|:::| Parts catalogs discrepancies on the length of this pin||||
|:::|1966-1969|1/16" x 3/4" Cotter Pin|Lower Oil Tank Bracket Bolt Pin|XLCH|
|:::|L1980-1990|:::|Rear Master Cylinder to \\ Pedal Clevis Pin|Sportsters|
|528|1952-1967|3/32" x 5/8" Cotter Pin|Oil Tank Cap Cotter Pin|K Models, Sportsters|
|534|1954-1967|3/32" x 1" Cotter Pin|Footrest Support Stud|KH, XLH|
|:::|1965-1969|:::|:::|XLCH|
|:::|1954-1978 \\ 1965-1978|:::|Oil Tank Cap Cotter Pin|KH, XL, XLH \\ XLCH|
===== Rivets =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|8214|1952-1970|5/32" x 7/16" \\ Countersunk Head Rivet|Clutch Sprocket Key|K Models, Sportsters|
|8215|1952-1970|5/32" x 3/4" \\ Countersunk Head Rivet|Clutch Sprocket Hub|K Models, Sportsters|
|8215|1957-1970|5/32" x 13/16" x 9/32" \\ Countersunk Head Rivet|Clutch Sprocket Hub|XL, XLH, XLCH|
|8215|1957-1976|:::|Starter Ratchet Rivet \\ (from ratchet and \\ gear kit 33400-74, 57-70)|XL, XLH, XLCH|
|8216|1954-1955|5/32" x 3/8" \\ Countersunk Head Rivet|Rear Shock Cam Rivet|KH|
|8216|1971-E1979|5/32" x 7/16" x 9/32" \\ Countersunk Head Rivet|Starter Ratchet to Clutch Sprocket|XLCH|
|:::|1979-1980|:::|:::|XL, XLS, XLH|
|8219P|1966-1971|Rivet|Dual Seat Trim Strip Rivet|XLH, XLCH|
|8241|1952-1978|3/16" x 5/8" x 11/32" \\ Countersunk Head Rivet|Kick Starter Crank Cam Plate|K Models, Sportsters|
|8243|1952-1956|3/16" x 7/8" \\ Countersunk Head Rivet|Motor Sprocket|K, KH|
|8303|L1975-E1977|Rivet|Hazard Flasher Clip Rivet|XLH, XLCH|
|8306|1982|Rivet|Chain Guard Scuff Pad Rivet|XL, XLS|
|8331|1962-1964|3/16" x 5/16" Tubular Rivet|Generator Brush Holder Plate Rivet|XLH, XLCH|
|8475|1974-1977|9/64" x 9/32" Brass Rivet|Front Brake Lining Rivet|XLH, XLCH|
|8479|1974-1977|Rivet|Brake Lining Rivet|XLH, XLCH|
|8483|1973-E1974 \\ 1979-1985|3/16" x 7/16" x 5/8" Pop Rivet|Circuit Breaker Clip Rivet|XLH, XLCH, XLS|
|:::|1979-1990|:::|Rear Fender Splash Guard Rivet|XL, XLCH, XLS|
|8485|1954-1970|Rivet|Rear Wheel Sprocket Rivet|KH, Sportsters|
|8486|1954-1978|1/8" x 9/16" x 1/4" \\ Round Head Rivet|Rear Wheel Sprocket Rivet \\ (Replaced Rivet #8485 in 1971)|KH, Sportsters|
|8515|1965-1970|3/16" x 3/8" Truss Head Rivet|Seat Bar Clamp Plate Rivet|XLCH|
|8519|L1977-1978 \\ L1973-1985|Rivet|Hazard Flasher Clip Rivet \\ Turn Signal Flasher Rivet|XL, XLCH \\ XLH, XLCH, XLS|
|8528W|1973-1975|3/16" x 3/8" x 3/8" \\ Pop Rivet (steel)|Hazard Flasher Clip Rivet|XLH, XLCH|
|8685|1984-1985|Rivet|Splash Guard to Fender \\ Extension Rivet|XL, XLS, XLX|
|8687|1973-|Pop Rivet|Turn Signal Clip|XLH, XLCH|
|8692|L1975-E1977|5/32" x 3/8" x 5/16" Pop Rivet|Turn Signal Flasher Rivet|XLH, XLCH|
|:::|1979-1985|(reused in 1984 for 1979-1984 models)|||
|8699|1980-1990|3/16" x 3/8" x 3/8" Pop Rivet|Ignition Module Cover Rivet|Sportsters|
|27045-32|1952-1956|3/16" x 7/16" Rivet|Intake Nipple Rivet|K, KH|
|:::|:::|1/4" x 7/16"|:::|:::|
|41841-31|1952-1972|1/8" x 1/4" Tubular Rivet|Brake Lining Rivet|K Models, Sportsters|
|61795-57|1957|Rivet|Name Plate Rivet|XL|
|71859-29|1954-1972|Pin|Light Switch Contact Pin (2 position)|KH, XL, XLH|
|:::|1963-1972|:::|:::|XLCH|
|71859-38A|1954-1972|Pin|Light Switch Contact Pin (3 position)|KH, XL, XLH|
|:::|1963-1972|:::|:::|XLCH|
|90965-63|1966-1978|Rivet 5/16" long|Saddlebag Clip Rivet|XLH, XLCH|
|90967-64|1966-1978|Rivet 3/8" long|Saddlebag Clip Rivet|XLH, XLCH|
===== Retainers / Rings / Clips / Circlips / Clamps =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|575|1967-1971|Hairpin Clip|Choke Cable Tube Pin|XLH, XLCH|
|7410|1952|5/16" Tabbed Lock Washer|Shift Lever Stop Bolt|K|
|9952|1973-1985|Bracket|Circuit Breaker Holder Clip|Sportsters|
|:::|1979-1985|:::|Turn Signal Flasher Holder Clip|Sportsters|
|:::|1982-1990|:::|Rear Fender Clip|Sportsters|
|9954|1957-1972|Holder Bracket|Flasher Clip \\ (Flasher Kit (68541-68)|XLH|
|:::|1970-1972|:::|:::|XLCH|
|9954|L1983-1984|Worm Band Clamp \\ (1.312"-2.250")|Intake Sleeve to Carb Clamp|XR-1000|
|9957|1961-1970|Cable Coil Clamp|Circuit Breaker Coil Clamp|XLH|
|:::|1957-1978|:::|Choke Control Spring Clamp|XL|
|:::|1974-1978|:::|Spark Coil Cable Clip|XLH|
|:::|L1966-1978|:::|Siren Cable Clamp|XLH|
|9958|1965-1969|Clamp|Magneto Cable Clip on crankcase \\ stud (Replaced by 67075-57A \\ in '66)|XLCH|
|9958|1967-1969|Clamp|Rear Turn Signal Wire Clamp|XLH|
|9961|L1962-1973|Small Spring Clip|Tach Cable Clip|XLCH|
|:::|1968-1978|:::|Front Fender Lamp Kit (59260-68) \\ Fender Lamp Cable Clip|XLH|
|:::|1970-1978|:::|:::|XLCH|
|9963|1059-1962|Cable Clip|Fuse Holder Clip|XLCH|
|:::|1965-1969|:::|Tach Cable to Frame Clip|XLCH|
|9965|1961-1970|Cable Clip|Throttle Cable Coil Clamp|XLH, XLCH|
|9965W|1961-1972|Cable Clip|Throttle Cable Coil Clamp|XLH, XLCH|
|:::|1954-1978|Cable Clip|Winter Windshield Apron Clip|KH, XL, XLH, XLCH|
|:::|1973-1978|:::|Tail Lamp Stud Clip|XLH, XLCH|
|9976|1957-E1973|Spring Clip|Handlebar Switch Cable Clip|XL, XLH|
|:::|1968-1978|:::|From Ammeter Kit (74440-68) \\ Spring Clip|XLH, XLCH|
|:::|1954-1966|:::|Spotlight Wire Clamp|KH, XL, XLH|
|9977|1957-1963|Cable Clip|Frame Cable Clip \\ Replaced by 10012 Clip|XL, XLH|
|9982|1954-1965|Cable Clip|Speedo/Tach Cable Clip|KH, Sportsters|
|:::|1970-1971|:::|BoatTail Taillight Cable Clip|XLH, XLCH|
|9983|1961-1978|Cable Clip|Tube Type Cable Guide|XLH|
|:::|1959-1973|:::|Speedometer Cable to Frame Clip|XLCH|
|9986|1968-1978|Large Spring Clip|Front Fender Lamp Kit (59260-68) \\ Fender Lamp Cable Clip|XLH|
|9989|1954-1956|Cable Clip|Circuit Breaker coil Clamp|K Models|
|9990W|1974-1977|Clip|Front Brake Hose (fork) Clip|XLH, XLCH|
|9994|1957-1965|Cable Clip|Magneto Cable Clip \\ (Replaced by 67075-57A in 1966)|XLCH|
|9998|L1956-E1966|Spring Type Hose Clamp \\ (7/16" O.D.)|Gas Hose / Vent Clamp|KH, XL, XLH|
|:::|1963-E1966|:::|:::|XLCH|
|10001|1954-1966|:::|Spotlight Cable Clamp|KH, XL, XLH|
|:::|1957-E1973|Cable Clip|Handlebar Switch Cable Clip|XL, XLH|
|:::|1970-E1973|:::|:::|XLCH|
|10012|1957-E1973|Cable Clamp|Frame Cable Clamp \\ Replacement for #9977 Clip|XLH|
|10013|L1961-1968|5/8" Crimp Style Band Clamp \\ (Replaced by 10020 in '69)|Oil Tank Feed & Return Hose|XLH, XLCH|
|10014|L1961-1985|1/2" Crimp Style Band Clamp|Oil Tank Vent Hose Clamp|XLCH|
|:::|1966-1985|:::|Gas Tank Hose Clamp|XLH, XLCH, XLX|
|:::|1979-1982|:::|:::|XLS|
|:::|1977-1978|:::|Gearcase Breather Pipe Clamp|XLH, XLCH|
|:::|1979-1985|:::|Gearcase, Oil Tank Vent Hose|XL, XLCH, XLS, XLX|
|10020|L1961-1982|11/16" Crimp Style Band Clamp|Feed and Return Oil Line Clamp|XLH, XLCH|
|:::|1979-1982|:::|Gearcase Breather Hose Clamp|XL, XLCH, XLS|
|10020A|1983-1985|11/16" Crimp Style Band Clamp|Feed and Return Oil Line Clamp|XLH, XLCH, XLS, \\ XLX, XR-1000|
|:::|1979-1985|:::|Gearcase Breather Hose Clamp|XL, XLCH, XLS, XLX|
|:::|L1983-1984|:::|Head Drain Hose Clamp|XR-1000|
|10040|L1983-1984|Clip|Passenger Footrest Hole Clip|XR-1000|
|11000|1957-1978|E-Clip Ring|Seat Pin Ret Ring|XLH, XLCH|
|11002|1956-E1962|13/32" External Circlip ((https://www.mcmaster.com/external-retaining-rings/external-retaining-rings-7/)) |Oil Pump Shaft / Breather Gear|KH, Sportsters|
|:::|1972-1976|:::|:::|XLH, XLCH|
|:::|(ID .366", thickness .025", fits groove size .382")||||
|11004|1954-1957|Internal Circlip|Generator Oil Ring Ret|KH, XL|
|:::|1954-1958|:::|Generator Bearing Ret Ring|KH, XL, XLH|
|:::|1959-1981|:::|:::|XLH, XLCH, XLS|
|:::|Replaced #30146-46 in 1963 for 58 XLH and 1959-up XLH, XLCH with new seals||||
|11005|1971-E1984|External Circlip|Clutch Adjuster Screw Ret Ring|Sportsters|
|11006|L1979|Inverted External Circlip|Mainshaft Ball Bearing \\ (outer) Ret Ring|XLCH|
|11012|L1966-1978|E-Clip Ring|Oil Tank Cap Ret Ring|XLH|
|11015|1973-1981|Heavy Duty E-Clip Ring|Front Brake Lever \\ Pivot Pin Ret Ring|XLH, XLCH, XLS|
|11016|1975-1976|External Circlip|Shifter Link Ret Ring|XLH, XLCH|
|11024|L1962-1969|Spring Clip|Tachometer Plug Pin|XLCH|
|11027|1979-1981 \\ 1979-1985|Internal Circlip|Cast Rear Wheel \\ Hub Bearing Ret \\ Laced Rear Wheel \\ Hub Bearing Ret|XL, XLCH, XLS \\ XL, XLCH, XLS , XLX|
|11031|1977-E1979 \\ 1979-1980|External Circlip|Kick Starter Crank Pivot Pin|XLCH \\ XL|
|11035|1964-1972|Internal Circlip|Front Wheel Hub Ret Ring|XLH, XLCH|
|11036|1965-1981|E-Clip|Clutch Lever Pivot Pin Ret Ring|XLH, XLCH|
|:::|1965-1972|:::|Front Brake Lever Pin Ret Ring|XLH, XLCH|
|:::|1972-1985|:::|Shifter Pawl Ret Ring|Sportsters|
|11039|1967-1980|Inverted External Circlip|Starter Shaft Ret Ring|XL, XLH, XLS|
|11045|L1984-1985|Inverted External Circlip|Guide Bearing Ret Ring|XL, XLS, XLX|
|11046|L1984-1985|External Circlip|Clutch Adjusting Screw Ret Ring|XL, XLS, XLX|
|11047|1968-E1972|Inverted External Circlip|Damper Tube Tube Ret Ring|XLH, XLCH|
|11047|L1984-1986|Inverted External Circlip|Mainshaft Ball Bearing \\ (outer) Ret Ring|Sportsters|
|11048|1968-1972|Balanced Lug Internal Circlip|Slider Tube Ret Ring|XLH, XLCH|
|11049|L1967-1970|Retaining Ring|Oil Filter Ret Ring|XLH|
|11052|1971-E1984|Internal Circlip|Clutch Bearing Ret Ring|Sportsters|
|11053|1971-E1984|Round Wire Snap Ring|Clutch Outer Drive Plate Ret|Sportsters|
|11063|1973-1981|Internal Circlip|Front Master Cylinder \\ Piston Ret Ring|XLH, XLCH, XLS|
|:::|L1980-1981|:::|Rear Brake Pedal \\ Clevis Pin Ret Ring|XL, XLS|
|11065|L1972|External Circlip|Damper Tube Tube Ret Ring|XLH, XLCH|
|11093|1980-1990|Inverted External Circlip|Right Footpeg Ret Ring|Sportsters|
|11143|1982-1985|External Circlip|Clutch Lever Pivot Pin Ret Ring|XL, XLS|
|11143|1982-1990|External Circlip|Brake Lever Pivot Pin Ret Ring|Sportsters|
|11155|1979-1990|Retaining Ring|Throttle Adjusting Screw Kit \\ (56397-83)|Sportsters|
|11164|L1984-1985|External Circlip|Clutch Hub Bearing Ret Ring|XL, XLS, XLX|
|24701-52|1952-1976|Constant Section Snap Ring|Sprocket Shaft Bearing Ret Ring|K Models, Sportsters|
|24701-54|1954-1976|Split Ring|Gear Shaft Bearing Ret Ring|KH, Sportsters|
|26341-37|1954-1956|Half Ring (2)|Breather Valve Ret|KH|
|:::|L1962-1971|:::|:::|Sportsters|
|26497-75|1977-1990|1/2" Inverted External Circlip|Oil Pump Shaft Ret Ring|Sportsters|
|:::|(DIN 471 specs, ID .461", thickness .035", fits groove size .468")||||
|27338-76|L1976-1985|Clip|Carb Fuel Valve Clip|XLH, XLCH|
|27368-76|L1976-2006|Clip|Carb Bowl Overflow Hose Clip|Sportsters|
|27574-83|L1983-1984|Retaining Ring|Carb Metering Rod Retaining Ring|XR-1000|
|27716-55|1967-1971|Crimp-On External Retainer Clip|Carb Choke Wire Block Clip|XLH, XLCH|
|27737-71|1972-E1976|Clip|Carb Fuel Valve Clip|XLH, XLCH|
|29620-55|1958-1969|Spring Clip|Breaker Arm Clip|XLCH|
|29621-55|1958-1969|Internal Circlip|Rotor Shaft End Snap Ring|XLCH|
|29622-55A|1958-1969|Spring Clip|Rotor Shaft End Spring Clip|XLCH|
|29648-62|L1962-1969|Special E-Clip|Magneto Ground Lock Ret Clip|XLCH|
|30146-46|1952-1962|Internal Circlip|Armature Felt Washer Ret|K Models, Sportsters|
|:::|Replaced by #11004 in 1963 for 58 XLH and 1959-up XLH, XLCH with new seals||||
|31017-29|1953-1957|1-5/16" Wire Snap Ring|Brush End Bearing Ret Ring|K Models, XL|
|31096-58|1958|Clip|Generator Terminal Bolt Clip|XLH|
|:::|1959-1981|:::|:::|XLH, XLCH, XLS|
|31473-67|1967-1976|Clamp|Starter Motor Clamp|XLH|
|32585-36|1952-1964|Spring Retainer|Circuit Breaker Base Ret|K Models, XL, XLH|
|32592-36|1954-1964|Retainer|Circuit Breaker Cover Ret|KH, XL, XLH|
|34040-52|1952-1985|External Circlip|Trans Shifter Cam Ret Ring|K Models, Sportsters|
|34065-52|1952-1985|Special Bolt|Cam Follower Spring Ret|KH, XL, XLH, XLCH|
|34067-52|1952-1985|Tabbed Lock Washer|Shifter Cam Lock|K Models, Sportsters|
|34069-71|1955-1985|Tabbed Lock Washer|Shifter Cam Bolt Lock|KH, Sportsters|
|34897-53|1953-1970|Load Retainer Arm|Clutch Cover Screw Ret|KH, Sportsters|
|35112-52|1952-E1984|Constant Section Snap Ring|Mainshaft Ball Bearing Ret|K Models, Sportsters|
|35112-84|L1984-1985|Constant Section Snap Ring|Mainshaft Ball Bearing Inner Ret|XL, XLS, XLX|
|35113-52|1952-E1984|Constant Section Snap Ring|Mainshaft Roller Bearing Ret|K Models, Sportsters|
|35154-52|1979-1983|Retainer|Mainshaft Oil Seal Ret|XL, XLCH, XLS|
|35337-52|1952-1955|Constant Section Snap Ring|Mainshaft 3rd Gear Ret Ring|K Models|
|35337-56|1956-1990|Constant Section Snap Ring|Mainshaft 3rd Gear Ret Ring|KH, Sportsters|
|36712-42|1952-1964|Straight Cable Compression Clamp \\ (used w simple coiled cable)|Clutch Cable End|K Models, Sportsters|
|36795-84|L1984-1985|External Circlip|Clutch Hub Ret Ring|XL, XLS, XLX|
|36797-84|L1984-1985|Constant Section Retaining Ring|Clutch Pressure Plate Ret Ring|XL, XLS, XLX|
|36798-84|L1984-1985|Constant Section Retaining Ring|Clutch Hub Ret Ring|XL, XLS, XLX|
|37080-41|1955-1970|Tabbed Lock Washer|Shifter Cam Bolt Lock|KH, Sportsters|
|38659-67|1967-E1969|Cable Guide|Clutch Cable Guide \\ (mounted on fork rear panels)|XLH|
|38660-56|1956-E1969|Double Coil Ended Wire|Cable Guide|KH, Sportsters|
|38646-51|1952-1970|"T" Type Cable Compression Clamp \\ (for 38663-52 Seal Ret Sleeve)|Clutch Cable End|K Models, Sportsters|
|38663-52|1952-1970|Retainer Sleeve|Clutch cable Felt \\ Seal Ret Sleeve|K Models, Sportsters|
|38712-68|1973-1977|Clip|Front Brake Hose Clip \\ (mounted on fender)|XLH, XLCH|
|41768-73|L1973|Clip|Vibration Damper Clip|XLH, XLCH|
|42269-30|1975-1976|Pin|Shifter Link Pin|XLH, XLCH|
|42281-35A|1967-1974|Clip|Brake Switch Clip|XLH, XLCH|
|42369-79|1979-1981|E-Clip Ring|Rear Brake Clevis Pin Ret Ring|XL, XLCH, XLS|
|42400-79|1979|Clip|Rear Brake Return Spring Clip|XL, XLCH, XLS|
|42585-75|1975-1976|Pivot|Shifter Link Pivot End|XLH, XLCH|
|44021-83|1984-1990|Round Wire Snap Ring|Brake Caliper Piston Ret Ring|Sportsters|
|44128-72|1973|External Circlip|Front Brake Caliper Ret Ring|XLH, XLCH|
|45109-49|1952-1972|Wire Ferrule|Front Brake Lever Wire Ferrule|K Models, Sportsters|
|45174-51|1952-1963|Clevis|Brake Cable Clevis|K Models, Sportsters|
|45174-64|1964-1972|Clevis|Brake Cable Clevis|XLH, XLCH|
|45401-75|1975-1983|Internal Circlip|Fork Oil Seal Ret Ring|XLH, XLCH, XLS, XLX|
|45908-80|1975-1987|Round Wire Wave Ring|Fork Oil Seal Ret Ring \\ (Replaced 45401-75 in 1984)|Sportsters|
|45931-73|1973-1974|Round Wire Snap Ring|Fork Slider Oil Seal Ret Ring|XLH, XLCH|
|45932-73|1973-1974|External Circlip|Fork Damper Tube \\ Upper Ret Ring|XLH, XLCH|
|45979-73|1973-1974|Internal Circlip|Fork Damper Tube \\ Piston Ret Rinf|XLH, XLCH|
|46160-71|1971-1972|Retainer|Fork Damper Tube Ret Ring|XLH, XLCH|
|52117-61 \\ 52117-61A|1952-1965|Clip|Dual Seat Front Bracket Clip|K Models, Sportsters|
|:::|1970-1978|:::|:::|XLH, XLCH|
|52117-61A|1970-1971|Clip|Seat Bracket Clip (front)|XLH, XLCH|
|54670-67|1967-1974|Retaining Ring|Rear Shock Upper Spring Ret|XLH, XLCH|
|56062-73|1979-1980|Round Wire Clip|Handlebar Wire Clip|XL, XLCH, XLS|
|56070-81|1981-1983|Clip|Handlebar Wire Clip|XL, XLS|
|56073-83|1983-1985 \\ 1985|Clip|Handlebar Wire Clip|XLX \\ XL, XLS|
|61546-74|1980-1981|Clip|Gas Tank Mounting Clip|XLS|
|61797-57|1957|Clip (resembles drywall screw insert)|Rivet Clip|XL|
|62150-50|1952-1969|E-Clip Ring|Gas Valve Knob Retainer Ring|K Models, XL, XLH|
|:::|1965-1969|:::|:::|XLCH|
|:::|1965-1966|:::|Circuit Breaker Timer Weights Ret|XLH|
|63878-53|1952-1978|Clip|Oil Filter Clip|K Models, XL, XLH|
|67075-57A|1965-1969|Cable Clip|Mag Cable Clip-Crankcase Stud \\ (replaced 9958, 9994 in '66)|XLCH|
|67086-52|1954-1958|Clip|Speedometer Cable Clip|KH, XL, XLH|
|67714-63|1963|Spring Steel Retainer|Spring Terminal Ret|XLCH|
|68539-61|1957-1966|Screws and Screw Clips|Three Terminal Hazard Flasher Kit|XL, XLH|
===== Shaft Keys =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|11200|L1979|Key - 3/16" wide x 1/2" long ((TSB M-829 dated May 19, 1981))|Gearshaft Key \\ Sprocket Shaft Key|XL, XLS|
|11204|1980-1985|Key|Rear Intake Cam Gear Key|XL, XLS, XLX|
|11218|L1981-1985|Key - 1/8" wide x 3/8" long ((TSB M-829 dated May 19, 1981))|Crankpin and Gearshaft Key|XL, XLS, XLX|
|25860-29|1954-1956|Key|Circuit Breaker Drive Gear Key|KH|
|:::|1972-1976|:::|:::|XLH, XLCH|
|23985-12|1952-E1954|Key - 3/16" wide X 1/2" long ((TSB M-829 dated May 19, 1981)) |Flywheel Sprocket Shaft Key|K Models|
|:::|1957-E1981|:::|Flywheel Gearshaft Shaft Key|Sportsters|
|:::|L1954-E1981|:::|Flywheel Sprocket Shaft Key \\ (Replaced #40390-54 in 1972)|KH, Sportsters|
|23985-18|L1954-1956|Key - 1/8" wide X 1/2" long ((TSB M-829 dated May 19, 1981))|Flywheel Sprocket Shaft Key|K Models|
|:::|1957-E1981|:::|Crankpin Key|Sportsters|
|26340-36|1960-1971|Key|Breather Valve Gear Key|Sportsters|
|26341-37|L1962-1971|Key|Breather Valve Gear Half Key|Sportsters|
|26347-15|1953-1959|Key|Breather Valve Gear Key|K Models, Sportsters|
|26348-15|1972-1976|Key|Breather Valve Gear Key|XLH, XLCH|
|40390-54|L1954-1971|Key|Flywheel Sprocket Shaft Key \\ (Replaced by #23985-12 in 1972)|KH, Sportsters|
|90906-52|1952-1965|Hairpin|Saddlebag Support Clip|K, KH, XL, XLH|
|:::|1965|:::|:::|XLCH|
|:::|1975-1976|:::|Shifter Link Pin Clip|XLH, XLCH|
===== Plugs / Drain Plugs =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}||||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|Pic(s)|
|652|1980-1983|3/8" Metal Welch Plug|Crankpin Plug|XL, XLS|
|662|1958-1965|3/8" x 1/2" Allen Head Plug|Gas Tank Drain Plug|XLC, XLCH|
|704|1958-1961 \\ 1966-1978 \\ 1979-1981|5/8" x 18 x 3/8" Plug w/ \\ 3/4" Hex Head|Oil Tank Drain Plug|XLCH \\ \\ XLH, XLCH, XLS|{{:techtalk:ref:oil:fitting_704_timing_hole-oil_drain_plug_704_by_sum-body1_pic1.jpg?linkonly|Pic1}} ((photo courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] ))\\ {{:techtalk:ref:oil:fitting_704_timing_hole-oil_drain_plug_704_by_sum-body1_pic2.jpg?linkonly|Pic2}} ((photo courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] ))|
|:::|1954-1971|:::|Timing Hole Plug|KH, Sportsters|:::|
|706 \\ 706A|1982-1983 \\ 1984-1985|1/2" x 20 x 1/2" Plug w/ \\ 7/8" Hex Head|Oil Tank Drain Plug|XL, XLS, XLX| \\ {{ :techtalk:ref:oil:fitting_706a_oil_tank_drain_plug_by_sum-body1_pic1.jpg?linkonly |Pic2}} ((photo courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] ))|
|707|1952-1978|1/2" x 13 x 3/8" Plug w/ \\ 5/8" Hex Head|Oil Tank Drain Plug|K Models, XL, XLH|{{ :techtalk:ref:oil:fitting_707_drain_plug_by_57harleyrider.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] ))|
|:::|1952-1978|:::|Transmission Drain Plug|K Models, XL, XLH|:::|
|:::|1967-1976|:::|:::|XLCH|:::|
|711|1966-1971|Welch Plug|Carb Body Plug|XLH, XLCH|
|712|1966-1971|Welch Plug|Carb Choke Lever Plug|XLH, XLCH|
|713|1966-E1970|Welch Plug|Carb Check Ball Plug|XLH, XLCH|
|720|1972-2003|5/8" x 18 x .350" \\ Metal Plug w/ \\ 3/8" Hex Socket Head|Timing Hole Plug|Sportsters|{{:techtalk:ref:oil:fitting_720_timing_hole_plug_by_sum-body1_pic1.jpg?linkonly|Pic1}} ((photo courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] )) \\ {{:techtalk:ref:oil:fitting_720_timing_hole_plug_by_sum-body1_pic2.jpg?linkonly|Pic2}} ((photo courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] ))|
|2506|L1981-E1984|7/16" x 14 x 1/2" \\ Allen Socket Head Screw|Gearcase Cover Plug|XL, XLS, XLX|{{ :techtalk:ih:engmech:1981l-e1984_sportster_cam_cover_shaft_hole_plug_2506_by_morlel32.jpg?linkonly |Pic1}} ((photo courtesy of C & M Sales, [[https://www.ebay.com/str/everythingmotorcycleparts?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] ))|
|10040|1983-1988|Plastic Plug|Swingarm Plug|Sportsters|
|16825-48|1952-1976|7/16" Expansion Plug|Shifter Shaft Plug|K Models, Sportsters|{{ :techtalk:ih:transfinal:1952-1976_k-sportster_shifter_shaft_plug_16825-48_by_jrsvintageharley1990.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, jrsvintageharley1990. [[https://www.ebay.com/str/jrsvintageharleyparts?_trksid=p2047675.l2563|Link to Ebay Store]] ))|
|17949-83|L1983-1984|Hex Head Plug|Valve Adjusting Hole Plug|XR-1000|
|24575-52|1958-1972|11/16" x 20 Hex Head Plug|Speedometer Hole - Case Plug|XLC, XLCH|{{ :techtalk:ih:elec:1958-1972_xlch_speedometer_hole_plug_24575-52_by_57harleyrider.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] ))|
|24576-52|1952- |Straight Solid Metal Plug|Right Crankcase Oil Hole Plug|K Models, Sportsters|
|24577-68|1968-1980|Metal Plug|Kicker Shaft Hole Plug|XL, XLH, XLS|{{ :techtalk:ref:oil:fitting_24577-68_kicker_hole_plug_by_57harleyrider.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] )) \\ {{ :techtalk:ref:oil:fitting_24577-68_kicker_hole_plug_by_74_xlh_winchester_va.jpg?linkonly |Pic2}} ((photo by 74_XLH_WINCHESTER_VA of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/90145-kicker-install-on-a-74-xlh?threadid=727978))|
|:::|HD genuine replacement plug is knurled on the outside.||||:::|
|25221-77|1977-1978 \\ 1979-E1981|Rubber Plug|Gearcase Cover Bumper Stem|XLCR \\ XL, XLS|{{ :techtalk:ih:engmech:1977-e1981_cam_cover_rubber_plug_25221-77_by_robison_motorcycles.jpg?linkonly |Pic}} ((photo courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|26420-57|1957-1976|Adapter Fitting|Oil Pressure Switch Fitting|Sportsters|
|27325-33|1952-1965|Plug|Linkert Carb Idle Passage Plug|K Models, Sportsters|
|27326-54|1954-1956|#9 Plug|Carb Metering Plug|KH|
|27327-24|1953-1956|Plug|Carb Passage Plug|K Models|
|27327-52|1953|#7 Plug|Carb Metering Plug|K|
|27328-52|1953|Plug|Carb Idle Bleed Plug|K|
|27328-54|1954-1956|Plug|Carb Idle Bleed Plug|KH|
|27377-39|1952-1956|Fillister Head Screw|Carburetor Drain Plug|K Models|
|27377-57|1957-1965|Fillister Head Screw|Carburetor Drain Plug|Sportsters|
|27385-76|L1976-1987|Plug|Low Speed Jet Plug|Sportsters|{{ :techtalk:ih:carb:1976l-1987_sportster_low_speed_jet_plug_27385-76_by_robisonmotorcycles.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|27704-61|1966-1971|Brass Plug Screw|Carb Main Orifice / Jet Plug|XLH, XLCH|
|27763-71|1972-E1976|Plug|Carb Bowl Drain Plug|XLH, XLCH|{{ :techtalk:ref:tools:1972-e1976_sportster_carburetor_bowl_drain_plug_by_robison_motorcycles.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|27812-66|1966-1971|Plug Screw|Carb Diaphragm Cover Plug|XLH, XLCH|{{:techtalk:ref:tools:1966-1971_sportster_carb_diaphragm_cover_plug_screw_27812-66_by_robison_motorcycles.jpg?linkonly|Pic1}} ((photos courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|34485-52|1952-1985|Plug|Pawl Carrier Spring Ret Plug|K Models, Sportsters|
|34503-52|1952-1971|Shouldered Pin|Pawl Carrier Pin|K Models, Sportsters|
|35631-54|1954-1972|Plug|Countershaft Oiler Plug|KH, Sportsters|{{ :techtalk:ih:transfinal:1954-1972_sportster_transmission_countershaft_oiler_plug_35631-54_by_57harleyrider.jpg?linkonly |Pic1}} ((photos courtesy of Ebay sellers, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] and Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|35631-73|1973-E1984|Plug|Countershaft Oiler Plug|Sportsters|{{ :techtalk:ref:transfinal:1973-e1984_sportster_trans_countershaft_oiler_plug_35631-73_by_57harleyrider.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] ))|
|34485-52|1979-1990|Plug|Shifter Carrier Spring Retainer Plug|Sportsters|
|34742-77B|1979-1985|Threaded Cap|Trans Filler & Clutch Adj Cap|Sportsters|
|37880-71|1971-1976|Plug|Clutch Adjusting Hole Plug|XLH, XLCH|
|45830-48|1958-1976|1/8" x 27 NPT Pipe Plug|Oil Pressure Switch Nipple Plug \\ (in place of pressure switch)|XLCH|{{ :techtalk:ref:oil:fitting_45830-48_drain_plug_by_d_s_cycle_connection.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, D's Cycle Connection [[https://www.ebay.com/str/dscycleconnection?_trksid=p2047675.l2563|Link to Store]] ))|
|:::|1957-1985|:::|Rocker Arm Cover Plug|Sportsters|:::|
|:::|1962-1965|:::|Oil Tank Drain Plug|XLCH|:::|
|:::|1969|:::|Oil Pump Body Plug \\ (Replaced #45831-48 in 1969)|XLCH|:::|
|:::|1977-1985|:::|Scavenge Port Rifling Hole Plug \\ (under sump)|:::|:::|
|:::|1979-1985|:::|Cam Cover (bottom) Plug \\ (plugs rifling hole for oil feed)|XL, XLCH, XLS, XLX|:::|
|45831-48|1967-1968|Plug|Oil Pump Body Plug \\ (Replaced by #45830-48 in 1969)|XLCH|
|45913-80|1980-1981|Bolt|Fork Drain Bolt|XL, XLS|
|45996-73|1973-1980|Drain Screw|Fork Slider Drain Screw|XLH, XLCH, XLS|{{ :techtalk:ref:tools:1973-1980_sportster_fork_slider_drain_screw_by_robison_motorcycles.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] and Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|46201-52|1952-1967|Drain Screw|Fork Slider Drain Plug|K Models, Sportsters|{{ :techtalk:ref:tools:1952-1967_and_1971-1972_k_models_sportster_fork_slider_drain_plug_by_robisonmotorcycles.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|:::|1971-1972|:::|:::|XLH, XLCH|:::|
|53413-69|1954-1978|Plug|Luggage Rack End Plug|KH, XL, XLH, XLCH|{{:techtalk:ref:tools:1954-1978_kh-sportster_luggage_rack_end_plug_53413-69_by_jrsvintageharley1990.jpg?linkonly|Pic1}} ((photo courtesy of Ebay seller, jrsvintageharley1990. [[https://www.ebay.com/str/jrsvintageharleyparts?_trksid=p2047675.l2563|Link to Ebay Store]] ))|
|56238-62|1962-E1983 \\ L1983-1984|Plug|Handlebar Grip Plug|XLH, XLCH, XLS \\ XR-1000|
|:::|1968-1978|Plug|Starter Shaft Hole Plug|XLH|
|56410-53|1954-1973|Plug|Control Coil Plug|KH, Sportsters|
|60348-65|1967-1980|1/2" x 20 Magnetic Plug|Trans Drain Plug (-72)|XLH|
|:::|1970-1979|:::|:::|XLCH|
|60348-65A|1980-1985|1/2" x 20 Magnetic Plug|Trans Drain Plug|Sportsters|
|60965-83|1983- |Plug|Gas Tank Tunnel Plug|XLX|
|66015-47|1952-1964|Plug|Battery Filler Plug|K Models, XL, XLH|
|66016-65|1967-1972|Plug|Battery Filler Plug with Washer|XLH|
|66016-73|1973-1978|Plug|Battery Filler Plug with Gasket|XLH|
|67830-59|1959-1988|Plug|Headlamp Bracket Plug|Sportsters|
|71559-73|E1973, E1979|Plug|Handlebar \\ Starter Switch Hole Plug|XLH, XLCH|
|74521-77|1978-1981|Rubber Plug|Voltage Regulator \\ Wiring Harness Plug|XLH, XLCH|
|92073-81|1982-1983|Rubber Plug|Speedometer / Tach \\ Rear Housing Plug|XL, XLS|
|92077-62|L1962-1969|Plug|Magneto - Tach \\ Plug and O-ring|XLCH|{{ :techtalk:ih:elec:1962l-1969_xlch_tach_plug_92077-62_pic1_by_animalhouse2010.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, animalhouse2010, [[https://www.ebay.com/str/animalhouse2010?_trksid=p2047675.l2563|Link to Ebay store:]] ))|
===== Fittings =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}||||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|Pic(s)|
|9851|L1955- \\ \\ 1954-1979 \\ \\ 1954-1963 \\ 1954-1970|5/16"-32 Straight \\ Grease (Zerk) Fitting ((The Doctor71 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/156030-grease-fitting-size?t=1671259))|Shifter Shaft Grease Fitting \\ Brake Pedal \\ Kicker Grease Fitting \\ Rear Hub Grease Fitting \\ Front Hub Grease Fitting \\ Seat Bar Grease Fitting|KH, Sportsters|{{:techtalk:ref:oil:fitting_9851_grease_fitting_1954-1979_k_model_and_sportster.jpg?linkonly|Pic}}|
|24633-77|1977-1978|Piping Assembly|Crankcase Breather Valve|Sportsters|
|24912-52A|1954-1976|5/16" Tubing \\ with 24918-52 Fitting|Crankcase Vent Tube|KH, Sportsters|
|:::|Replaced by 24912-52B in 1977|||| |
|24912-52B|1977-1978|5/16" Tubing \\ with 24918-52A Fitting|Crankcase Vent Tube|Sportsters|{{ :techtalk:ref:oil:fitting_24912-52b_breather_tube_assembly_by_tomscybershop.jpg?linkonly |Pic1}} ((photos courtesy of TomsCyberShop.com www.TomsCyberShop.com))|
|24918-52|1952-1976|5/8"-11 x 5/16" \\ Flared Tube Nipple|Crankcase Breather Tube Fitting|KH, Sportsters| |
|:::|Replaced by 24918-52A in 1977||||:::|
|24918-52A|1977-1978|5/8"-11 x 5/16" \\ Flared Tube Nipple|Crankcase Breather Tube Fitting|Sportsters|{{ :techtalk:ref:oil:fitting_24918-52a_breather_pipe_fitting_by_57harleyrider.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] ))|
|25715-47|1954-1976|Grease (Zerk) Fitting \\ Press fit|Brake Cross Shaft Grease Fitting|KH, Sportsters|{{ :techtalk:ref:oil:fitting_25715-47_by_robisonmotorcycles.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|26272-81|1981-1985|Press Fit to 1/4" \\ Hose Bibb Steel Nipple|Trans Vent Fitting|Sportsters|
|26338-68|L1983-1984|1/8"-27 NPT 90° Fitting \\ (male & female ends)|Upper Head Oil Drain Fitting|XR-1000|{{ :techtalk:ref:oil:fitting_26338-68_by_hippysmack.jpg?linkonly |Pic1}} ((photo by Hippysmack)) \\ {{ :techtalk:ref:oil:fitting_26338-68_for_1986-1990_xl_application_by_hippysmack.jpg?linkonly |Pic2}} ((photo by Hippysmack))|
|:::|1986-1990|:::|Oil Pump Fitting \\ Return Outlet to Tank|Sportsters|:::|
|26383-32|1958-1969|Screw Kit|Chain Oiler Screw Kit|XLCH|{{ :techtalk:ref:oil:chain_oiler_adjuster_screw_26383-32_for_1958-1969_xlc_-_xlch_by_sum-body1.jpg?linkonly |Pic}} ((photo courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] ))|
|:::|Replaced by 63610-70 in 1971||||:::|
|26420-57|1957-1976|7/16"-24 NF x 1/8"-27 NPT \\ Nipple|Oil Pump Pressure Switch|Sportsters| |
|:::|Some say the pump side is 7-16"x24, one says M12x1. ((bustert of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/188994-lets-talk-oil-pumps/page2?t=2012025&page=2)) ((7-16" (.4375) x 24 TPI or converted to metric as; = 11.1125mm x 1.057mm (1/24 = 0.0416" or 1.05664mm). M12x1 = 12mm x 1mm so the 2 threads are close but they are not interchangeable. - Hippysmack)) \\ It's best to use a SAE and metric thread gauge on your particular fitting to be sure.||||:::|
|26496-75|1977-1981|1/8"-27 NPT to 3/8" \\ Hose Barb 90° Fitting|Oil Pump Return to \\ Oil Tank Fitting|Sportsters|{{ :techtalk:ref:oil:fitting_26496-75_by_hippysmack.jpg?linkonly |Pic1}} ((photo by Hippysmack))|
|:::|L1983-1985|:::|Oil Pump Fitting \\ Return to Oil Tank|Sportsters|:::|
|:::|L1983-1984|:::|Head Oil Drain Lower Fitting|XR-1000|:::|
|26569-58|1954-1976|(M-FM) Threaded Nipple Adapter|Oil Pump Pressure Switch|KH, XL, XLCH|{{:techtalk:ref:oil:fitting_26569-58_oil_pressure_switch_adapter_by_robisonmotorcycles.jpg?linkonly|Pic1}} ((photos courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|27371-76|1981-1982 \\ 1988-2006|Brass Sleeve to Plastic \\ 90° Hose Bibb|Carb Fuel Inlet|Sportsters|{{ :techtalk:ih:carb:1981-1982_and_1988-2002_sportster_carb_fuel_inlet_27371-76_by_hippysmack.jpg?linkonly |Pic1}} ((photo by Hippysmack))|
|27565-83|L1983-1984|NPT to Hose Bibb Nipple|Carb Nipple Fitting|XR-1000|
|27594-66|1966-1971|1/8"-27 x Angled \\ Hose Bibb Nipple|Carb Fuel Inlet Fitting|XLH, XLCH|{{ :techtalk:ih:carb:1966-1971_xlh-xlch_angled_carb_fuel_inlet_27594-66_by_jrsvintageharley1990.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, jrsvintageharley1990. [[https://www.ebay.com/str/jrsvintageharleyparts?_trksid=p2047675.l2563|Link to Ebay Store]] ))|
|27594-76|L1976-1980 \\ 1983-1987|Brass Sleeve to Plastic \\ 90° Hose Bibb|Carb Fuel Inlet|Sportsters|{{ :techtalk:ih:carb:1976l-1980_sportster_-_1983-1987_sportster_carb_fuel_inlet_fitting_27594-76_by_jrsvintageharley1990.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, jrsvintageharley1990. [[https://www.ebay.com/str/jrsvintageharleyparts?_trksid=p2047675.l2563|Link to Ebay Store]] ))|
|27738-69|L1983-1984|90° Fitting|Carb Fuel Inlet Fitting|XR-1000|
|33115-79|L1984-1985|Threaded Hex Stud (hollow) \\ 1-5/16" long, app .440" ID \\ (3/4" x 16 on both ends)|Oil Filter Adapter|XL, XLS, XLX|{{ :techtalk:ih:oil:79-85_oil_filter_adapter_1_by_hippysmack.jpg?linkonly |Pic1}} ((photo by Hippysmack)) \\ {{ :techtalk:ih:oil:79-85_oil_filter_adapter_2_by_hippysmack.jpg?linkonly |Pic2}} ((photo by Hippysmack))|
|34744-77|1977-1980|SAE 3/8" x 16 to 1/4" \\ Hose Bibb Nipple|Trans Vent Fitting|Sportsters| {{ :techtalk:ref:oil:fitting_34744-77_trans_vent_fitting_by_jfrost77hd_pic1.jpg?linkonly |Pic1}} ((photo courtesy of Frost Cycle Shack [[https://www.ebay.com/str/frostcycleshack|Link to Ebay Store]] )) \\ {{ :techtalk:ref:oil:fitting_34744-77_trans_vent_fitting_by_jfrost77hd_pic2.jpg?linkonly |Pic2}} ((photo courtesy of Frost Cycle Shack [[https://www.ebay.com/str/frostcycleshack|Link to Ebay Store]] ))|
|42318-72|1980-1985|Tee (w/ mounting ear)|Rear Brake Line Tee|Sportsters|
|43307-78|1978-1981|1/8"-27 NPT (M) \\ to (FM) AN3 (3/8"-24) \\ Inverted Flare 90° Elbow|(F) Master Cyl Brake Line Fitting|Sportsters|{{ :techtalk:ih:wheels:fitting_43307-78_for_brake_system_by_sum-body1.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] ))|
|:::|1978 \\ 1980-1981|:::|(F) Brake Line to Tee Fitting|Sportsters|:::|
|:::|1978-1979|:::|(R) Master Cyl Brake Line Fitting|Sportsters|:::|
|43308-78|1978-E1979|(FM) AN3 (3/8"-24) \\ Inverted Flare Tee ((ericfreeman of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/86228-gimme-a-break-er-some-brakes/page3?t=667563&page=3))|Front Brake Line Tee|Sportsters|{{ :techtalk:ih:wheels:fitting_43308-78_brake_line_tee_by_robisonmotorcycles.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|44141-77|1979-1981|Brass Fitting|Rear Caliper Brake Hose Fitting \\ Flare to Inverted Flare Insert|Sportsters|{{ :techtalk:ih:wheels:brake_caliper_hose_insert_44141-77_by_sum-body1.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] ))|
|44287-77|1979|Brass Tee (1M, 2FM)|Rear Brake Line Tee|Sportsters|{{ :techtalk:ih:wheels:1979_sportster_rear_brake_line_tee_44287-77_by_jrsvintageharley1990.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, jrsvintageharley1990. [[https://www.ebay.com/str/jrsvintageharleyparts?_trksid=p2047675.l2563|Link to Ebay Store]] ))|
|44310-77|L1979-1981|AN3 (3/8"-24) \\ Inverted Flare Tee|Front Brake Line Tee|Sportsters|
|44311-80|1982|Tee|Front Brake Line|XL, XLS|
|45518-73|E1973|(M) to (FM) \\ Inverted Flare Fitting|Front Brake Caliper \\ Line Fitting|Sportsters|
|50972-75|1975-1976|Grease Fitting|Right Footrest Support|Sportsters|{{ :techtalk:ref:oil:fitting_50972-75_by_robisonmotorcycles.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|:::|1993-2003|:::|Steering Head Grease Fitting|Sportsters|:::|
|62375-57|1957-E1958|1/8"-27 NPT \\ to 1/4" Hose Barb \\ 90° Fitting|Gas Line to Carb Fitting|Sportsters|{{ :techtalk:ref:oil:fitting_62375-57_by_57harleyrider.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] ))|
|:::|1970-2002|:::|Oil Tank Vent Fitting \\ at Rear of Cam Cover \\ Replaced by 62375-57A (2003)|Sportsters|:::|
|62375-62|1967-1969 ((corrected by the 1972 Parts Catalog Supplement 99451-72))|1/8"-27 NPT to 1/4" \\ Hose Barb 90° Fitting|Oil Tank Vent Fitting \\ Rear of Cam Cover|XLH|{{ :techtalk:ref:oil:fitting_62375-62_by_57harleyrider.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] ))|
|62484-81|1982-1985|Threaded Adapter|Rocker Box Oil Line \\ Upper Connector|Sportsters|
|62570-79|1979-1982|1/4"-18 NPT to 3/8" \\ Hose Bibb "Y" Fitting|Cam Cover Breather \\ Vent Fitting|Sportsters|{{:techtalk:ref:oil:fitting_62570-79_breather_valve_fitting_by_hudson_valley_motorcycle_parts.jpg?linkonly|Pic1}} ((photo courtesy of Northway Motorcycle Parts. [[https://www.ebay.com/str/northwayparts?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] ))|
|62570-83|1983-1990|1/4"-18 NPT to 3/8" \\ Hose Bibb Str Fitting|Cam Cover Breather \\ Vent Fitting|Sportsters|{{ :techtalk:ref:oil:fitting_62570-83_by_ct_kustoms.jpg?linkonly |Pic1}} ((photo courtesy of NitroFrankie Go-Fast HD, [[https://www.ebay.com/sch/m.html?item=194837126341&_ssn=ct_kustoms&_ipg=200&rt=nc|Ebay Items for Sale Page]] ))|
|62689-66|1966-1969|1/4"-18 NPT to 3/8" \\ Hose Bibb Nipple|Feed Hose Nipple|XLCH|{{techtalk:ref:oil:fitting_62689-66_feed_nipple_by_robisonmotorcycles.jpg?linkonly|Pic1}} ((photo courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|62696-62|L1962-1965|1/4"-18 NPT x 3/8" Hose \\ Bibb 90° Fitting|Oil Tank Feed Oil Fitting|XLCH|{{:techtalk:ref:oil:fitting_62696-62_oil_tank_feed_by_jfrost77hd_pic1.jpg?linkonly|Pic1}} ((photo courtesy of Frost Cycle Shack [[https://www.ebay.com/str/frostcycleshack|Link to Ebay Store]] )) \\ {{:techtalk:ref:oil:fitting_62696-62_oil_tank_feed_by_jfrost77hd_pic2.jpg?linkonly|Pic2}} ((photo courtesy of Frost Cycle Shack [[https://www.ebay.com/str/frostcycleshack|Link to Ebay Store]] ))|
|63525-50|1954-1966|Str NPT to 3/16" Steel \\ Tube Fitting|Oil Tank / Engine Fitting \\ Return Line (both ends)|KH, XL, XLH|
|63525-67|1970-1976|1/8"-27 NPT (M to FM) \\ 90° Elbow (hex body)|Oil Return Fitting \\ on Right Case|XLCH|{{ :techtalk:ref:oil:fitting_63525-67_oil_return_elbow_half_by_sum-body1_pic1.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] )) \\ {{ :techtalk:ref:oil:fitting_63525-67_oil_return_elbow_half_by_sum-body1_pic2.jpg?linkonly |Pic2}} ((photo courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] ))|
|63526-57|1957-1978 \\ 1958-E1962|1/8"-27 to Tube Fitting|Oil Tank Vent Line Fitting|XL, XLH \\ XLCH|
|:::|1957-1985|1/8"-27 x 3/16" O.D. ((brucstoudt of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/182061-stock-rocker-oil-line-inside-diameter?t=1961426))|Rocker Box Oil Line Connector|
|63527-57|1957-1978|Compression Nut|Rocker Box Oil \\ Line Fitting Nut|Sportsters|
|:::|Replaced by 63527-57A in 1979||||
|63527-57A|1979-1985|Compression Nut|Rocker Box Oil \\ Line Fitting Nut|Sportsters|{{ :techtalk:ref:oil:fitting_63527-57a_rocker_oil_line_nut_circa1982_by_57harleyrider_pic1.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] )) \\ {{ :techtalk:ref:oil:fitting_63527-57a_rocker_oil_line_nut_circa1982_by_57harleyrider_pic2.jpg?linkonly |Pic2}} ((photo courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] ))|
|63533-41|1958-1965|1/8"-27 NPT to 3/8" CAD \\ Str Hose Nipple Fitting|Oil Tank Return Nipple|XLCH|{{ :techtalk:ref:oil:fitting_63533-41_by_57harleyrider.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] ))|
|:::|1958-1965|:::|Oil Tank Feed Nipple|XLC, XLCH|:::|
|:::|1970-1976|:::|Oil Feed Nipple at Right Case|XLCH|:::|
|:::|1967-1976|:::|Oil Pump Feed Line|Sportsters|:::|
|:::|L1983-1984|:::|Head Oil Drain - Upper|XR-1000|:::|
|:::|L1983-1984|:::|Rocker Box \\ Oil Drain - Upper|XR-1000|:::|
|:::|1991-1999|:::|Oil Pump Feed \\ Inlet from Oil Tank|Sportsters|:::|
|63533-52|1954-E1961|NPT to Rubber Hose \\ Straight Fitting|Oil Tank Fitting \\ Feed Line to Engine|KH, XL, XLH|
|63539-54|L1954-E1961|NPT to Rubber Hose 45° Elbow|Engine Fitting \\ Feed Line Elbow|KH, XL, XLH|
|63539-66|1966-1969|1/8"-27 (M to FM) \\ 90° Elbow Fitting|Lower Feed Line Elbow|XLCH|{{:techtalk:ih:oil:1966-1969_xlch_lower_oil_feed_elbow_63539-66_by_rusty_dusty_motorcycle_parts.jpg?linkonly|Pic}} ((photo courtesy of Ebay seller, Rusty Dusty Motorcycle Parts. [[https://www.ebay.com/str/bialystreasures|Link to Ebay Store]] )) |
|63540-52|1958-E1962|1/8"-27 NPT x 3/8" \\ Hose Bibb 45° Elbow|Oil Return Line \\ Fitting at Case|XLCH|
|63540-53|1958-E1962 \\ 1958-1966 |1/4"-18 NPT x 3/8" \\ Hose Bibb 45° Elbow|Oil Pump Feed Line \\ Fitting at Case|XLCH \\ XLH|
|63540-62|L1962-1965|1/8"-27 NPT to 3/8" Hose Bibb \\ 45° Hex Body Fitting|Oil Return Outlet \\ on Right Case|XLCH|{{ :techtalk:ref:oil:fitting_63540-62_oil_pump_45_deg_elbow_hex_body_by_hippysmack.jpg?linkonly |Pic1}} ((photo by Hippysmack))|
|:::|1977-1981|:::|Oil Pump Fitting \\ Feed Inlet from Tank|Sportsters|:::|
|:::|1982-E1983|:::|Oil Pump Fitting \\ Feed and Return / Tank|Sportsters|:::|
|:::|Note: fitting redesigned in 1986 with smaller square body||||{{ :techtalk:ref:oil:fitting_63540-62_oil_pump_45_deg_elbow_by_sum-body1.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] ))|
|63540-66|1966-1969|(M) 1/8"-27 to (FM) 90° Elbow|Oil Return Line Elbow|XLCH|
|63542-52|1954-1955|Fitting|Vent Line Fitting|KH|
|63570-56|1954-1964|Metal Tube w/ Fittings|Vent Line Tubing|KH, XLH|
|63570-56A|1956-1966|Metal Tube w/ Fittings|Vent Line Tubing|XLH|
|63577-36|1958-1969|Banjo Fitting|Oil Tank Vent Line Fitting|XLCH|{{ :techtalk:ref:oil:1958-1969_xlch_oil_tank_vent_line_fitting_63577-36_and_banjo_bolt_63578-36_by_belmonthd.jpg?linkonly |Pic}} ((photo courtesy of belmonthd, [[https://www.ebay.com/str/belmonthd?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] ))|
|63578-36|1958-1969|Banjo Bolt|Oil Tank Vent Line \\ Fitting Bolt|XLCH|:::|
|63578-41|1958-1969|Banjo Fitting Assembly|Oil Tank Vent Line Fitting Bolt|XLCH|
|63578-52|1958-1965|1/8"-27 NPT x 1/4" \\ Hose Bibb Fitting|Oil Tank Vent Line \\ Fitting at Case|XLCH|{{ :techtalk:ref:oil:fitting_63578-52_by_ebay_57harleyrider_pic1.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] ))|
|:::|1967-1978|:::|Oil Tank Vent Fitting|XLH|:::|
|:::|1972-E1976|:::|Carb Fuel Inlet Fitting|Sportsters|:::|
|:::|L1983-1984|:::|Rocker Box \\ Oil Drain Lower Fitting|XR-1000|:::|
|63578-66|1958-1969|Banjo Fitting|Oil Tank Vent Line Fitting \\ (replaced 63578-52 in 1966)|XLCH|
|63579-83|L1983-1984|3/8" Hose Barb Tee|Rear Cylinder Head \\ Oil Drain Fitting|XR-1000|
|63590-69|1969-1971 \\ 1970-1971|Pipe w/ Fittings|Chain Oiler Pipe|XLH \\ XLCH|{{ :techtalk:ih:oil:1969-1971_xlh_1970-1971_xlch_chain_oiler_pipe_63590-69_by_animalhouse2010.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, animalhouse2010, [[https://www.ebay.com/str/animalhouse2010?_trksid=p2047675.l2563|Link to Ebay store:]] ))|
|63592-67|1967-1971 \\ 1970-1971|Pipe w/ Fitting and Hose|Chain Oiler Pipe|XLH \\ XLCH|{{ :techtalk:ih:oil:1967-1971_xlh-_1970-1971_xlch_rear_chain_oiler_pipe_63592-67_by_jrsvintageharley1990.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, jrsvintageharley1990. [[https://www.ebay.com/str/jrsvintageharleyparts?_trksid=p2047675.l2563|Link to Ebay Store]] ))|
|63592-72A|1972-1976|Pipe w/ Fitting and Hose|Chain Oiler Pipe|XLH/XLCH|{{ :techtalk:ih:oil:1972-1976_xlh-_xlch_chain_oiler_pipe_63592-72a_by_jrsvintageharley1990.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, jrsvintageharley1990. [[https://www.ebay.com/str/jrsvintageharleyparts?_trksid=p2047675.l2563|Link to Ebay Store]] ))|
|63595-67|1967-E1972 \\ 1970-E1972|Fitting w/ Mounting Tab|Rear Chain Oiler Body|XLH \\ XLCH|{{ :techtalk:ref:oil:fitting_63595-67_rear_chain_oiler_body_by_robisonmotorcycles.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|63595-72A|L1972-1976|Fitting w/ Mounting Tab|Rear Chain Oiler Body|XLH, XLCH|{{ :techtalk:ref:oil:fitting_63595-72_rear_chain_oiler_body_by_rusty_dusty_parts.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, Rusty Dusty Motorcycle Parts. [[https://www.ebay.com/str/bialystreasures|Link to Ebay Store]] ))|
|63601-54|1958-1969|2-Way (1-NPT) x (SAE) x 1/4" \\ Hose Bibb Regulating \\ Fitting (with screw)|Chain Oiler Hose \\ Oil Tank Fitting|XLCH|{{:techtalk:ref:oil:1958-1969_xlch_chain_oiler_fitting_63601-54_by_belmonthd.jpg?linkonly|Pic}} ((photos courtesy of belmonthd, compiled by Hippysmack [[https://www.ebay.com/str/belmonthd?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] ))|
|63604-72|1972-1976|Fitting|Rear Chain Oiler \\ Pipe Fitting|XLH, XLCH|{{:techtalk:ref:oil:fitting_63604-72_for_chain_oiler_pipe_by_57harleyrider.jpg?linkonly|Pic1}} ((photo courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] ))|
|63607-53|1954-1966|3-Way Threaded \\ Regulating Fitting|Chain Oiler Hose Fitting|KH, XL, XLH|
|63608-67|1967-1968|Fitting|Rear Chain Oiler Pipe Fitting|XLH|
|63609-69|1969-1971 \\ 1970-1971|Fitting|Rear Chain Oiler Pipe Fitting|XLH \\ XLCH|
|63609-72|1972-1978|1/8"-27 NPSF Fitting|Rear Chain Oiler Pipe Fitting|XLH, XLCH|{{ :techtalk:ref:oil:fitting_63609-72_by_57harleyrider.jpg?linkonly |Pic1}} ((photo courtesy of J&M's Ebay Store Harley Disney Toys, labeled by Hippysmack [[https://www.ebay.com/str/recycledharleydavidsonparts|Link to Ebay Store]] ))|
|:::|L1973-1977|:::|(F) Master Cyl Brake Line Fitting|Sportsters|:::|
|63610-53A|L1960-1970 \\ 1970|Screw|Chain Oiler Fitting Adj Screw|XL, XLH \\ XLCH|{{ :techtalk:ref:oil:1960l-1970_xl_-_xlh_1970_xlch_chain_adjuster_screw_63610-53a_by_jrsvintageharley1990.jpg?linkonly |Pic}} ((photo courtesy of Ebay seller, jrsvintageharley1990. [[https://www.ebay.com/str/jrsvintageharleyparts?_trksid=p2047675.l2563|Link to Ebay Store]] ))|
|:::|Replaced by screw kit 63610-70 in 1970||||:::|
|63610-70|1970-1976|Screw Kit|Chain Oiler Adjusting Screw|XLH, XLCH|{{ :techtalk:ref:tools:1954-1976_kh-sportster_chain_oiler_adj_screw_by_robison_motorcycles.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|:::|Replaced screw kits in 1970 for 1954-1969 KH, XL, XLH, XLCH chain oiler fittings||||:::|
|63614-72|1977-1978|Screw|Chain Oiler Adjusting Screw|XLH, XLCH|{{ :techtalk:ref:tools:1977-1978_xlh-xlch_chain_oiler_adjusting_screw_63614-72_by_sum-body1.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] ))|
|63792-77|1956-1978|3/8" Steel Sleeve|Oil Cooler Hose Connector|KH, Sportsters|
|74423-68|1968-1978|Tee|Oil Pressure Gauge Tee|Sportsters|
====== Engine ======
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}||||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|Pics|
|858|L1983-1984|Bolt|Rocker Arm Cover Bolt|XR-1000|
|908|1980|1/4" x 20 x 1-1/2" \\ Posidriv Head Screw|Primary Cover Screw|XL, XLS|
|911|1979-1980|1/4" x 20 x 1-3/4" \\ Posidriv Head Screw (black)|Cam Cover Screw|XLS|
|912|1979-1980|1/4" x 20 x 1-1/4" \\ Posidriv Head Screw (black)|Cam Cover Screw|XLS|
|913|1979-1980|1/4" x 20 x 1-1/2" \\ Posidriv Head Screw (black)|Primary Cover Screw|XLS|
|914|1979-1980|1/4" x 20 x 2-1/4" \\ Posidriv Head Screw|Primary Cover Screw|XLS|
|1175|L1953- |#10-24 x 1/4" \\ Fillister Head Screw (NC)|Clutch Cover Screw|K Models, Sportsters|
|1316W|1971-1973|1/4" x 20 x 1-3/4" \\ Phillips Head Screw (NC)|Cam Cover Screw|XL, XLCH|
|:::|1974-1980|1/4" x 20 x 1-3/4" \\ Posidriv Head Screw|Cam Cover Screw|XL, XLCH|
|1317W|1971-1973|1/4" x 20 x 1-1/4" \\ Phillips Head Screw (NC)|Cam Cover Screw|XL, XLCH|
|:::|1974-1980|1/4" x 20 x 1-1/4" \\ Posidriv Head Screw|Cam Cover Screw|XL, XLCH|
|1369|1958-1969|1/4" x 20 11/16" \\ Fillister Head Screw (NC)|Primary Cover Screws|XLCH|
|1370W|1971-1973|1/4" x 20 x 2-1/4" \\ Phillips Head Screw (NC)|Cam Cover Screw|XL, XLCH|
|:::|1974-1980|1/4" x 20 x 2-1/4" \\ Posidriv Head Bolt|Cam Cover Screw|XL, XLCH|
|:::|1980|:::|:::|XLS|
|1381|1977-1980|1/4" x 20 x 2-1/2" \\ Posidriv Head Screw|Cam Cover Screw|XL, XLCH|
|1435W|1971-1973|1/4" x 20 x 3/8" \\ Phillips Head Screw|Primary Oil Level Plug Bolt|XLH, XLCH|
|2268|1958-1965|#12-24 x 1/2" \\ Fillister Head Screw (NC)|Primary Chain \\ Inspection Cover Screw|XLCH|
|2268W|1958-1969|#12-24 x 1/2" Countersunk \\ Head Screw (NC)|Primary Chain \\ Inspection Cover Screw \\ Replaced Screw #2268 on 1966|XLCH|
|2269W|1964-1969|#12-24 x 1/2" Countersunk \\ Head Screw (chrome)|Primary Chain \\ Inspection Cover Screw|XLCH|
|2329|1952-1956|1/4" x 24 x 13/16" Oval \\ Head Screw (NS)|Tappet Guide Bolt|K Models|
|2345|1952-1970 \\ 1970|1/4" x 20 x 1-1/2" Oval \\ Slotted Head Bolt (NC)|Primary / Cam Cover Bolt|K Models, XL, XLH \\ XLCH|
|2346W|1971-1976|1/4" x 20 x 1-1/2" Posidriv \\ Fillister Head Screw|Primary Chain \\ Inspection Cover Screw|XLH, XLCH|
|:::|1979- |:::|Top Right Primary Cover Screw|XL, XLCH|
|2350W|1967-1970 \\ 1970|1/4" x 20 x 1-3/4" \\ Countersunk Head Screw|Primary Cover Screw|XLH \\ XLCH|
|2351W|1971-1976|1/4" x 20 x 2" \\ Phillips Head Screw|Primary (tin) \\ Cover Screw|XLH, XLCH|
|2352|1953-1970|1/4" x 20 x 2-1/4" Oval \\ Slotted Head Screw (NC)|Cam Cover Screw|K Models, Sportsters|
|2353|1953-1970|1/4" x 20 x 2-5/16" Oval \\ Slotted Head Screw (NC)|Cam Cover Screw|K Models, Sportsters|
|2420|1971-1985|1/4" x 20 x 3/4" \\ Pozidriv Truss Head Screw|Primary Oil Level Plug Screw|Sportsters|
|2421W|1967-1970 \\ 1970|#10-24 x 1-3/4" \\ Countersunk Head Screw|Primary Cover Screw|XLH \\ XLCH|
|2422W|1971-1976|#10-24 x 1-7/8" \\ Pozidriv Fillister Head Screw|Primary Cover Screw|XLH, XLCH|
|2587|1977-1978 \\ L1980-1990|:::|Primary Chain Adj Pad Bolt|Sportsters|
|2600|L1983- |#10-24 x 3/8" \\ Pozidriv Pan Head (locking)|Crankpin Lockwasher Screw|XL, XLS|
|2622|1972-1978|#8-32 x 7/16" \\ Pozidriv Head Screw|Timer Cover Outer Screw|XLH, XLCH|
|2628|1971|#8-32 x 7/16" \\ Countersunk Head Screw|Timer Cover Outer Screw|XLH, XLCH|
|2660|1964-1969|#12-24 x 1/2" Chrome \\ Countersunk Head Screw|Primary Cover Screw|XLCH|
|2669 \\ \\ 2669W ('64) \\ \\ 2660 ('76)|1953-1979|#10-24 x 3/8" \\ Round Head Screw (NC) \\ #10-24 x 3/8" \\ Round Head Screw (NC) \\ #10-24 x 3/8" \\ Pozidriv Pan Head Screw|Crankpin / Flywheel Shaft \\ Lock Plate Screw \\ |K Models, Sportsters|
|2669W|1958-1969|#10-24 x 3/8" \\ Round Head Screw (NC) |Primary Cover Screw|XLCH|
|2851|1954-1969|3/8" x 16 x 7/8" \\ Hex Head Bolt|Upper Primary Adjuster \\ to Brace Bolt|XLCH|
|2851|L1983-1984| |Manifold Mounting Bolt|XR-1000|
|2871W|1982-1985|5/16" x 18 x 1-1/4" \\ Hex Head Bolt|Upper Front Engine Mount to \\ Frame Bracket Bolt|XL, XLS, XLX|
|:::|1967-|:::|Left Crankcase Bolt \\ (replaced 4022W in 1976)|XLH|
|2879W|1954-1976|3/8" x 16 x 1" Hex Head Bolt|Rear Motor Mount \\ to Engine Top Bolt|KH, XL, XLH, XLCH|
|2879W|1979-1985|3/8" x 16 x 1" Hex Head Bolt|Rear Motor Mount \\ to Engine Top Right Bolt|XL, XLS|
|3206B|L1983-1984|#8-32 x 3/16" \\ Socket Head Set Screw|Rocker Arm Shaft Set Screw|XR1000|
|3250|1977-1990|5/16" x 18 x 2" \\ Socket Head Set Screw|Primary Chain Adjuster Screw|Sportsters|
|3412|1979-1985|Stud 5/16" x 24 x 2-1/4" one end, \\ 5/16" x 18 x 1/2" other end \\ (zinc)|Rocker Arm Cover to \\ Frame Bracket Bolt|XL, XLCH, XLS|
|3413|1984-1985|5/16" x 18 x 5/8" \\ Hex Socket Head Screw| |XL, XLS, XLX|
|3417|1979-1980|5/16" x 24 x 2-1/4" one end, \\ 5/16" x 18 x 1/2" other end \\ (black)|Rocker Arm Cover to \\ Frame Bracket Bolt|XLS|
|3440|1979-1980|3/8" x 16 x 1/2 " \\ Hex Head Bolt|Rear Motor Mount to \\ Engine Top Right Bolt|XL, XLCH, XLS|
|3455|1982-1985|3/8" x 24 x 3-3/4" \\ Hex Head Bolt|Rear Motor Mount \\ to Frame Bolt|XL, XLS, XLX|
|3467|1979-1985|5/16" x 24 x 1-1/4" Hex Head \\ Bolt (grade 5)|Rocker Box Bolt \\ (short center bolt)|XLS|
|3468|1979-1985|5/16" x 24 x 2-1/4" Hex Head \\ Bolt (grade 5, black)|Rockerbox Bolt|XLS|
|3470|E1979|7/16" x 20 x 7/8" \\ Hex Head Bolt|Motor Mount to Head Bolt|XLS|
|3474|L1979-1985|7/16" x 20 x 1" \\ Hex Head (NF)|Upper (center) Motor \\ Mount to Heads|XLS|
|3478|1981-1985|1/4" x 20 x 2-1/2" \\ Socket Fillister Head Bolt|Primary Cover Bolt|XL, XLS, XLX|
|3479|1981-1985|1/4" x 20 x 2-1/4" \\ Socket Head Bolt|Primary Cover Bolt|XL, XLS, XLX|
|:::|1981-1985|:::|Cam Cover Bolt|XL, XLS, XLX|
|3480|1981-1985|1/4" x 20 x 1-3/4" \\ Socket Head Bolt|Cam Cover Bolt|XL, XLS, XLX|
|3481|1981-1985|1/4" x 20 x 1-1/2" \\ Socket Head Bolt|Primary Cover Bolt|XL, XLS, XLX|
|3482|1981-1985|1/4" x 20 x 1-1/4" \\ Socket Head Bolt|Cam Cover Bolt|XL, XLS, XLX|
|3720|1952-1976 \\ 1958-1969|1/4" x 28 x 7/16" \\ Hex Head Bolt (NF)|Primary Tin Cover \\ Oil Level/Drain|K Models, XL, XLH \\ XLCH|
|3728|1954-1970|1/4" x 20 x 1/2" \\ Hex Head Bolt (NC)|Primary Oil Level Plug|KH, XL, XLH, XLCH|
|3768|1979-1985|1/4" x 20 x 2-1/2" \\ Hex Head Bolt|Lower Front Case Bolt|Sportsters|
|3943W|L1971-1976|5/16" x 24 x 3/8" \\ Hex Head Bolt (NF)|Lower Primary Chain Adj \\ to Brace Bolt|XL, XLCH|
|3945|1973-1979|3/8" x 24 x 2-1/4" \\ Hex Head Bolt|Left Rear Motor Mount \\ to Frame Bolt|XL, XLH, XLCH, XLS|
|3952|1961-1969|5/16" x 18 x 7/16" \\ Hex Head Bolt (NC)|Coil to Case (top) Mounting Bolt|XLCH|
|3953W|1954-E1971 \\ 1970-E1971|5/16" x 24 x 1/2" ex Head Bolt \\ (NF, Grade 5, Cadmium)|Lower Primary Chain Adj \\ to Brace Bolt|KH, XL, XLH \\ XLCH|
|3953W|1954-1981|5/16" x 24 x 1/2" \\ Hex Head Bolt \\ (NF, Grade 5, Cadmium)|Oil Cooler to \\ Mounting Bracket Bolt \\ oil cooler kit \\ (62571-77 or 62577-77)|XL, XLCH, XLS|
|3987|1979-1981|5/16" x 18 x 3/4" \\ Hex Head Bolt|Deluxe Oil Cooler to \\ Mounting Bracket Bolt|XL, XLCH, XLS|
|3991|1977-1985|5/16" x 18 x 7/8" \\ Hex Head Bolt|Upper Front Engine \\ Mount "L" Bracket Bolt|XL, XLCH, XLS|
|3996|1956-1981|5/16" x 24 x 7/8" \\ Hex Head Bolt|Oil Cooler Bracket \\ to Frame Bolt \\ oil cooler kit \\ (62571-77, 62577-77)|XL, XLCH, XLS|
|4005W|1957-1975|5/16" x 18 x 1" \\ Hex Head Bolt (NC)|Tappet Guide Bolt \\ (replaced by 4017 in '76)|Sportsters|
|4012|1957-1978|5/16" x 24 x 1-1/8" \\ Hex Head Bolt (NF)|Rocker Box Bolt \\ (short center bolt) \\ (Replaced by 4014W in -78A)|XL, XLH, XLCH|
|4014W|1957-1985|5/16" x 24 x 1-1/4" \\ Hex Head Bolt (NF)|Rocker Box Bolt \\ (short center bolt) \\ (Replaced 4012 in -78A)|XL, XLH, XLCH, XLS|
|4017|1957-1985 \\ L1983-1984|5/16" x 18 x 1" \\ Hex Head Bolt (NC)|Tappet Guide Bolt \\ (replaced 4005W in '76)|Sportsters \\ XR-1000|
|4022W|1967-1975|5/16" x 18 x 1-1/8" \\ Hex Head Bolt|Left Crankcase Bolt \\ (replaced by 2871W in '76)|XLH|
|4060W|1957-1972|5/16" x 24 x 2-1/4" \\ Hex Head Bolt (NF)|Rocker Box Bolts \\ (Replaced by #4710 in 1973)|Sportster|
|4066|1953-1976|5/16" x 18 x 2-13/32" \\ Hex Head Bolt (NC)|Case Bolt|K Models, Sportsters|
|4067|1954-1985|5/16" x 18 x 4-1/2"|Right Case Bolt \\ Oil Hose Clamp Screw|KH, XL, XLCH, \\ XLS, XLX|
|4068|1977-1981|5/16" x 18 x 2-1/2" Hex Hd Bolt \\ (grade 5, zinc)|Upper Rear Engine \\ Mount to Frame \\ Bracket Bolt|XL, XLCH XLS|
|4086|1957-1985|5/16" x 18 x 3" Hex Hd Bolt|Case Bolt \\ (and inside primary)|Sportsters|
|:::|L1983-1984|:::|Rocker Arm Cover Screw|XR1000|
|4100 \\ 4100HW|1952-1976|5/16" x 18" x 4-1/16" \\ Hex Head Bolt (NC)|Crankcase Mounting Bolt|K Models, Sportsters|
|4106|1952- |5/16" x 18" x 4-7/16" \\ Hex Head Bolt (NC)|Gearcase Bolt|K Models, Sportsters|
|4251|L1975-1976|5/16" x 24 x 4-1/2" \\ Hex Head Bolt|Crankcase Bolt|XLH/XLCH|
|4300|1952- |3/8" x 16 x 7/8" \\ Hex Head Bolt (NC)|Primary Chain \\ Adjuster Screw|K Models, Sportsters|
|4319|1982|3/8" x 24 x 1" Hex Head \\ Bolt (grade 5, zinc)|Motor Support to \\ Frame Bracket Bolt|XL, XLS|
|:::|L1984-1985|:::|Lower Front Motor Mount \\ (both front bolts)|XL, XLS, XLX|
|4335W \\ 4336W|1952-1971|3/8" x 24 x 1-1/8" \\ Hex Head Bolt (NF)|Motor Mount Bolt \\ Head Straddle \\ to Cross Brace|K Models, Sportsters|
|4336W|1967-1981|3/8" x 24 x 1-1/8" \\ Hex Hd Bolt (NF)|Rear Motor Mount \\ to Upper Frame Bolt|XL, XLCH, XLS|
|:::|(replaced by 4335W in '68)||||
|4337W|1983-1985|3/8" x 24 x 1-1/4" Hex Head \\ Bolt (grade 5, zinc, NF)|Motor Support to \\ Frame Bracket Bolt|XL, XLS. XLX|
|4340|1979-1985|5/16" X 18 X 4-1/4" \\ Socket Head Bolt|Right Case Bolt|Sportsters|
|4348|1953- |3/8" x 16 x 1-3/16" \\ Hex Head Bolt (NC)|Rear Motor Mount to \\ Motor Bolt|K Models, Sportsters|
|4354|E1967- |3/8" x 16 x 1-3/8" \\ Hex Head Bolt|Chain Adj Mounting Bolt|XLH|
|4380W|1954-E1962|3/8" x 24 x 2" \\ Hex Head Bolt|Rear Motor Mount to \\ Frame (lower) Bolt \\ (replaced 4388B in '76)|KH, XL, XLH, XLCH|
|4388B|1954-E1962|3/8" x 24 x 2-1/16" \\ Hex Head Bolt|Rear Motor Mount to \\ Frame (lower) Bolt \\ (replaced by 4388W in '76)|KH, XL, XLH, XLCH|
|4392|L1983-1984|5/16" x 18 x 3-1/4" \\ Hex Hd Bolt (grade 5)|Rocker Arm Cover Screw|XR1000|
|4412|L1962-1976|3/8" x 24 x 2-1/2" \\ Hex Head Bolt|Rear Engine Mounting Bolt \\ (lower bolts)|XLH/XLCH|
|4413|1973-1985|3/8" x 24 x 5-1/2" \\ Hex Head Bolt|Lower Front Motor Mount \\ (lower rear bolt)|Sportsters|
|4415|1979-1981|3/8" x 24 x 3" \\ Hex Head Bolt|Rear Motor Mount \\ to Frame Bolt|XL, XLCH, XLS|
|4420|L1982-1985|3/8" x 16 x 2-3/4" \\ Hex Head Bolt \\ (grade 5, zinc)|Rear Motor Mount to \\ Frame (lower) Bolt|XL, XLS, XLX|
|4434W|L1983-1985|3/8" x 24 x 3-1/4" \\ Hex Head Bolt \\ (grade 5, zinc)|(R) Motor Mount to \\ Frame (upper) Bolt|XL, XLS, XLX|
|:::|L1983-1984|:::|Upper Rear Motor Mount Bolt|XR-1000|
|4435W|L1983-1985|3/8" x 24 x 3-1/2" \\ Hex Head Bolt \\ (grade 5, zinc)|(R) Motor Mount to \\ Frame (lower) Bolt|XL, XLS, XLX|
|:::|L1983-1984|:::|Lower Rear Motor Mount Bolt|XR-1000|
|4452B|L1962- |3/8" x 24 x 2-1/2" \\ Hex Head Bolt (NF)|Rear Motor Mount \\ Bolt (frame)|Sportsters|
|4452HB|L1962-1975|3/8" x 24 x 2-1/2" \\ Hex Head Bolt|Rear Motor Mount \\ to (lower) Frame Bolt \\ (replaced by 4412 in '75)|XLH/XLCH|
|4618W \\ 3470|1957-1979|7/16 x 20 x 7/8" Hex Head|Upper (center) \\ Motor Mount to Heads|XLH, XLCH|
|:::|E1979|:::|:::|XLS|
|4624|1952-1956|7/16" x 20 x 1-3/32" \\ Hex Head Bolt|Motor Support Bracket|K, KH|
|4640|1979-1985|7/16" x 20 x 1" \\ Hex Head Bolt|Motor Mount to Head Bolt|XL, XLCH|
|4666|1952-1956|7/16" x 14 x 1-11/16" \\ Hex Head Bolt|Head Bolt|K, KH|
|4709|L1973-1985|7/16" x 20 x 2-21/32" \\ Hex Head Bolt|(12 pt) Head to Cylinder Bolt|Sportsters|
|4710|1957-1985|5/16" x 24 x 2-1/4" Hex Head \\ Bolt (grade 5, zinc)|Rocker Arm Cover Bolt \\ (replaced 4060W in '73)|XL, XLCH, XLS, XLX|
|4712|E1977-1978|3/8" x 16 x 3-1/4" \\ Hex Head Bolt|Upper Primary Adjuster \\ to Brace Bolt|XL, XLCH|
|4714W|1957-E1973|7/16" x 20 x 2-21/32" \\ Hex Head Bolt|Head to Cylinder Bolt|Sportsters|
|4715 \\ 4715W|1954-1956|7/16" x 14 x 3" Hex Head \\ Bolt|Head/Motor Mount \\ Bracket Bolt|KH|
|4716W|1979-1985|3/8" x 16 x 1-1/4" Hex Head \\ Bolt (grade 5, zinc)|Rear Motor Mount to \\ Case (top) Bolt|Sportsters|
|4716W|1954-1976 \\ 1970-1976|3/8" x 16 x 1-1/4" Hex Head \\ Bolt (grade 5, zinc)|Upper Primary Adjuster \\ to Brace Bolt|KH, XL, XLH \\ XLCH|
|4718|1953|7/16" x 14 x 3-5/16" \\ Hex Head Bolt|Head/Motor Mount \\ Bracket Bolt|K|
|4725|1975|5/16" x 24 x 2-3/4" \\ Hex Head Bolt|Rocker Box Mounting Bolt|XL, XLCH|
|4726|L1972-1976|7/16" x 20 x 1-1/2" \\ Hex Head Bolt|Motor Bracket Bolt|XLH/XLCH|
|11724|L1983-1984|9-3/32" Long Stud|Cylinder Head Stud|XR-1000|
|11725|L1983-1984|Stud|Front Rocker Arm Cover Stud|XR-1000|
|16235-52|1952-- |3/8" x 24 x 5-3/16" (NF)|Lower Front Motor Mount \\ (upper rear bolt)|K Models, Sportsters|
|:::|Part number changed to (16235-52A) in the -78B catalog (issued in 1989). \\ Length is 5-3/16" in the -57, -59, -63, 78A parts catalogs. \\ Length in the -78B parts catalog is 5-1/4".||||
|:::|1979-1985|3/8" x 24 x 5-1/4" (NF)|Lower Front Motor Mount \\ (upper rear bolt)|XL, XLCH, XLS, XLX|
|16235-52|1954-1976|3/8" x 24 x 5-3/16" (NF)|Lower Front Motor Mount \\ (upper rear bolt)|K Model, Sportster|
|16235-52|1979-1985|3/8" x 24 x 5-1/4" \\ Hex Head Bolt|Lower Front Motor Mount \\ (upper rear bolt)|XL, XLCH, XLS|
|16235-52A|1989- |3/8" x 24 x 5-1/4" (NF)|Lower Front Motor Mount \\ (upper rear bolt)|Sportsters|
|16236-52|1952-1972|3/8" x 24 x 5-7/16" (NF)|Lower Front Motor Mount \\ (lower rear bolt)|K Models, Sportster|
|16237-52|1952-1956|3/8" x 24 x 7-1/8" (NF)|Lower Front Motor Mount \\ (both front bolts)|K Models|
|16237-57|1957-E1984|3/8" x 24 x 6-13/16" (NF)|Lower Front Motor Mount \\ (both front bolts)|Sportster|
|16830-54|1954-1971|3/8" x 2-5/16" stud (NC & NF)|Cylinder Base Stud|KH, Sportster|
|16830-72|1972-1985|3/8" x 2-11/32" Stud (NF x NC)|Cylinder Base Stud|Sportster|
|16865-52|1957-1978|7/16" x 20 x 7/8" Hex Head Bolt \\ (w/ cotter pin hole)|Upper Motor Mount \\ Bracket to Frame|Sportster|
|17448-57|1957-E1971|5/16" x 24 \\ Slotted Head Screw|Rocker Shaft End Screw|Sportster|
|17448-71|L1971-E1978|1/2" x 20 \\ Allen Head Screw|Rocker Shaft End Screw|Sportster|
|17448-71A|L1978-1985|1/2" x 20 \\ Allen Head Screw (chrome)|Rocker Shaft End Screw|Sportster|
|18554-57|1957-1985|Screw and Nut|Tappet Screw and Nut Kit|Sportster|
|18566-57|1957-1985|Screw|Tappet Screw|Sportster|
|24608-54|1957-1976|Screw|Gear Shaft Bushing Screw|Sportster|{{ :techtalk:ih:engmech:1957-1976_sportster_pinion_shaft_bearing_bushing_screw_24608-54_by_ebay_sum-body1_pic2.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, Sum-body's Harley Parts, [[https://www.ebay.com/str/sumbodysharleyparts|Link to Ebay Store]] ))|
|24810-57|1957-E1975|5/16" x 24 x 5" \\ (NF, both ends)|Crankcase Stud|Sportster|
|24812-57|1963- |Stud with Nut|Crankcase Stud|XLH, XLCH|
|24817-52|1952-E1982|3/8" x 3-1/4" \\ (course threads and fine threads)|Rear Motor Mounting Studs|K Model, Sportster|
|24818-52|1953-1960|5/16" x 1-11/16" \\ (course threads and fine threads)|Toolbox Mount Stud \\ (top of primary)|K Models, Sportster|
|:::|1961-1966|:::|:::|XLH|
|24824-67|L1972-E1975|3/8" x 2" Stud \\ (NC one end, NF other end)|Rear Motor Mounting \\ Stud (right)|Sportster|
|24825-66|L1970-E1972|3/8" x 1-5/8" Stud \\ (NC one end, NF other end)|Rear Motor Mounting \\ Stud (right)|Sportster|
|24825-82|L1982-1985|3/8"-16 x 3-1/8" \\ (NC - both ends)|Rear Motor Mounting Stud|Sportster|
|24827-66 \\ 24827-66A|1983-1985|5/16" x 1-7/8" Hex Stud \\ (NC one end, NF the other)|Front Intake (only) \\ Tappet Block Stud|XL, XLS|
|25111-53|1953-E1955|Screw|Siphon Tube Screw|K, KH|
|25787-54 |1954-1956|Stud|Idler Gear Stud|KH|
|25787-57 |1957-E1984|Stud|Idler Gear Shaft|Sportster|
|32601-78|L1972-1978|Stud|Timer Cover Inner Stud \\ (replaced 32608-72)|XLH, XLCH|
|32608-70|1971-E1972|Stud|Timer Cover Inner Stud|XLH, XLCH|{{ :techtalk:ref:tools:1971-e1972_sportster_ignition_breaker_plate_timer_stud_32608-70_by_robison_motorcycles.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|32608-72|L1972-1976|Stud|Timer Cover Inner Stud \\ (replaced by 32601-78)|XLH, XLCH|
|33088-64|L1975- |3/8" x 16 x 7/16" Hex Head Bolt|Rear Motor Mount to \\ Engine Top Right Bolt|XL, XLCH|
|34957-52|1953-1956|Screw|Primary Cover Screw|K, KH|
|34957-57|1957-1966|Round Head Screw|Primary Cover Screw|XL, XLH|
|40018-77|1977-1985|Stud|Primary Adj Pivot Stud \\ Front Chain Adj \\ Kit (39967-77A)|XL, XLCH, XLS|
====== Oil Pump ======
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}||||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|Pic|
|1794|1979-1981|1/4" x 20 x 2/12" Socket \\ Fillister Head Bolt|Oil Pump Mounting Bolt|XL, XLCH, XLS|
|2881W|L1971-1976|1/4" x 20 x 2" \\ Hex Head Bolt|Oil Pump Mounting Bolt|XLH/XLCH|
|3478|1977-1985|1/4" x 20 x 2-1/2" Socket \\ Fillister Head Bolt|Oil Pump Mounting Bolt|Sportsters|
|24819-52|1952-E1971|1/4" x 2-5/16" \\ (course one end, fine the other)|Oil Pump Mounting Stud|K Models, Sportster|{{ :techtalk:ref:tools:1952-e1971_k_models_-_sportster_oil_pump_mounting_stud_by_animalhouse2010.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, animalhouse2010, [[https://www.ebay.com/str/animalhouse2010?_trksid=p2047675.l2563|Link to Ebay store:]] ))|
|26389-55|1955|Set Screw|Check Valve Set Screw|KH|
====== Carburetor, Intake Manifold and Air Cleaner ======
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}||||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|Pic(s)|
|930|1972-1978 \\ 1979-1985|#10-24 x 1-1/4" Pozidriv \\ Fillister Head Screw|Intake Manifold to \\ Engine Clamp Screw|XLH, XLCH, \\ XLS|
|930|1972-E1974|#10-24 x 1-1/4" Pozidriv \\ Fillister Head Screw|Intake Manifold Clamp Screw|XLH, XLCH|
|:::|L1976-1980|:::|:::|XL, XLCH, XLS|
|931|1979- |#10-24 x 1-1/2" Pozidriv \\ Fillister Head Screw|Intake Manifold to \\ Engine Clamp Screw|XL, XLCH|
|990W|1966-1971|#6-32 x 1/4" Fillister Head Screw|Choke Lever Wire Block Screw|XLH, XLCH|
|991|1966-1971|#10-24 x 1" Pozidriv \\ Fillister Head Screw|Intake Manifold to Engine Screw|XLH, XLCH|
|993|1952-1956|#6-32 x 1/4" Fillister Head Screw|Linkert Throttle|K Models|
|:::|1957-* |:::|Carb Air Disc|Sportster|
|993W|1966-1971|#6-32 x 1/4" Fillister Head Screw|Tillotson Throttle Wire Screw|XLH, XLCH|
|:::|1954-1964|:::|Linkert Throttle/Air/Choke \\ Disc Screw|KH, Sportsters|
|:::|1966-? |#6-32 x 5/16" Fillister Head Screw|Throttle Lever Wire \\ Block Screw|XLH, XLCH|
|1058W|1961-1965|#8-32 x 5/16" Fillister Head Screw|Linkert Carb Control Wire Block|XLH, XLCH|
|1063|1952-1956|#8-32 x 3/8" Fillister Head Screw \\ (NC, White)|Throttle/Choke Lever Block Screw \\ Timer Control Wire Lock Screw|K Models|
|1063|1957-1960|#8-32 x 3/8" Fillister Head Screw \\ (NC, White)|Linkert Control Wire Block|Sportsters|
|1063W|1954-1960|#8-32 x 3/8" Fillister Head Screw|Linkert Control Wire Block|KH, Sportsters|
|1073W|1961-1965|#8-32 x 3/4" Fillister Head Screw|Linkert Throttle Lever Screw|XLH, XLCH|
|1074W|1957-1960|#8-32 x 7/8" Fillister Head Screw|Linkert Throttle Lever Screw|Sportster|
|11722|1983- |1-3/4" Long Stud|Upper Carb to Intake Stud|XL, XLS|
|11723|1983- |1-1/4" Long Stud|Lower Carb to Intake Stud|XL, XLS|
|1183|1952-1956|#10-32 x 5/16" Fillister Head Screw|Low Speed Needle Valve \\ Lock Screw|K Models|
|1207W|1957-1965|#10-24 x 5/8" Fillister Head Screw|Linkert Carb Bowl Screw|Sportsters|
|1214 \\ 1214HW|1957-1978|#10-24 x 3/4" Fillister Head Screw|Intake Manifold Clamp Screw|Sportsters|
|1300 \\ 1300B|1957-1965|#12-24 x 1/2" Fillister Head Screw|Linkert Air Cleaner Backing \\ Plate to Carb Screw|XL, XLH, XLCH|
|2402C \\ 2402W|1956-1978|5/16" x 24 x 23/32" Oval Hd Screw \\ 5/16" x 24 x 23/32" Oval Hd Screw|A/C Cover Screw|KH, Sportsters|
|:::|Discrepancy in parts books as to oval and fillister head.||||
|2402W|1983-1985|5/16" x 24 x 11/16" Phillips Oval \\ Countersunk Hd Screw (chrome)|Air Cleaner Cover Screw|XL, XLS|
|2540|1966-1971|#4-36 x 1/4" Fillister Head Screw|Tillotson Accel Pump Lever Screw|XLH, XLCH|
|2574W|1957-1965|#6-32 x 1/4" Round Head Screw|Linkert Throttle Disc Screw \\ and Nozzle Vent Clamp Screw|Sportsters|
|2578B|1957-1965|#6-32 x 5/16" Round Head Screw|Linkert Float Lever Bracket Screw|Sportster|
|2589|1954-1965|#6-32 x 1/4" Pozidriv \\ Pan Head Screw|Choke Disc Screw|KH, Sportsters|
|:::|1966-1971|:::|Choke Lever Wire Block Screw|XLH, XLCH|
|2632|1954-1956|#8-32 x 7/16" Round Head Screw|Throttle Arm Screw|KH|
|2758|1966-1978|:::|Carb to Air Cleaner \\ Backing Plate Screw|XLH, XLCH|
|2774|E1979|1/4" x 20 x 5/8" Pozidriv Screw|Air Cleaner Backing Plate \\ to Carb Screw|XL, XLCH, XLS|
|2632|1952- |#8-32 x 7/6" Round Head Screw|Carb Throttle Lever Arm|XL, XLH|
|3413|1979-1981 \\ L1982|5/16" x 18 x 5/8" Socket Head Screw|Air Cleaner Cover Screw|XL, XLCH, XLS|
|3458|1979-E1982|5/16" x 18 x 1" Socket Head Screw|Air Cleaner Cover Screw \\ (w/ air intake grill)|XL, XLCH, XLS|
|3566W|1957|#10-1/2" Self Tapping Screw|Choke Lever Bracket|XL|
|3625|1952-1956|#12-24 x 3/8" Hexagon Head Screw|A/C Backing Plate \\ to Carb Screw|K Models|
|3738|1972-E1976|1/4" x 28 x 1/2" Hex Head Bolt|Throttle Cable Clamp Bolt|XLH, XLCH|
|:::|1981-1983|:::|Throttle Cable Clamp Bolt \\ (from throttle clamp kit 27449-72)|XL, XLS|
|3765|1966-1971|1/4" x 28 x 5/8" Hex Head Bolt|Air Cleaner to Bracket Bolt|XLH, XLCH|
|3767B|1972-1978|1/4" x 20 x 9/16" Hex Head Bolt|Air Cleaner to \\ Bracket Bolt|XLH, XLCH|
|3767B|L1979-1984|1/4" x 20 x 5/8" Hex Head Bolt|Air Cleaner Backing Plate \\ to Carb Screw|XL, XLCH, XLS|
|3787|1985- |Bolt|Air Cleaner Backing Plate \\ to Carb Screw|XL, XLS, XLX|
|3825|1956|1/4" x 28 x 1" Hex Head Bolt (NF)|A/C Backing \\ Plate Bracket|KH|
|3987|1979-1982|5/16" x 18 x 3/4" Hex Head Bolt|Air Cleaner to \\ Head Bracket Bolt|XL, XLCH, XLS|
|3991|1983-1985|5/16" x 24 x 1-1/4" Pozidriv \\ Pan Head Screw|Lower Intake to \\ Carb Screw|XL, XLS, XLX|
|4323|1957-1965|3/8" x 16 x 1" Hex Head Bolt (NC)|Linkert \\ Choke Cable Bracket Bolt|Sportsters|
|4323|1966--|3/8" x 16 x 1" Hex Head Bolt (NC)|Tillotson \\ Throttle Cable Clamp Bolt|XL|
|20014-67|E1972|5-16" x 18 x 1-3/16" Stud \\ (NC both ends)|Carb to Manifold Stud|XLH, XLCH|
|24818-52|1977-1978|Stud 5/16" x (18 x 24) x 1-11/16"|Carb to Manifold Stud|XLH, XLCH|
|24824-67|1967-1969|3/8" x 2" (NC x NF)|Carb Adapter Stud|XLCH|
|24825-66|1966-1971|3/8" x 1-5/8" (NC x NF)|Carb Adapter Stud|XLH, XLCH|
|24827-66|1966-1978|Stud|Air Cleaner Support \\ Bracket Stud|XLH, XLCH|
|24827-66A|1983-1985|Stud|Upper Intake to Carb Stud|XL, XLS, XLX|
|27130-81|1981-1985|Screw|Throttle Stop Screw|XL, XLS|
|27139-81|1981-1985|Screw w/ Washer|Throttle Cable Bracket Screw|XL, XLS|
|27145-81|1981-1985|Screw|Fast Idle Screw|XL, XLS|
|27271-71|1972-E1976|#8-32 Slotted Hex Head Screw|Carb Throttle Stop Screw|XLH, XLCH|
|27286-57|1957-1965|Fillister Head Screw (NF)|Linkert Body Screw|Sportsters|
|27304-76|L1976-1985|Brass Screw with Washer|Carb Choke Cable Bracket Screw|Sportsters|
|27306-76|L1976-1980|Brass Screw|Carb Fast Idle Cam Screw|Sportsters|
|:::|:::|:::|Carb Accel Pump Stop Screw|Sportsters|
|27307-76|L1976-1985|Brass Screw|Choke Wire Block Screw|Sportsters|
|27309-76|L1976-1987|Brass Screw|Float Pin Screw|Sportsters|
|27313-76|L1976-1980|Throttle Stop Screw|Sportsters|
|27315-76|L1976-1978|Screw w/ tapered end|Idle Speed Adjustment Screw|XLH, XLCH|{{ :techtalk:ref:tools:1976l-1978_sportster_carb_idle_speed_adjusting_screw_27315-76_by_robison_motorcycles.jpg?linkonly |Pic1}} ((photos courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|27320-76|L1976-1980|Screw|Throttle Cable Bracket Screw|XLH, XLCH, XLS|
|27342-71|1972-E1976|#1/8-40 Screw with Lock Washer|Choke Plate Screw|XLH, XLCH|
|27351-57|1957-1965|Screw|Linkert Carb Throttle Lever Screw|Sportsters|
|27352-66|1966-1971|Screw|Tillotson Carb \\ Intermediate Speed Adj Screw|XLH, XLCH|
|27358-54|1954-1956|Screw|Venture Retainer Screw|KH|
|27366-76|L1976-1987|Screw|Carb Bowl Screw|Sportsters|
|27367-76|L1976-1987|Screw|Accelerator Pump (long) Screw|Sportsters|
|27377-39|1952-1956|Fillister Head Screw|Carburetor Drain Plug|K Models|
|27377-57|1957-1965|Fillister Head Screw|Carburetor Drain Plug|Sportsters|
|27383-11|1952-1956|Threaded Pin|Float Lever Pin|K Models|
|27396-71|1972-E1976|#4-36 Screw with Lock Washer|Accelerator Pump Lever Screw|XLH, XLCH|
|27424-48|1952-1956|Hex Bolt|Intake Pipe Bolt|K, KH|
|27434-56|1956|Screw|Carb Support Bracket Screw|KH|
|27555-83|L1983-1984|Screw|Throttle Slide Cover Screw|XR-1000|
|27594-76|1983-1984|Screw|Acc Pump Mounting Screw (long) |XL, XLS, XLX|
|27596-66|1966-1971|Screw|Tillotson Carb Fuel Inlet Valve \\ Lever Pin Retaining Screw|XLH, XLCH|
|27641-71|1972-E1976|Screw|Idle Adjusting Screw|XLH, XLCH|{{:techtalk:ref:tools:1972-e1976_sportster_carb_idle_speed_adjusting_screw_27641-71_by_robison_motorcycles.jpg?linkonly|Pic1}} ((photo courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|27686-71|1972-E1976|#8-36 Screw|Throttle Wire Block Screw|XLH, XLCH|
|27688-66|1966-1971|Screw|Intermediate Speed Adj Screw|XLH, XLCH|{{ :techtalk:ih:carb:1966-1971_xlh-xlch_intermediate_speed_adj_screw_by_robison_motorcycles.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|27704-61|1966-1971|Screw|Tillotson Carb Main Jet Plug|XLH, XLCH|
|27717-66|1966-1971|Screw|Tillotson Carb \\ Throttle Lever Stop Screw|XLH, XLCH|
|27720-61|1966-1971|Screw|Tillotson Carb Screw & Lockwasher \\ Choke and Throttle Shutters|
|27739-69|L1983-1984|Screw|Fuel Inlet Fitting Screw|XR-1000|
|27812-66|1966-1971|Screw|Diaphragm Cover Plug Screw|XLH, XLCH|
|27814-66|1966-1971|Screw|Tillotson Diaphragm Cover Ret|XLH, XLCH|
|27884-78|1979|Screw|Low Speed Mixture Screw|XL, XLCH|
|29254-78|1979-1982|5/16" x 18 x 1-1/4" Stud|Carb to \\ Intake Manifold Stud|XL, XLCH, XLS|
|33298-65|L1972-1978|5/16" x (18 x 24) x 1-1/2" Stud|Carb to \\ Manifold Stud|XLH, XLCH|
|33298-65|L1976-1978|5/16" x (18 x 24) x 1-1/2" Stud \\ (NF one end, NC the other)|Carb to Manifold Stud|XLH, XLCH|
|41485-52|1957|Screw|Linkert Choke Lever Bracket|XL|
===== California Emissions Related =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|3787|1985|Bolt| |XL, XLS, XLX|
|8625|1985|Rivet| |XL, XLS, XLX|
====== Exhaust ======
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1205|1975-1976 \\ 1980|#10-24 x 3/4" Pozidriv \\ Fillister Head Screw|Exhaust Crossover Shield Screw|XLH, XLCH \\ XL, XLS|
|1214|1953-1958|#10-24 x 3/4" \\ Fillister Head Screw|Exhaust Shield Clamp Screw|K Models, XL, XLH|
|:::|1965|:::|:::|XLCH|
|1214HW|1954-1958|#10-24 x 3/4" \\ Fillister Head Screw|Exhaust Boot Guard Screw|KH, XL, XLH|
|:::|1965- |:::|:::|XLCH|
|2414W|1962- |5/16" x 18 x 1-1/8" \\ Oval Hd Screw|Dual Exhaust Support Screws|XLH, XLCH|
|2687W|L1970-1976|Socket Head Bolt|Exhaust to Manifold Bolt \\ (independent dual)|XLH, XLCH|
|2708|1981-1982|1/4" x 20 x 3/4" Socket Hd Screw|Exhaust Shield Clamp Screw|XL, XLS|
|2762|1958-1961|#10-32 x 1/2" Round Hd Screw|Exhaust Clamp Bolt|XLH, XLCH|
|2762W|1958-1961|1/4" x 20 x 1/2" Round Hd Screw|Pipe Clamp Screw|XLH, XLCH|
|2762B|1958- |1/4" x 24 x 1/2" Round Hd Screw|Front Exhaust Pipe \\ Clamp Screw|XLH, XLCH|
|2762W|1958-1961|1/4" x 24 x 1/2" Round Hd Screw|Exhaust Pipe Clamp Screw|XLH, XLCH|
|2871 \\ 2871W|1977-1979 \\ 1954-1979|5/16" x 18 x 1-1/4" Hex Hd Bolt|Muffler to Support Bracket Bolt|XL, XLCH, XLS|
|3210|1981-1985|5/16" x 18 x 1-1/4" Socket \\ Fillister Head Screw|Exhaust Clamp Screw|XLH, XLS|
|3738|1962-E1972|1/4" x 28 x 1/2" Hex Head Bolt|Exhaust Clamp Bolt|XLH, XLCH|
|3741|1952- |1/4" x 28 x 1/2" Hex Head Bolt|Exhaust Clamp Bolt|K Models, Sportsters|
|3789 \\ 3789A|L1972-1976|1/4" x 20 x 3/4" Socket \\ Fillister Head Screw|Exhaust Clamp Screw|XLH, XLCH|
|:::|1977-1980 \\ 1957-1978|:::|Exhaust Manifold Clamp Screw|XL, XLCH, XLS|
|3791|1954-E1972|1/4" x 28 x 3/4" Hex Head Bolt|Exhaust Clamp Bolt|KH, Sportsters|
|3834B|1968-1969|3/8" x 16 x 1-1/2" \\ Hex Head Bolt|Muffler Support Bolt|XLH, XLCH|
|3840|1968<1976|1/4" x 28 x 1-1/4" \\ Hex Head Bolt|Dual Muffler \\ Conv. Kit (65433-68) \\ Exhaust Port Clamp Bolt|XLH, XLCH|
|3974HW|1952- |5/16-24" x 3/4" Hex Head Bolt|Exhaust Clamp Bolt|K Models, Sportsters|
|3991|1980-1985|5/16" x18 x 7/8" Hex Head Bolt|Muffler to \\ Support Bracket Bolt|XL, XLS|
|3996|1952- |5/16" x 24 x 7/8" Hex Head Bolt|Exhaust Clamp Bolt|K Models, Sportster|
|4001|1958-1961|5/16" x 24 x 15/16" Hex Hd Bolt|Exhaust Clamp Bolt|XLH, XLCH|
|:::|Year models used on was corrected in the 1968 parts catalog supplement||||
|4012|1965- |5/16" x 24 x 1-1/4" Hex Hd Bolt|Exhaust Bolt|XLH, XLCH|
|4014W|1968-E1970 \\ \\ 1957-1976|5/16" x 24 x 1-1/4" Hex Hd Bolt|Dual Muffler \\ Conv. Kit (65433-68) \\ Muffler Clamp Bolt \\ Muffler Clamp Bolt (dual)|XLH, XLCH|
|:::|1977-1980|:::|Header to Muffler Clamp Bolt|XL, XLCH, XLS|
|4017|L1981-1982|5/16" x 18 x 1" Hex Head Bolt|Crossover Guard Bolt|XL, XLS|
|4020|1962- |5/16" x 24 x 1-3/8" \\ Hex Head Bolt|Exhaust Clamp Bolt|XLH|
|:::|1965- |:::|:::|XLCH|
|4020W|1962- |5/16" x 24 x 1-3/8" \\ Hex head Bolt|Muffler Clamp Bolt|XLH|
|:::|1965- |:::|:::|XLCH|
|4036|1982-1985|5/16" x 24 x 1-1/2" Hex Hd Bolt|Crossover Guard Bolt|XL, XLS|
|4072|1968-1969|5/16" x 24 x 2-5/8" Hex Hd Bolt|Dual Muffler \\ Conv. Kit (65433-68) \\ Muffler to Bracket Bolt|XLCH|
|4082|1968-E1970|5/16" x 24 x 3-1/4"|Dual Muffler \\ Conv. Kit (65433-68) \\ Muffler Clamp Bolt|XLH|
|:::|E1970|:::|:::|XLCH|
|4088|L1983-1984|Bolt|Rear Muffler to \\ Shock Cover Bolt|XR-1000|
|4102B|1968- |5/16" x 18 x 3-1/2" Hex Hd Bolt|Muffler Support Bolt|XLCH|
|4362|1953-1976|3/8" x 24 x 1-3/8" Hex Hd Bolt|Exhaust Clamp Bolt|K Models, Sportsters|
|4374B|1968-E1975|3/8" x 24 x 1-5/8" Hex Hd Bolt|Dual Muffler \\ Conv. Kit (65433-68) \\ Bracket to Frame Bolt|XLH, XLCH|
|4380W|1982-1990|3/8" x 24 x 2" Hex Hd Bolt|Exhaust Support to \\ Frame Bolt|Sportsters|
|4410|L1970-1976|1/4" x 28 x 7/8" Hex Hd Bolt|Exhaust to Manifold Bolt|XLH, XLCH|
|4411|L1975-1976|3/8" x 24 x 1-3/4" Hex Hd Bolt|Exhaust Pipe Support Bolts|XLH, XLCH|
|4719W|1977-1979 \\ 1957-1978|3/8" x 16 x 2-1/2" Hex Hd Bolt|Exhaust Support to \\ Frame Bolt|XL, XLCH, XLS|
|4721|1980-1981 \\ 1983-1984|3/8" x 16 x 1-1/2" Hex Hd Bolt|Exhaust Support to \\ Frame Bolt|XL, XLS, XLX|
|65330-59|1959- |Stud|High Level Muffler Stud|XLCH|
|65711-38|1959- |Screw|Boot Guard Screw|XLCH|
|67729-48|1954-1976|Screw|Exhaust Shield Clamp Screw|KH, XL, XLH|
|:::|1965-1976|:::|:::|XLCH|
|:::|1980|:::|:::|XL, XLS|
====== Electrical ======
===== General Electrical =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|2623W|1970-1974|#8-15 x 5/8" Self Tapping \\ Pan Head Screw|Terminal Plate Screw|XLH, XLCH|
|2635W|1967-1969|#8-32 x 1/2" Round Head Screw|Main Terminal \\ Block Mounting Screw|XLH, XLCH|
|2660|1967-E1973|#10-24 x 3/8" Pozidriv \\ Pan Head Screw|Fuse Holder Clip Screw|XLH|
|:::|1970-E1973|:::|:::|XLCH|
|:::|1973-1975|:::|Main Cable Clamp Screw|XLH, XLCH|
|2669 \\ 2669W|1952-1966|#10-32 x 3/8" Round Head Screw \\ #10-24 x 3/8" Round Head Screw|Electrical Terminal Plate Screw|K Models, XL, XLH|
|2674W|1970-1974|#10-24 x 3/8" Round Head Screw|Main Terminal Block Mounting Screw|XLH, XLCH|
|2684W|1965- |#10-32 x 5/8" Round Head Screw|Ground Wire to Frame Screw|XLH|
|2823|1965-1974|5/16" x 18 x 3/8" Phillips Head Screw|Terminal Plate Mounting Screw|XLH|
|2871W|1970-1974|5/16" x 18 x 1-1/8" Hex Head Bolt|Terminal Plate Screw|XLH, XLCH|
|3420|1965-1966|#6-32 x 7/8" Slotted \\ Hex Head Screw|Rectifier (terminal) Mounting Bolt |XLH|
|3491|1952-1966|#8-32 x 5/8" Hex Head Screw|Electrical Terminal Plate Screw|K Models, XL, XLH|
|4014W|1970-1971|5/16" x 24 x 3/8" Hex Head Bolt|Terminal Plate Bolt \\ (replaced by 4022W in '72)|XLH, XLCH|
|4022W|1970-1974|5/16" x 18 x 1-1/8" Hex Head Bolt|Terminal Plate Bolt \\ (replaced 4014W in'72)|XLH, XLCH|
===== Battery =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|3426|1979-1980|6mm x 22 Phillips Head Screw|Battery Terminal Screw|XL, XLCH, XLS|
|3440|1967-1970 \\ 1972-1978|3/8"-16 x 1/2" Hex Head Bolt\\ (grade 5)|Crankcase Hole Plug|XLCH|
|3444|L1982-1983|1/4" x 20 x 5/8" Socket \\ Fillister Head Screw|Batery Hold Down Strap Screw|XL, XLS|
|3787|1967-1978|1/4" x 20 x 3/4" Hex Head Bolt (NC)|Battery Terminal Bolt|XLH|
|:::|1970-1978|:::|:::|XLCH|
|3956|1952- |5/16" x 24 x 9/16" Hex Head Bolt|Battery Box Bolt|K Models, Sportsters|
|3956|1967-1978|5/16" x 24 x 9/16" Hex Head Bolt|Battery Carrier Bolt|XLH|
|4000|1952-1964|5/16" x 24 x 1" Hex Head Bolt|Battery Box Bracket Bolt|K Models, XL, XLH|
|4293|1967- |3/8" x 16 x 7/8" Hex Head Bolt|Battery Support Bracket Bolt|XLH|
|4348|1953-1966|3/8" x 16 x 1-3/16" Hex Head Bolt|Battery Box Bolt|K Models, XL, XLH|
|4391|1982-1990|5/16" x 24 x 5/8" Hex Head Bolt|Battery Tray Mounting Bolt|Sportsters|
|4713W|1967-1978|3/18" x 16 x 3/4" Hex Head Bolt|Battery Box Bracket Bolt|XLH|
|33088-64|1967-1970|3/8" x 16 x 7/16" Hex Head Bolt|Crankcase Hole Plug|XLCH|
|62563-65|1967- |Rubber Mounted Threaded Stud|Battery Carrier Stud|XLH|
|:::|1970- |:::|:::|XLCH|
|66000-80|1979-1990|Battery Terminal Screw Kit|Sportsters|
|66111-70|1970-1978|Screw Kit|Battery Terminal Screw Kit|XLCH|
|66112-23|1954-1964|Screw|Battery Terminal Screw|KH, XL, XLH|
|66387-26|1954-1964|Wing Nut|Battery Cover Wing Nut|KH, XL, XLH|
===== Generator =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|993|1957|#6-32 x 1/4" Fillister Head Screw|Generator Field Coil Screw|XL|
|993W|1954-1957|:::|Generator Wire Terminal Screw \\ (Replaced 9993 in '66)|KH, XL|
|1202|1953-1957|#10-32 x 1/2" Fillister Head Screw|Generator Brush Holder Screw|K Models, XL|
|1202W|1954-1957|#10-32 x 1/2" Fillister Head Screw \\ (Replaced 1202 in '66)|Generator Brush Screw|KH, XL|
|1210|1953-1957|#10-32 x 5/8" Fillister Head Screw|Generator End Cover Commutator \\ Outer Oil Retainer Screw|K Models, XL|
|1210HW|1954-1957|#10-32 x 5/8" Screw|Generator End Cover Screw \\ (Replaced 1210 in '66)|KH, XL|
|1374|1966-1981|1/4" x 28 x 3/4" Pozidriv \\ Pan Head Screw|Generator Cover Clamp Screw|XLH, XLCH, XLS|
|2587|1958|#10-32 x 5/8" Pozidriv \\ Pan Head Screw|Generator Brush Screw|XLH|
|:::|1959-1981|:::|:::|XLH, XLCH, XLS|
|2656W|1958|#10 x 3/8" Self Tapping \\ Pan Head Screw|Generator Cover Screw|XLH|
|:::|1959-1981|:::|:::|XLH, XLCH, XLS|
|2684W|1958|#10-32 x 5/8" Round Head Screw|Generator Brush Holder \\ Plate Screw|XLH|
|:::|1959- |:::|:::|XLH, XLCH|
|2690W|1958|#10-32 x 7/8" Square Head Screw|Generator Terminal Bolt Clip Screw|XLH|
|:::|1959-1981|:::|:::|XLH, XLCH, XLS|
|2772|1966- |1/4" x 28 x 3/4" Round Head Screw|Generator Brush Cover Screw|XLH, XLCH|
|3469|1979-1981|5/16" x 24 x 3-1/4" Hex Head Bolt|Generator End Plate Bolt|XLS|
|29903-82|1982-E1984|Screw w/ Washer|Generator Brush Screw|XL, XLS|
|29904-82|1982-E1984|Screw|Generator Field \\ Coil Wire Screw|XL, XLS|
|29905-82|1982-E1984|Screw (long)|Generator Thru Bolt|XL, XLS|
|30012-32|1952-1957|Long Bolt|Generator Frame Screw|K Models, XL|
|30012-52|1952-1957|Long Bolt|Generator Frame Screw|K Models, XL|
|30012-58|1958|Long Bolt|Generator Frame Screw|XLH|
|:::|1959-1981|:::|:::|XLH, XLCH|
|30013-52|1952-1958|5/16" x 24 Bolt|Generator Mounting Bolt|K Models, XL, XLH|
|:::|1959-1970|:::|:::|XLH, XLCH|
|30013-71|1971-E1984|5/16" x 24 x 3-1/4" Hex Head Bolt|Generator Mounting Bolt|XL, XLH, XLCH|
|30280-18|1952-1957|Screw|Generator Pole Piece Screw|K Models, XL|
|30280-58|1958|Screw|Generator Pole Piece Screw|XLH|
|:::|1959-1981|:::|:::|XLH, XLCH, XLS|
|30460-32|1952-1957|Screw|Generator Positive Terminal Screw|K Models, XL|
===== Voltage Regulator =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|N/A| |#8 x 1-1/2 Screw|Voltage Regulator Cap Screw ((brucstoudt of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/156767-voltage-regulator-mounting-and-fasteners/page5?t=1677718&page=5))|XLCH|
|1063 \\ 1063W|1952-1964|#8-32 x 3/8" Fillister Head Screw \\ (NC, White)|Voltage Regulator Terminal Screw|K Models, Sportsters|
|:::|1954-1964|:::|Voltage Regulator Terminal Screw|K Models, Sportsters|
|1205|1982-1990|#10-24 x 3/4" Pozidriv \\ Fillister Head Screw|Voltage Regulator Mounting Bolt|Sportsters|
|3720|1956-1962|1/4" x 28 x 7/16" Hex Head Bolt|Voltage Regulator Mounting Bolt|KH, XLC, XLCH|
|3738|1952-1964|1/4" x 20 x 1/2" Hex Head Bolt|Voltage Regulator Mounting Bolt|K Models, Sportsters|
|3787|1978-1981|1/4" x 20 x 3/4" Hex Head Bolt|Voltage Regulator Mounting Bolt|XLH, XLCH|
|3791|1965-1966|1/4" x 28 x 3/4" Hex Head Bolt|Voltage Regulator Mounting Bolt|XLH|
|:::|1965-1975|:::|:::|XLCH|
|4410|1965-1976|1/4" x 28 x 7/8" Hex Head Bolt|Voltage Regulator Mounting Bolt|XLH, XLCH|
|74516-55|1955-1964|Screw|Voltage Regulator Cover Screw|KH, XL, XLH|
|:::|1959-1964|:::|:::|XLCH|
===== Stator =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|2547|L1984-1985|#10-24 x 3/8" Socket Head Screw|Stator Mounting Adapter to \\ Engine Screw|XL, XLS, XLX|
|2653|L1984|#10-24 x 7/8" Fillister Head Screw|Stator to Mounting Adapter Screw|XL, XLS, XLX|
|2712|1985-1990|#10-24 x 7/8" Torx Cap Head Screw|Stator to Engine Screw|Sportsters|
===== Headlight / Spotlight =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1073W|1963-* |#8-32 x 3/4" Fillister Head Screw|Headlight Bezel Screw|XLCH|
|:::|1967-- |:::|:::|XLH|
|1074W|1963-E1975 \\ 1967-E1975|#8-32 x 7/8" Fillister Head Screw|Headlight Bezel Screw|XLCH \\ XLH|
|1203|1979-1990|#8-32 x 7/8" Pozidriv \\ Fillister Head Screw|Headlight Bezel Screw|Sportsters|
|2585|1954-1966|#8-32 x 5/16" Pozidriv \\ Pan Head Screw|Handlebar Spotlight \\ Switch Clamp Screw|KH, XL, XLH|
|2629|1963-- |#8-32 x 5/16" Round Head Screw|Headlight Terminal Plate Screw|XLCH|
|:::|1967-- |:::|:::|XLH|
|2629|1952-1966|#8-32 x 5/16" Round Head Screw|Spotlight Switch Wire Clamp Screw|K Models, XL, XLH|
|2638|1962- |#8-32 x 5/8" Round Head Screw|Spotlight Molding Ring Screw|XLH|
|2837W|1967-- |5/16" x 24 x 5/8" Phillips Head Screw|Headlight Housing Screw|XLH|
|2871W|1970-E1977 \\ 1979-1985|5/16" x 18 x 1-1/8" Hex Head Bolt|Headlamp Bracket Bolt|XLH, XLCH, XLS|
|3953W|1952-1966|5/16" x 24 x 1/2" Hex Head Bolt \\ (Grade 5, Cadmium)|L-R Spotlight Bracket Bolt|K Models, XL, XLH|
|3956|1952-1966|5/16" x 24 x 9/16" Hex Head Bolt|L-R Spotlight Bracket Bolt|K Models, XL, XLH|
|3960W|1963-1969|5/16" x 24 x 1" Hex Head Bolt|Headlamp Bracket Bolt|XLCH|
|3960W|1954-1966|5/16" x 24 x 1" Hex Head Bolt|Spotlight Bracket Bolt|KH, XL, XLCH|
|3974HW|1959-1962|5/16-24" x 3/4" Hex Head Bolt|Headlamp Bracket Bolt|XLCH|
|:::|1967-1969|:::|:::|XLH|
|3996|1963|5/16" x 24 x 7/8" Hex Head Bolt|Headlamp Bracket Bolt \\ Replaced by #4000 Bolt|XLCH|
|4000|1954-1966|5/16" x 24 x 1" Hex Head Bolt|L-R Spotlight Bracket Bolt \\ (replaced by 3960W in '78)|KH, XL, XLCH|
|4000|1963-1969|5/16" x 24 x 1" Hex Head Bolt|Headlamp Bracket Bolt \\ (replaced 3996)|XLCH|
|4014W|1970-1971|5/16" x 24 x 1-1/4" Hex Head Bolt|Headlamp Bracket Bolt \\ (replaced by 4022W in'72)|XLH, XLCH|
|4022W|1972-1976|5/16" x 18 x 1-1/8" Hex Head Bolt|Headlamp Bracket Bolt \\ (replaced 4014W)|XLH, XLCH|
|43868-72|L1977-1978|5/16" x 18 x 1-1/8" Hex Head Bolt|Headlamp Bracket Bolt|XL, XLCH|
|67715-59|1959-1974|Screw|Headlamp Door Screw|XLH|
|:::|1959-1962|:::|:::|XLCH|
|67721-48|1952-1958|Screw|Headlamp Cover Screw|K, KH, XL, XLCH|
|67729-48|1953-1958|Screw|Headlamp Cover Molding Screw|K, KH, XL, XLH|
|67817-52|1952-1966|Bolt|Headlamp Mounting Bolt|K Models, XL, XLH|
|68672-38|1956-1966 \\ L1975-1980|#8-32 x 3/4" Fillister Head Screw|Spotlight Cover Screw|KH, XL, XLH \\ XLH, XLCH, XLS|
|68684-38|1954-1961|Screw|Spotlight Focus Screw|KH, XL, XLH|
|68692-38|1952-1961|Special Swivel Eyelet Bolt|Spotlight Swivel Bolt|K, KH, XL, XLH|
|68696-33|1952-1961|Thru Bolt for Swivel Mount Bolt|K, KH, XL, XLH|
===== Stoplight / Turn Signals =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1190W|1967- |#10-32 x 3/8" \\ Fillister Head Screw|Rear Turns Cable Clamp Screw|XLH|
|1369|1957-1962|1/4" x 20 11/16" \\ Fillister Head Screw|Turn Signal Pilot \\ Lamp Bracket Screw|XL, XLH|
|2073W|L1963-E1973|#4-24 x 1/4" \\ Self Tapping Screw|Flasher Terminal Screw|XLH, XLCH|
|2215|1968- \\ 1970-|#10 x 24 x 9/16" Screw|Front Fender Lamp Base Screw|XLH \\ XLCH|
|2585|1957-E1973|#8-32 x 5/16" Pozidriv \\ Pan Head Screw|Toggle Switch Mounting Screw|XL, XLH|
|2587|1968-1973 \\ 1970-1973|#10-32 x 5/8" Pozidriv \\ Pan Head Screw|Flasher Clamp Screw|XLH, XLCH|
|2593|1968-1969|#10-32 x 1/4" Pozidriv \\ Pan Head Screw|Flasher Clamp Screw|XLH|
|2612|1956-1972|#8-32 x 1/2" Pozidriv \\ Pan Head Screw|Tail Lamp Bracket Screw|KH, XL, XLH, XLCH|
|2629|1957- |#8-32 x 5/16" Round Head Screw|Turn Signal Switch \\ Mounting Screw|XL, XLH|
|2629|1952-1966|#8-32 x 5/16" Round Head Screw|Stoplight Switch \\ Insulator Screw|K Models, Sportsters|
|2630W|1968- \\ 1970- |#8-32 x 5/16" Self Tapping \\ Round Head Screw|Lens Screw|XLH \\ XLCH|
|2635|1956-1958|#8-32 x 1/2" Round Head Screw|Tail Lamp Screw|KH, XL, XLH|
|:::|1959- |:::|:::|XLH, XLCH|
|2635W|1956- |#8-32 x 1/2" Round Head Screw|Taillight Socket Screw|KH, Sportsters|
|2660|1967-E1973 \\ 1970-E1973|#10-24 x 3/8" Pozidriv \\ Pan Head Screw|Flasher Clamp Bracket Screw|XLH \\ XLCH|
|2661W|1963-1964|#10-24 x 5/8" Round Head Screw \\ #10-24 x 1/2" Self Tapping \\ Phillips Head Screw ('71)|Front Turn Signal \\ to Bracket Screw|XLH|
|2670W|L1965- |#10-24 x 3/8" Socket Head Screw|Rear Turn Signal Lamp Screw|XLH|
|2674W|1965- |#10-24 x 3/8 Phillips Head Screw|Turn Signal Bracket Screw|XL, XLH|
|:::|L1965- |:::|Front Turn Signal Lamp Screw|XLH|
|:::|1967-1969|:::|Rear Turn Signal \\ Harness Clamp Screw|XLH|
|2686|1968- \\ 1970- |#10-24 x 7/8" Round Head Screw|Front Fender Lamp \\ Terminal Screw|XLH \\ XLCH|
|2691W|L1965- \\ 1970- |#10-24 x 1/2" Phillips Head Screw|Lamp Screw|XLH \\ XLCH|
|2692W|L1965- \\ 1970- |#10-24 x 1/2" Socket Head Screw|Lamp Screw|XLH \\ XLCH|
|2698|L1973-1979|5/16" x 24 x 2-1/4" \\ Socket Head Screw|Turn Signal Lamp \\ Mounting Screw|XLH, XLCH, XLT|
|2698|1979-1990|5/16" x 24 x 5/8" \\ Socket Head Screw|Rear Turn Signal \\ Standoff Screw|Sportsters|
|2701|L1973- |3/8" x 24 x 2-1/4" Socket \\ Fillister Head Screw|Turn Signal Support Screw|XLH, XLCH|
|2768|1953-1955|1/4" x 24 x 5/8" Round Head Screw|Tail Lamp Mounting Screw|K, KH|
|2768B|1954-1955|1/4" x 24 x 5/8" Round Head Screw|Tail Lamp Mounting Screw|KH|
|2791W|1959-1966|1/4" x 20 x 1-1/4" \\ Round Head Screw| |XLCH|
|2889|L1973-1978|3/8" x 24 x 3/4" Hex Head Bolt|Turn Signal Support Bolt|XLH, XLCH|
|3005W|1968- \\ 1970- |#6-32 x 3/16" \\ Self Tapping Screw|Lamp Socket Screw|XLH \\ XLCH|
|3416|1979-1984|3/8" x 24 x 1-1/2" Hex Head Bolt|Rear Turns Standoff to \\ Fender Mounting Bolt|XL, XLCH, XLS|
|3430|E1983|5/16" x 24 x 5" Hex Head Bolt|Turn Signal Standoff Thru Bolt|XLS|
|3491|1968- \\ 1970- |#8-32 x 5/8" Hex Head Screw|Fender Cable Screw|XLH \\ XLCH|
|3728|1963-1978 \\ 1970-1978|1/4" x 20 x 1/2" Hex Head Bolt|Turn Signal \\ Mounting Bracket Bolt|XLH, XLT \\ XLCH|
|3767B|1983-1990|1/4" x 20 x 5/8" Hex Head Bolt|Turn Signal Ground Wire Bolt|Sportsters|
|3791|1957-1962 \\ 1970-1972|1/4" x 28 x 3/4" Hex Head Bolt|Rear Turn Signal \\ Mounting Bracket Bolt|XL, XLH \\ XLH, XLCH|
|3840|1963|1/4" x 28 x 1-1/4" Hex Head Bolt|Stoplight Switch Mounting Bolt|XLCH|
|3945|1977|3/8" x 24 x 2-1/4" Hex Head Bolt|Turn Signal Mounting Bolt \\ (kit 68573-77)|XLT|
|3956|1957-E1973 \\ 1970-E1973|5/16" x 24 x 9/16" Hex Head Bolt|Turn Signal to Bracket Bolt|XL, XLH \\ XLH, XLCH|
|3959|1952-1966|5/16" x 18" x 9/16" Hex Head Bolt|Stoplight Switch \\ Bracket Bolt|K Models, XL, XLH|
|:::|1959-1966|:::|:::|XLCH|
|4069|1982-1985 \\ 1986-1987|1/4" x 20 x 3/4" Hex \\ Socket Head Screw|Front Turns \\ Handlebar Clamp Screw|XL, XLS \\ Sportsters|
|4070|1982-1987 \\ 1986-1987|5/16" x 24 x 2-1/4" Hex \\ Socket Head Screw|Front Turns \\ Handlebar Clamp Screw|Sportsters|
|4391|L1983-1985|5/16" x 24 x 5/8" Hex Head Bolt|Turn Signal \\ Mounting Clamp Bolt|XLS|
|4410|1957-1962 \\ 1970-E1973|1/4" x 28 x 7/8" Hex Head Bolt|Rear Turn Signal \\ Mounting Bracket Bolt|XL, XLH \\ XLH, XLCH|
|4724|1983-1989|3/8" x 24 x 1-1/2" Hex Head Bolt|Rear Turns Standoff to \\ Fender Mounting Bolt|Sportsters|
|30013-71|L1983-1985|5/16" x 24 x 3-1/4" Hex Head Bolt|Turn Signal Standoff \\ Thru Bolt|XLS|
|67715-59|1970-1971|Screw|Tail Lamp Bezel Screw|XLH, XLCH|
|68026-73|L1973-1990|Screw|Tail Light Lamp Screw|Sportsters|
|68119-55|1956-1972|Screw|Tail Lamp Outlook \\ Lens Screw|KH, XL, XLH|
|:::|1959-1972|:::|:::|XLH, XLCH|
|68119-69|1969-1972|Screw|Tail Lamp Outlook \\ Lens Screw|XLH, XLCH|
|68131-70|1970-1971|Screw|Taillight License Lamp Screw|XLH, XLCH|
|68478-73|L1973-1981|#10-24 x 3/4" \\ Socket Head Screw|Front Turn Signal \\ Handlebar Mount Screw|XLH, XLCH, XLS|
|68479-73|L1973-1981|5/16" x 24 x 2" \\ Socket Head Screw|Front Turn Signal \\ Handlebar Mount Screw|XLH, XLCH|
|68482-73|L1973-1985|Screw|Turn Signal Lens Screw|XLH, XLCH, XLS|
|68522-38|1957-1962|Screw|Turn Signal Lamp Door Screw|XL, XLH|
|68528-77A|1979-1980|Stud (w/ spacer)|Rear Turns Standoff|XLS|
|68586-63|1963-1975 \\ 1970-1975|Screw|Turn Signal Lens \\ Mounting Screw|XLH \\ XLCH|
|68672-38|1956-1958|Screw|Tail Lamp Cover Screw|KH, XL, XLH|
|68672-38|1959-1972|Screw|Tail Light Mounting Screw|XLH, XLCH|
===== Flasher / Hazard =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1190W|1968-? |#10-32 x 3/8" \\ Fillister Head Screw|Hazard Warning \\ Flasher Kit (68541-68) \\ Clamp Screw|XLH|
|2073W|L1963-1965|#4-40 Self Tapping Screw|Two Terminal Flasher Screw|XLH|
|:::|1968-1972|:::|Hazard Warning \\ Flasher Kit (68541-68) \\ Flasher Terminal Screw|XLH|
|2627W|1957-1958|#8-32 x 3/16" Round Head Screw|Turn Signal Flasher \\ Bracket Screw|XL, XLH|
|2663B|1968-1969|#10-32 x 1/4" Round Head Screw|Hazard Warning \\ Flasher Kit (68541-68) \\ Clip Screw|XLH|
|2684W|1968- \\ 1970- |#10-32 x 5/8" Round Head Screw|Flasher Bracket Screw|XLH \\ XLCH|
===== Horn =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1229|1961|#10-32 x 1" \\ Fillister Head Screw|Horn Cover Screw \\ (replaced 69146-61)|XLCH|
|1229W|1961|#10-32 x 1" \\ Fillister Head Screw|Horn Cover Screw \\ (replaced 1229)|XLCH|
|1719W|1965-1985|#8-32 x 5/8" \\ Phillips Head Screw|Horn Cover Screw|XLH, XLCH, XLS|
|1778P|1959-1964|Slotted Screw|Horn Terminal Screw|XLCH|
|2204W|1955-1956|#10-32 x 3/8" \\ Countersunk Head Screw|Horn Cover Screw|KH|
|2210|1953-1963|#10-32 x 1/2" \\ Countersunk Head Screw (NF)|Horn Cover Screw|KH, XL, XLCH|
|:::|This Screw replaced by 2210W in 1964||||
|2210W|1953-1954|#10-32 x 1/2" Countersunk Screw|Horn Cover Screw|KH|
|:::|1957-1964|:::|:::|XL, XLCH|
|2585|L1966-1976|#8-32 x 5/16” Pozidriv \\ Pan Head Screw|Siren Screen Cover Screw|XLH|
|2629|1962- |#8-32 x 5/16" Round Head Screw|Horn Terminal Screw \\ Replaced by 2632 in 1964|XLCH|
|2632|1962-1964|#8-32 x 7/6" Round Head Screw|Horn Terminal Screw|XLCH|
|2632W|1962-1964|#8-32 x 7/16" Round Head Screw|Horn Terminal Screw|XLCH|
|2684W|1963-1969|#10-32 x 5/8" Round Head Screw|Horn Capacitor Mounting Screw|XLCH|
|3206B|1970-1985|#8-32 x 3/16" \\ Socket Head Set Screw|Twin Horn Kit \\ Cable Clamp Screw|XLH, XLCH, XLS|
|3233|L1966-1976|1/4" x 28 x 1/4" Set Screw|Siren Deflector Set Screw|XLH|
|3427|L1983-1984|5/16" x 18 x 3-1/2" \\ Hex Head Bolt (grade 5)|Horn Mounting Bolt|XR-1000|
|3825|1953-1954|1/4" x 28 x 1" Hex Head Bolt|Trumpet Horn Mounting Screw|K, KH|
|3971|1952- |5/16" x 24 x 3/4" Hex Head Bolt|Horn Mounting Bolt|K Models, Sportsters|
|3791|1954-1964|1/4" x 28 x 3/4" Hex Head Bolt|Horn Bracket Bolt|KH, Sportsters|
|4012|1957-1964|5/16" x 24 x 1-1/8" Hex Head Bolt|Trumpet Mounting Bolt|XL, XLH|
|69022-31|1959-1961|Screw|Trumpet Diaphragm Screw|XLCH|
|69030-31|1959-1961|Screw|Horn Terminal Screw|XLCH|
|69038-31|1959-1961|Set Screw|Horn Adjusting Screw|XLCH|
|69146-61|1961-1963|Screw|Horn Cover Screw \\ (replaced by 1229 in 1964|XLCH|
|91263-61|L1966-1976|Stud|Siren Foot Control Stud|XLH|
===== Switches =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1713|1970-1978|#8-32 x 5/16" \\ Countersunk Head Screw|Circuit Breaker \\ Mounting Screw|XLH|
|2508|1982-1990|#10-32 x 9/16" Hex \\ Socket Head Screw|Handlebar Switch Housing Screw|Sportsters|
|2571W|1952-1958|#6-32 x 1/4" Round Head Screw|Ignition Switch \\ Mounting Screw|K, KH, XL, XLH|
|2573W|1967-1969 \\ 1970-1972|#6 Self Tapping \\ Hex Head Screw|Circuit Breaker \\ Mounting Screw|XLH \\ XLCH|
|2585|1966-1978 \\ 1070-1978|#8-32 x 5/16" Pozidriv \\ Pan Head Screw|Ignition Switch \\ Terminal Screw|XLH \\ XLCH|
|2594|1963-1969|#8-32 x 1/4" Pozidriv \\ Pan Head Screw|Headlight Toggle Switch \\ Terminal Screw|XLCH|
|:::|1954-1972 \\ 1963-1972|:::|Handlebar Switch Screw|XLH \\ XLCH|
|2602|1959-1966|1/4" x 20 x 1-1/4" Pozidriv \\ Pan Head Screw|Stoplight Switch Bracket Screw|XLCH|
|2604|1975-1976|#10-32 x 1/2" Pozidriv \\ Pan Head Screw|Stoplight Bracket Switch|XLH, XLCH|
|2622|1966-1978 \\ 1970-1978|#8-32 x 7/16" Pozidriv \\ Pan Head Screw|Ignition Switch Terminal Screw|XLH \\ XLCH|
|2626|1963-* |#8-32 x 1/4" Round Head Screw|Horn Toggle Switch \\ Terminal Screw|XLCH|
|2626|1953-* |#8-32 x 1/4" Round Head Screw|Handlebar Horn Switch Screw|K, KH, XLH|
|:::|1963|:::|:::|XLCH|
|2626|1954-- |#8-32 x 1/4" Round Head Screw|Handlebar Switch Cover Screw|KH, XLH|
|:::|1963-- |:::|:::|XLCH|
|2626 \\ 2626W|1963-1969|#8-32 x 1/4" Round Head Screw|Headlight Toggle Switch \\ Terminal Screw|XLCH|
|2629|1959-1976|#8-32 x 5/16" Round Head Screw|Ignition Switch Terminals \\ (replaced 2632W in '73)|XLH|
|:::|1970-1976|:::|:::|XLCH|
|2632W|1966-1972|#8-32 x 7/16" Round Head Screw|Ignition Switch Terminal Screw \\ (replaced by 2629 in '73)|XLH|
|:::|1970-1972|:::|:::|XLCH|
|2636W|1954-1976|#8-32 x 5/16" Round Head Screw|Stoplight Switch Insulator Bolt|KH, XL, XLH, XLCH|
|2661W|1980-1983|#10-24 x 1/2" Self Tapping \\ Phillips Head Screw|Starter Relay Ground Screw|XL, XLS|
|2662W|1984-1985|#10-24 x 3/8" Self Tapping \\ Phillips Head Screw|Starter Relay Ground Screw|XL, XLS, XLX|
|2695W|1973-1981|#10-24 x 1-1/8" Pozidriv \\ Fillister Head Screw|Handlebar Switch Housing Screw|XLH, XLCH, XLS|
|2748B|1953-1958|1/4" x 28 x 25/64" Round Head Screw|Ignition Switch Bracket Screw|K Models, XL, XLH|
|2763|1967-E1971 \\ 1970-E1971|1/4" x 28 x 1/2" Round Head Screw|Ignition Switch Cover \\ Mounting Screw|XLH \\ XLCH|
|2765W|1967-E1968|1/4" x 20 x 5/8" Round Head Screw|Relay Mounting Screw|XLH|
|:::|L1971-1976|:::|:::|:::|
|2773|1973-1978|1/4" x 20 x 1/2" Pozidriv Head Screw|Starter Relay Mounting Screw|XLH|
|2791W|1959-1966|1/4" x 20 x 1-1/4" Round Head Screw| |XLCH|
|2803W|1973-1981|#6-32 x 1/4" Posidriv \\ Pan Head Screw|Handlebar Switch Button \\ Retainer Screw|XLH, XLCH, XLS|
|2804W|1973-1981|#6-32 x 1/2" Posidriv \\ Pan Head Screw|Handlebar Rocker Switch \\ Mounting Screw|XLH, XLCH, XLS|
|3581|1982-1985|#10-24 x 3/8" Bolt| |XL, XLS|
|3738|1970-1976 \\ 1970-1974|1/4" x 20 x 5/8" Hex Head Bolt|Stoplight Switch Mounting Bolt|XLH \\ XLCH|
|4319|L1983-1984|3/8" x 24 x 1" \\ Hex Head Bolt (grade 5)|Ignition Switch Cover Bolt|XR-1000|
|3802W|1967-1981|1/4" x 20 x 7/8" Hex Head Bolt|Starter Solenoid \\ Mounting Bolt|XL, XLH, XLS|
|3959|1954-1966 \\ 1959-1966|5/16" x 18 x 9/16" Hex Head Bolt|Stoplight Switch \\ Mounting Bolt|KH, XL, XLH \\ XLCH|
|5410|L1983-1984|5/16" x 24 x 1/2" Pozidriv \\ Truss Head Screw (grade 2)|Ignition Switch Cover Screw|XR-1000|
|71504-55|1959-1962|Set Screw|Ignition Switch Knob|XLCH|
|71518-80|1979-1990|Screw w/ Washer|Ignition Switch Terminal Screw|Sportsters|
===== Gauges =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1080|1955-1958|#8-32 x 1" Fillister Head Screw|Speedometer Rear Mounting Screws|KH, XL, XLH|
|1080B|1955-1958|#8-32 x 1" Fillister Head Screw|Speedo/Tach \\ Rubber Mount Screw|KH, XL, XLH|
|1205|1975-1978|#10-24 x 3/4" Pozidriv \\ Fillister Head Screw|Oil Pressure Gauge Kit (74400-68) \\ Handlebar Clamp Screw \\ (replaced 1206W in '75)|XLH, XLCH|
|:::|1979-1981|:::|Oil Pressure, Voltmeter, \\ Temp Gauge Housing Screw \\ Handlebar Clamp Screw|XL, XLCH, XLS|
|1206W|1968-1974|#10-24 x 3/4" Fillister Head Screw|Oil Pressure Gauge Kit (74400-68) \\ Handlebar Clamp Screw \\ (replaced by 1205 in '75)|XLH, XLCH|
|:::|:::|:::|From Ammeter Kit (74440-68) \\ Handlebar Clamp Screw|XLH, XLCH|
|1769W|1968-1974|#10-24 x 1" Round Head Screw|Ammeter Kit (74440-68) \\ Rear Housing Screw|XLH, XLCH|
|1950B|1953-1966|5/16" 24 x 7/16" \\ Countersunk Head Screw|Speedo/Tach \\ Mounting Bracket Screw|K Models, XL, XLH|
|2575W|1965-1976|#6-32 x 7/8" Round Head Screw|Fuel Reserve Warning Light Screw|XLH, XLCH|
|2585|1965-1973|#8-32 x 5/16" Pozidriv \\ Pan Head Screw|Tach Cable Clamp Screw|XLCH|
|2591|1968-1978|#10-32 x 1-3/4" Pozidriv \\ Pan Head Screw|Gauge to Housing Center Screw|XLH, XLCH|
|2595|1968-1978|#10-24 x 1" Pozidriv \\ Pan Head Screw|Gauge to Housing Center Screw|XLH, XLCH|
|2629|1965- |#8-32 x 5/16" Round Head Screw|Tach Cable to Frame Screw|XLCH|
|2630W|1965|#8-32 x 5/16" Self Tapping \\ Round Head Screw|Speedo/Tach Mounting Clip Screw|XLCH|
|:::|1957-1970 \\ 1965 \\ L1969-1970|:::|Circuit Breaker Cover Screw|XLH \\ XLCH \\ XLCH|
|2633|1952-1972|#8-32 x 3/8" Self Tapping \\ Round Head Screw (NC)|Tach Cable Clamp Screw|K Models, Sportsters|
|2660|1968-1978|#10-24 x 3/8" Pozidriv \\ Pan Head Screw|Oil Pressure Gauge Housing Screw|XLH, XLCH|
|:::|1979-1981|:::|Gauge to Housing (inner) Screw|XL, XLCH, XLS|
|2665|1979-1981|#10-32 x 5/8" Pozidriv \\ Pan Head Screw|Gauge to Housing (outer) Screw|XL, XLCH, XLS|
|2672|1952-1958|#10-24 x 1/2" Round Head Screw|Speedometer Cable Clip Screw|K Models, XL, XLH|
|2674W|1968-1974|#10-24 x 3/8 Phillips Head Screw|Ammeter Kit (74440-68) \\ Bracket and Terminal Screw|XLH, XLCH|
|:::|:::|:::|Oil Pressure Gauge Kit (74400-68) \\ Ammeter Bracket Screw|XLH, XLCH|
|2677|1965- |#10 x 1/2" Self Tapping Screw|Speedo/Tach Cable Bracket Screw|XLCH|
|2677|1954-1958|#10-24 x 1/2" Round Head Screw|Speedo/Tach Cable Clip Screw|KH, XL, XLH|
|2705W|1968-1974|#10-32 x 1-3/4" Round Head Screw|Oil Pressure Gauge Kit (74400-68) \\ Handlebar Clamp Screw|XLH, XLCH|
|2731W|1965- |#10 x 3/8" Self Tapping \\ Phillips Head Screw|Speedo/Tach Cable Bracket Screw \\ (Replaced by #2677)|XLCH|
|2748B|1957- |1/4" x 28 x 25/64" Round Head Screw|Speedometer Mounting Screw|K, KH|
|2748B|1965-1966|1/4" x 20 x 1/2" Phillips Head Screw|Tach Cable Clip Bracket Screw|XLCH|
|2808|L1969-1973|#8-32 x 3/8" Pozidriv \\ Pan Head Screw|Speedometer Cable Clamp Screw|XLH, XLCH|
|:::|1979-1985|:::|Throttle or Tach Cable \\ to Frame Clamp Screw|XL, XLCH, XLS|
|3955W|1965-1966|5/16" x 24 x 1/2" Hex Head Bolt|Speedo/Tach Mounting Bracket Bolt \\ (fork mounted)|XLCH|
|3956|1965|5/16" x 24 x 9/16" Hex Head Bolt|Tach Cable Guide Wire Clip Bolt|XLCH|
|3991|1979-1982|5/16" x 18 x 7/8" Hex Head Bolt|Speedometer / Tach \\ Mounting Bracket Bolt|XLS|
|4337W|1973|3/8" x 24 x 1-1/4" Hex Head Bolt|Sppedometer Supprt Bracket Bolt|XLH, XLCH|
|67195-67P|1970-1973|Screw|Reset Cable to \\ Speedometer Screw|XLH, XLCH|
|74407-71|1965-1974|Screw|Fuel Reserve Warning Light Screw|XLH, XLCH|
|92088-65|1965- |Stud Mounted in a 'C' Bracket|Tach Spacer Stud (fork mounted)|XLCH|
====== Engine Control ======
\\
===== Ignition / Spark Coil =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|2667|E1982 \\ 1982-1983|5/16" x 18 x 2" Hex Head Bolt|Coil / Gas Tank \\ Bracket to Frame Screw|XL \\ XLS, XLX|
|2684W|1965-- |#10-32 x 5/8" Round Head Screw|Spark Coil \\ Condenser Mounting Screw|XLCH|
|2823|1952-1966|5/16" x 18 x 3/8" Recessed \\ Truss Head Screw|Spark Coil Cover \\ Mounting Screw|K Models, XL, XLH|
|3826|1954-1964|1/4" x 28 x 1-1/4" Hex Head Screw|Ignition Coil Mounting Bolt|KH, XL, XLH|
|:::|1973-1981|1/4" x 28 x 1-1/4" Hex Head Screw|Ignition Coil to Bracket Bolt|XLH, XLCH, XLS|
|:::|L1982-1985|1/4" x 28 x 1-1/4" Hex Head Screw|Ignition Coil to Bracket Bolt|XL|
|:::|1983-1985|:::|Ignition Coil Bracket Bolt|XLS, XLX|
|3956|1967-1970 \\ 1970|5/16" x 24 x 9/16" Hex Head Bolt|Coil Bracket Mounting Bolt \\ (used with coil \\ 31609-65, 31609-65A)|XLH \\ XLCH|
|:::|1971-1972|:::|:::|XLH, XLCH|
|3974|1967- |5/16" x 24 x 3/4" Hex Head Bolt|Ignition Coil (31609-65) \\ Mounting Bracket Bolt|XLH|
|3993|1982-1990|1/4" x 20 x 1-1/4" Hex Head Bolt|Ignition Coil \\ to Bracket Bolt|Sportsters|
|4086|L1982|5/16“ x 18 x 3” Hex Head Bolt|Coil / Gas Tank Bracket \\ to Frame Screw|XL \\ XLS|
|4710|1977|5/16" x 18 x 2-1/4" Hex Head Bolt|Coil Mounting Bolt|XLT|
|64611-52|1952-1954|Hex Stud Threaded 5/16" x 18|Lower Coil Mounting Stud|K, KH|
|64611-55|1955-1966|Hex Stud Threaded 3/8" x 24|Lower Coil Mounting Stud|KH, XL, XLH|
|64612-52|1952-1954|Hex Stud Threaded 5/16" x 18|Upper Coil Mounting Stud|K, KH|
|64612-55|1955-1966|Hex Stud Threaded 3/8" x 24|Upper Coil Mounting Stud|KH, XL, XLH|
===== Circuit Breaker Ignition =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1047|1952-1970|#8-36 x 1/4" Fillister Head Screw|Circuit Breaker Condenser \\ Bracket Screw|K Models, XL, XLH|
|:::|1970|:::|:::|XLCH|
|1047|1971-1978|#8-36 x 1/4" Fillister Head Screw|Circuit Breaker Point Screw|XLH, XLCH|
|1058W|1957-- |#8-32 x 5/16” Fillister Head Screw|Timer Wire Stud Screw|XLH, XLCH|
|1063W|1954-1956|#8-32 x 3/8" Fillister Head Screw|Circuit Breaker Adj Screw|KH|
|1300|1952-*|#12-24 x 1/2" Fillister Head Screw|Circuit Breaker Timer \\ to Motor Screw|K Models, XL, XLH|
|1300B|1954-1965|#12-24 x 1/2" Fillister Head Screw|Circuit Breaker Timer Screw|KH, XL, XLCH|
|2572W|1967|#6-32 Self Tapping \\ Phillips Head Screw|Circuit Breaker (74589-67) \\ Mounting Screw|XLH|
|2573W|1968-E1970|#6-32 Self Tapping \\ Phillips Head Screw|Circuit Breaker (74589-67) \\ Mounting Screw \\ (Replaced 2572W in 1968)|XLH|
|2585|1957-1970|#8-32 x 5/16" Pozidriv \\ Pan Head Screw|Timer Wire Pin Screw|XL, XLH|
|:::|1970|:::|:::|XLCH|
|2594|1965-1970|#8-32 x 1/4" Pozidriv \\ Pan Head Screw|Circuit Breaker Cover Screw|XLH|
|:::|1970|:::|:::|XLCH|
|2622|1957-1964|#8-32 x 7/16" Pozidriv \\ Pan Head Screw|Circuit Breaker Timer Adj Screw \\ (replaced 2632W)|XL, XLH|
|:::|L1972-1978|:::|Timer Adjuster Plate Screw|XL, XLCH|
|2626|1965-* |#8-32 x 1/4" Round Head Screw|Timer Cover Screw|XLH|
|2626W|1965-- |#8-32 x 1/4" Round Head Screw|Circuit Breaker Timer Cover Screw|XLH|
|2628|1971-E1972|#8-32 x 7/16" Slotted \\ Oval Head Screw|Timer Cover Screw|XLH, XLCH|
|2632|1957-1964|#8-32 x 7/6" Round Head Screw|Timer Control Wire Lock Screw|XL, XLH|
|2632W|1957-1964|#8-32 x 7/16" Round Head Screw|Circuit Breaker Timer Adj Screw \\ (replaced by 2622)|XL, XLH|
|2633|1959-1970|#8-32 x 3/8" Round Head \\ Self Tapping Screw|Circuit Breaker Cable \\ Coil Clamp Screw|XLH|
|2636W|E1972|#8-32 x 5/16" Round Head Screw|Timer Cover Screw|XLH, XLCH|
|2762|1961-1964|#10-32 x 1/2" Round Head Screw|Timer Control Coil Bracket|XLH|
|2762B|1961-1964|#10-32 x 1/2" Round Head Screw|Timer Coil Bracket Screw|XLH|
|2762W|1961-1964|#10-32 x 1/2 Round Head Screw|Timer Coil Bracket Screw|XLH|
|3422W|1966-1970|#12-24 x 5/8" Hex Head Screw|Circuit Breaker / \\ Timer Clamp Screw|XLH|
|:::|1970|:::|:::|XLCH|
|3570|1971-1979|#10-32 x 2" Hex Head Bolt|Circuit Breaker Cam \\ Center Bolt|XLH, XLCH|
|3826|1954-1964|1/4" x 28 x 1-1/4" Hex Head Bolt|Coil Bolt|KH, XL, XLH|
|:::|1973-1976|:::|Coil to Bracket Bolt|XLH, XLCH|
|3838|1965-1970 \\ 1970|1/4" x 28 x 1-5/16" Hex Head Bolt|Circuit Breaker \ \\ Coil Mounting Bolt \\ (used with Coil 31609-65 \\ and 31609-65A)|XLH \\ XLCH|
|:::|1971-1972|:::|:::|XLH, XLCH|
|4012|1957-1960|5/16" x 24 x 1-1/8" Hex Head Bolt|Timer Control Coil Bracket|XL, XLH|
|30507-47A|1952-1970|Brass Screw|Eccentric Screw, Breaker Points|K Models, XL, XLH|
|:::|1970|:::|:::|XLCH|
|32593-47|1952-1956|Screw|Timer Adjuster Screw|K Models|
|32593-57|1957-1964|Screw|Timer Adjuster Screw \\ (replaced by 2622)|XL, XLH|
|32601-78|L1972-1979|Stud|Breaker Plate / Timer \\ Adjuster Plate Screw \\ (replaced 32608-72 in '78)|XLH, XLCH|
|32608-70|1971-E1972|Stud|Breaker Plate / Timer \\ Adjuster Plate Screw|XLH, XLCH|
|32608-72|L1972-1977|Stud|Breaker Plate / Timer \\ Adjuster Plate Screw \\ (replaced by 32601-78 in '78)|XLH, XLCH|
|32669-47|1952-E1972|Screw|Breaker Point Lock Screw|K Models, XL, XLH|
|:::|1970-E1972|:::|:::|XLCH|
|32676-49|1952-1964|Stud|Circuit Breaker Wire Stud|K Models, Sportsters|
===== Magneto Ignition =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1058W|1965-- |#8-32 x 5/16” Fillister Head Screw (NC)|Magneto Control Wire Screw|XLCH|
|1074W|1965-1969|#8-32 x 7/8" Fillister Head Screw (NC)|Magneto Adapter Plate Adjuster Screw|XLCH|
|1202W|L1962-1969|#10-32 x 1/2" Fillister Head Screw|Magneto Ground Wire to \\ Insulating Block Screw \\ (Replaced Screw #29593-62 in 1967)|XLCH|
|1865W|L1962-- |#12-24 x 5/8" Countersunk Head Screw|Magneto Upper Adapter Plate Screw|XLCH|
|1867|L1962-1969|#12-24 x 15/32" Countersunk Head Screw|Magneto Adapter Plate Screw|XLCH|
|2585|1965-1969|#8-32 x 5/16" Fillister Head Screw|Magneto Control Wire Block Screw|XLCH|
|3791|1958-1969|1/4" x 28 x 3/4" Hex Head Bolt (NF)|Magneto Adapter Plate \\ to Drive Housing Screw|XLCH|
|4410|1958-1969|1/4" x 28 x 3/4" Hex Head Bolt|Magneto Adapter Plate to \\ Control Arm Bolt|XLCH|
|29531-55|1958-1969|Screw|Magneto Cover Screw|XLCH|
|29591-62|L1962-1969|Screw and Washer|Magneto Primary Ground \\ Insulating Block Screw|XLCH|
|29593-62|L1962-1966|Screw and Washer|Magneto Ground Wire to \\ Insulating Block Screw \\ (Replaced by screw #1202W in 1967)|XLCH|
|29601-48|1958-E1962|Screw|Magneto Adapter Screw|XLCH|
|29632-55|1958-1969|Screw|Magneto Condenser Mount Screw|XLCH|
|29632-62|L1962-E1966|Screw|Magneto Drive Housing Screw|XLCH|
|29632-66|L1966-1969|1/4" x 20 x 1/2" Countersunk Head Screw|Magneto Drive Housing Screw|XLCH|
|29633-55|1958-E1962|Screw and Washer|Magneto Breaker Arm Screw|XLCH|
|29633-62|L1962-1969|Screw and Washer|Magneto Breaker Arm Screw|XLCH|
|29634-55|1958-1969|Screw and Washer|Magneto Breaker Arm Contact Screw|XLCH|
|29636-55|1958-1969|Set Screw|Magneto-Coil Set Screw|XLCH|
|29637-55|1958-E1962|Screw|Magneto Drive Housing Screw|XLCH|
|29638-55|1958-E1964|Screw|Magneto - Safety Gap Plate Screw|XLCH|
|29640-55|1958-1969|Screw|Magneto Vent Cover Screw|XLCH|
|29657-62|L1962-1969|Screw|Magneto Ground Terminal Screw|XLCH|
===== Electronic Ignition =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1047|1971-1979|#8-36 x 1/4" Fillister Head Screw|Ignition Module Ground Screw \\ (electronic ign kit 32609-78) |XL, XLH, XLCH|
|1205|1982-1990|#10-24 x 3/4" Pozidriv \\ Fillister Head Screw|Ignition Module Mounting Screw|Sportsters|
|1601|1980-1990|#8-32 x 1/2" Flat Head Screw|Ignition Cover (inner) Screw|Sportsters|
|1611|1980-1985|#10-32 x 3/4" Flat Head Screw|Ignition Module Mounting Screw|XL, XLS|
|2554|1971-1979|#4-40 x 5/8" Pozidriv \\ Pan Head Screw|Ignition Sensor to Plate Screw \\ (electronic ign kit 32609-78)|XL, XLH, XLCH, XLS|
|2611A|1980-1981|#10-32 x 3/4" Pozidriv \\ Pan Head Screw|Ignition Rotor Cup Screw|XL, XLS|
|2611B|1980-1990|#10-32 x 3/4" Hex Head Screw|Ignition Rotor Cup Screw|Sportsters|
|2646|1971-1985|#8-32 x 3/4" Pozidriv \\ Pan Head Screw|Ignition Cover Screw \\ (electronic ign kit 32609-78) |XL, XLH, XLCH, XLS|
|2661W|1980-1983|#10-24 x 1/2" Self Tapping \\ Phillips Round Head Screw|Igniton Module Ground Wire Screw|XL, XLS|
|2662W|1984-1985|#10-24 x 3/8" Self Tapping \\ Phillips Round Head Screw|Igniton Module Ground Wire Screw|XL, XLS|
|2667|E1982 \\ 1982-1985 \\ L1982|5/16" x 18 x 2" Hex Head Bolt|Coil Bracket Cap Screw|XL \\ XLS, XLX \\ XLHA, XLSA|
|3570|1971-1979|#10-32 x 2" Hex Head Bolt|Nosecone Center Bolt|XL, XLCH, XLS|
|32601-70|1971-E1972|Stud|Timer Plate Stud|
|32601-78|L1976-1979|Stud|Timer Plate Stud \\ (part of Electronic Ignition Kit 32609-78)|XLH, XLCH, XLS|
|32601-80|1980-1985|Stud (#10-32 Threads)|Timer Plate Stud|XLH, XLCH, XLS|
|32608-72|L1972-E1976|Stud|Timer Plate Stud|XLH, XLCH|
===== Kick Starter =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1789|1977-1978|1/4" x 20 x 5/8" Bolt|Kicker Sprocket Cover \\ Kit (34850-77)|XLCH|
|2871W|1973-1980|5/16" x 18 x 1-1/4" Hex Head Bolt|Left Starter Hole \\ Cover Plate Bolt \\ (replaced 4022W)|XLCH|
|:::|The -78A and -78B parts books erroneously list this starter housing bolt as 2817W.||||
|3440|1968-1969|3/8" x 16 x 1/2" Hex Head Bolt|Kicker Spring Stud Hole|XLH|
|4017|1970-1980|5/16" x 18 x 1" Hex Head Bolt|Right Starter Hole Bolt|XLCH|
|4022W|1967-1972|5/16" x 18 x 1-1/8" Hex Head Bolt|Left Starter Hole Cover \\ Plate Bolt (replaced by \\ 2871W in '73)|XLH|
|:::|1970-1971|:::|:::|XLCH|
|4335W|1952-1967|3/8" x 24 x 1-1/8" Hex Head Bolt|Kickstart Pedal Bolt|K Models, Sportsters|
|4336W|1952-1976|3/8" x 24 x 1-1/8" Hex Head Bolt|Kickstart Pedal Bolt|K Models, Sportsters|
|4371W|1977-E1979 \\ 1979-1980|3/8" x 16 x 1-5/8" Socket Head Bolt|Kicker Crank Clamp Bolt|XLCH \\ XL|
|4372|1952-1967|3/8" x 24 x 1-5/8" Hex Head Bolt|Kickstart Arm Cinch Bolt|K Models, Sportsters|
|4372W|1954-1967|3/8" x 24 x 1-5/8" Hex Head Bolt|Kickstart Arm Cinch Bolt|KH, Sportsters|
|4411|1954-1976|3/8" x 24 x 1-3/4" Hex Head Bolt|Kickstart Crank Arm \\ (33061-52A) Cinch Bolt|KH, XL, XLH, XLCH|
|4720W|1971-1978|3/8" x 16 x 1-3/4" Hex Head Bolt|Kicker Sprocket Cover Bolt \\ (replaced by 4919W)|XLH, XLCH|
|4919W|(replaced by 4720W in 1976)||||
|33088-52|1952-1970|Stud|Kicker Spring Stud|K Models, Sportsters|
|33088-64|1968-1969|3/8" x 16 x 7/16" Hex Head Bolt|Kicker Spring Stud Hole|XLH|
|33088-71|1971-E1979|Stud|Kick Starter Spring Stud|XLCH|
|33088-79|E1979 \\ 1979-1980|Stud|Kicker Spring Stud|XLCH \\ XL, XLS|
|33356-52|1952-E1979 \\ 1979-1980|Stud|Kicker Crank Gear Stop|K Models, XLCH \\ XL|
|59146-52|1967-1980|5/16" x 24 x 3/4" Hex Head Bolt|Crankcase Kickstarter \\ Shaft Plug Bolt|XL, XLH, XLS|
===== Electric Starter / Relay =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|910|1981-1990|M4 x 0.7 x 10mm \\ Phillips Head Screw w/ Washer|Starter End Cover Screw|Sportsters|
|917|1981-1990|M6 x 42 mm Phillips Head Screw|Starter Housing Screw|Sportsters|
|2682|1967-1973 \\ 1975-1980|#10-32 x 3/8" Phillips Head Screw|Prestolite Starter End \\ Cover (center) Bolt|XL, XLH, XLS|
|:::|1974-E1976|:::|(Hitachi Starter End Cover \\ Kit 31565-67)|XLH|
|2765W|1967-E1968|1/4" x 20 x 5/8" Round Head Screw|Starter Relay Kit (71449-67) \\ Relay Mounting Screw|XLH|
|2871W|1967-1980 \\ 1970-1979|5/16" x 18 x 1-1/4" Hex Head Bolt|Left Starter Hole Cover \\ Plate Bolt \\ (replaced bolt 4022W)|XLH \\ XLCH|
|:::|The -78A and -78B parts books erroneously list this starter housing bolt as 2817W.||||
|2773|1973-1978|1/4" x 20 x 1/2" Pozidriv Head Screw|Starter Relay Mounting Bolt|XLH|
|2374|1967-E1968 \\ L1971-1974|1/4" x 20 x 5/8" Pozidriv \\ Pan Head Screw|Starter relay Mounting Bolt|XLH \\ XLH|
|3401|1981-1985|Bolt w/ Washer|Starter Frame Bolt|XL, XLS|
|3802W|1967-1980|1/4" x 20 x 7/8" Hex Head Bolt|Solenoid Mounting Bolt|XL, XLH, XLS|
|4005W|1967-- |5/16" x 18 x 1" Hex Head Bolt|Starter Motor Clamp Bolt|XLH|
|4017|1967-1978|5/16" x 18 x 1" Hex Head Bolt|Starter Motor Clamp Bolt|XL, XLH, XLS|
|4017|1967-1980 \\ 1970-1980|5/16" x 18 x 1" Hex Head Bolt|Right Starter \\ Shaft Housing Bolt|XL, XLH, XLS \\ XLCH|
|4022W|1967-1972|5/16" x 18 x 1-1/8" Hex Head Bolt|Left Starter Hole \\ Cover Plate Bolt \\ (replaced by 2871W in '73)|XLH|
|:::|1970-1971|:::|:::|XLCH|
|29632-66|1967-E1968|:::|Starter Relay Kit (71449-67) \\ Relay Bracket Screw|XLH|
|31478-67|1967-1980|Shouldered Bolt|Starter Gear Shift \\ Lever Pivot Bolt|XL, XLH, XLS|
|31535-66|1967-1980|Bolt|Starter Thru Bolt|XL, XLH, XLS|
|31576-73|1974-E1976|Bolt|Hitachi Starter Thru Bolt|XLH|
|31585-73|1974-E1976|Screw with Washer|Hitachi Starter \\ End Cover Screw|XLH|
|45995-73|1981-1990|Screw|Starter Mounting Screw (short)|Sportsters|
|45999-81|1981-1985|Screw|Starter Mounting Screw (long)|XL, XLS|
====== Clutch ======
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|2613|1954-1970|#10-24 x 1/4" \\ Pozidriv Pan Head Screw|Clutch Cover Screw|KH, Sportsters|
|2660|1952-E1953|#10-24 x 1/4" \\ Round Head Screw (NC)|Clutch Sprocket Cover Screw|K, KK|
|3583|Bolt|L1984-1985|Clutch Ramp Lockplate Bolt|XL, XLS, XLX|
|11735|L1984-1985|Screw|Clutch Adjustment Screw|XL, XLS, XLX|
|37584-52|1952-1953|Stud|Clutch Hub Stud|K|
|37584-54|1954-1963|Stud|Clutch Hub Stud|KH, Sportsters|
|37584-64|1964-1966|Stud|Clutch Hub Stud|XLH, XLCH|
|37584-67|1967-1970|Stud|Clutch Hub Stud|XLH|
|38008-72|L1972-E1974|Stud|Clutch Releasing Disc Stud|XLH, XLCH|
|38130-54|1952-1970|Screw|Clutch Adjusting Screw|K Models, Sportsters|
|38130-71|1971-E1984|Screw|Clutch Adjusting Screw|Sportsters|
====== Transmission ======
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|857|L1984-1990|#10-24 x 3/8" Knurled \\ Socket Head Screw|Trans Sprocket Screw|Sportsters|
|901|1979|1/4" x 20 x 2-1/2" Pozidriv \\ Fillister Head Screw|Trans Sprocket Cover Screw|XLS|
|902|1979|1/4" x 20 x 1" Pozidriv Oval \\ Countersunk Head Screw|Trans Sprocket Cover Screw|XLS|
|913|1979|1/4" x 20 x 1-1/2" Pozidriv \\ Fillister Head Screw|Trans Sprocket Cover Screw|XLS|
|1305|1979|1/4" x 20 x 1" Pozidriv \\ Fillister Head Screw|Trans Sprocket Cover Screw|XL, XLS|
|1308|L1977-1978|1/4" x 20 x 1-3/4" Pozidriv \\ Fillister Head Screw|Lower Sprocket Cover Bolt|XL, XLCH|
|1381|1979-1980|1/4" x 20 x 2-1/2" Pozidriv \\ Fillister Head Screw|Trans Sprocket Cover Screw|XL, XLCH, XLS|
|1608|1961-1971|#6-32 x 7/16" Countersunk \\ Flat Head Pozidriv Screw|Shift Pawl Retainer Screw|XLH, XLCH|
|1658A|1961-- |#6-32 x 7/16" Countersunk Head Screw|Pawl Carrier Screw|XLH, XLCH|
|1797R|1981-1990|1/4" x 20 x 2" Hex \\ Socket Head Screw|Sprocket Cover Screw|Sportsters|
|2346W|1979-1980|1/4" x 20 x 1-1/2" Pozidriv \\ Fillister Head Screw|Sprocket Cover Screw|XL, XLCH, XLS|
|2351W|1980-1985|1/4" x 20 x 2" Pozidriv \\ Fillister Head Screw|Trans Sprocket Cover Screw|XL, XLS|
|2551W|1977-1990|1/2" x 20 x 1" Hex Head Bolt|Shift Lever Cinch Bolt|Sportsters|
|2660|1961-E1984|#10-24 x 3/8 Pozidriv \\ Pan Head Screw|Mainshaft Oil Seal Retainer|XLH, XLCH|
|2660|1961-1978|#10-24 x 3/8" Pozidriv \\ Pan Head Screw|Trans Sprocket Shaft \\ Seal Plate Screw|XLH, XLCH|
|2660|1979-1981|#10-24 x 3/8" Pozidriv \\ Pan Head Screw|Trans Sprocket Cover Screw|XL, XLCH, XLS|
|2669|1961- |#10-24 x 3/8" Round Head Screw|Trans Mainshaft Screw|Sportsters|
|:::|1961- |:::|Transmission Mainshaft Oil Seal \\ Retainer Screw|Sportsters|
|2669W|1961-- |#10-24 x 3/8" Round Head Screw|Mainshaft Oil Seal Retainer Screw|XLH, XLCH|
|2672|1952-1960|#10-24 x 1/2" Round Head Screw|Transmission Mainshaft \\ Oil Seal Ret Screw|K Models, Sportsters|
|2672B|1954-1960|#10-24 x 1/2" Round Head Screw|Mainshaft Oil Seal Retainer Screw|KH, Sportsters|
|2871|L1972-1974|5/16" x 18 x 1-1/4" Hex Head Bolt|Shift Lever Cinch Bolt|XLH, XLCH|
|2879W|1979-1985|3/8" x 16 x 1" Hex Head Bolt|Upper Rear Case Plug Bolt \\ (over tranny)|XL, XLS, XLX|
|3419|1980-1985|5/16" x 18 x 2-1/4" Hex Head Bolt|Sprocket Cover Bolt|XL, XLS|
|3440|1979-1980|3/8" x 16 x 1/2" Hex Head Bolt|Upper Rear Case Plug Bolt \\ (over tranny)|XL, XLCH, XLS|
|3478|1981-1990|1/4" x 20 x 2-1/2" Hex Socket Head Bolt|Sprocket Cover Bolt|Sportsters|
|3481|1981-1985|1/4" x 20 x 2-1/4" Hex Socket Head Bolt|Primary Cover Screw|XL, XLS|
|3854|L1984-1985|7/16" x 14 x 1" Hex Head Bolt|Pawl Carrier Support Shim Bolt|XL, XLS, XLX|
|3991|1957-1985|5/16" x 18 x 7/8" Hex Head Bolt \\ (NC, grade 5, zinc)|Trans Trapdoor Bolts|XL, XLH, XLCH|
|:::|1957- |5/16" x 24 x 7/8" Hex Head Bolt (NF) ((1955-1965 Sportster and KH Model Parts Catalog pg 9))|:::|:::|
|:::|Thread pitch discrepancy between the -59 and -65 parts catalogs. \\ Corrected to 5/16" x 18 x 7/8" Hex Head Bolt in 1966 supplement catalog (99451-66)||||
|3991|1979-1981|5/16" x 24 x 7/8" Hex Head Bolt|Upper Front Engine Mount to \\ Frame Bracket Bolt|XL, XLCH XLS|
|4014W|1964-E1972|5/16" x 24 x 1-1/4" Hex Head Bolt|Shift Lever Cinch Bolt|XLH, XLCH|
|4621|1954-E1984|7/16" x 14 x 1-1/8" Hex Head Bolt|Pawl Carrier Support Shim Bolt|KH, Sportsters|
|4720W|1971-1976|3/8" x 16 x 1-3/4" Hex Head Bolt|Sprocket Cover Bolt|XLH, XLCH|
|34065-52|1952-1985|Screw|Shifter Cam Follower Ret Screw|K Models, Sportsters|
|34880-77 \\ 34880-77A|1980-1982 \\ 1982|Female Hex Stud (both ends)|Trans Sprocket Cover \\ Mounting Stud|XL, XLS|
|34880-77B|1982-1985|Hex Stud Kit \\ (includes male threaded stud)|Trans Sprocket Cover \\ Mounting Stud|XL, XLS, XLX|
|34886-82|1982-1985|Hex Stud \\ (female threads both ends)|Trans Sprocket Cover \\ Mounting Stud|XL, XLS, XLX|
|34890-52|1952-1970|Bolt|Sprocket Cover Bolt|K Models, Sportsters|
|34891-52|1958-1961|Bolt|Sprocket Cover Screw (lower)|XLH, XLCH|
|34895-79|1979|Dual Female Hex Ended Stud|Lower Sprocket Cover \\ Mounting Stud|XL, XLCH, XLS|
|42450-80|1980-1990|1/2" x 13 x 2" Hex Head Bolt|Sprocket Cover Bolt|Sportsters|
====== Suspension ======
\\
===== Front Forks / Triple Tree =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}||||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|Pic(s)|
|854|1983-1985 \\ L1983-1984 \\ 1986-1987|3/8" x 24 x 1-1/2" Knurled \\ Socket Head Screw|Lower Fork Bracket \\ to Slider Pinch Screw|XLX \\ XR-1000 \\ 883, Hugger|
|1435W|1967-1969|1/4" x 20 x 3/8" Phillips Head Screw|Fork Cable Guide Screw|XLH|
|2625|1954-1970|#8-32 x 5/8" Pozidriv \\ Pan Head Screw|Fork Boot Mounting Screw|KH, XL, XLH, XLCH|
|2635|1953-1954|#8-32 x 1/2" Round Head Screw|Fork Front Panel Screws|K, KH|
|2638|1954-* |#8-32 x 5/8" Round Head Screw|Fork Boot Mounting Screw \\ (Replaced by #2638W)|KH, Sportsters|
|2638W|1954-- |#8-32 x 5/8" Round Head Screw|Fork Boot Mounting Screw|KH, Sportsters|
|2758|1952-1970|1/4" x 20 x 1/2" Recessed \\ Truss Head Screw (NC)|Fork Panel Mounting Screw|K Models, Sportsters|
|2823|1952-1970 \\ 1964-1970|5/16" x 18 x 3/8" Recessed \\ Truss Head Screw (NC)|Fork Panel Mounting Screws|K Models, XL, XLH \\ XLCH|
|2823|1954-1970 \\ 1964-1970|5/16" x 24 x 3/8" Phillips Head Screw|Fork Bracket End Screw|KH, XL, XLH \\ XLCH|
|:::|1973-1985|:::|Lower Fork Bracket \\ Cover Screw|XLH, XLCH, XLS|
|2823|1971-1987|5/16" x 18 x 3/8" Phillips Head Screw|Fork Bracket End Screw|Sportsters, XLH 1100|
|2631|1953-1958|#8-32 x 5/16" Round Head Screw|Fork Front Panel Screws|K Models, Sportsters|
|4370|1952-E1954|3/8" x 24 x 1-9/16" Hex Head Bolt|Upper Tree Bolt|K, KH|
|:::|1967- |:::|:::|XLH|
|4370HB|1967-1970|3/8" x 24 x 1-9/16" Hex Head Bolt|Lower Fork Tree \\ Front Screw \\ (replaced by 4374B)|XLH|
|4371B|1962- |3/8" x 24 x 1-5/8" Socket Head Screw|Upper Tree Cinch Bolt|XLH, XLCH|
|4371B|1962- |3/8" x 16 x 1-5/8" Socket Head Bolt|Upper Tree Cinch Bolt \\ (replaced by 4371W)|XLH, XLCH|
|:::|Parts Books discrepancy - Same part no. with course threads. Retrofit to 1962-up tree replacements.||||
|4371W|1962-1987|3/8" x 16 x 1-5/8" Socket Head Bolt|Upper Tree Cinch Bolt \\ (replaced 4371B)|Sportsters|
|4372W|1952-1966|3/8" x 24 x 1-5/8" Hex Head Bolt \\ (Cadmium)|Upper Tree-Tube \\ Cinch Bolt|K Models, XL, XLH|
|4374B|1971-1972|3/8" x 24 x 1-5/8" Hex Head Bolt|Fork Slider Bolt|XLH, XLCH|
|4379|1952-1964|3/8" x 24 x 1-23/32" Hex Head Bolt|Steering Damper \\ Anchor Plate Bolt|K Models, Sportsters|
|:::|1965-1966|:::|:::|XLCH|
|4379HB|1954-1964|3/8" x 24 x 1-23/32" Hex Head Bolt|Steering Damper \\ Anchor Plate Bolt \\ (replaced 4379) \\ (replaced by 4411)|KH, Sportsters|
|4411|1954-1964 \\ 1965-1966 \\ 1973-1983|3/8" x 24 x 1-3/4" Hex Head Bolt|Lower Tree Slider Cinch Bolt \\ (replaced 4379HB)|KH, XL, XLH, XLCH \\ XLCH \\ XLH, XLCH, XLS|
|4660W|1968-? |7/16" x 20 x 1-1/2" Hex Head Bolt|Damper Tube Bolt|XLH, XLCH|
|4724|1984-1985|3/8" x 24 x 1-1/2" Hex Head Bolt|Lower Tree Slider Cinch Bolt|XL, XLS, XLX|
|4726|1968-1972|7/16" x 20 x 1-1/2" Hex Head Bolt|Fork Damper Tube Bolt|XLH, XLCH|
|45405-75|1975-1984|Screw|Fork Damper Tube Screw|XLH, XLCH, XLS|
|45405-75A|1975-1990|Screw|Fork Damper Tube Screw \\ and Copper Washer|Sportsters|
|45782-62|1962-1977|Helicoil|Fork Bracket Screw Insert \\ (replaced by 45782-72)|XLH, XLCH|
|45782-72|1962-1977|Helicoil|Fork Bracket Screw Insert|XLH, XLCH|
|45782-72A|1962-1987|Helicoil|Fork Bracket Screw Insert|Sportsters|
|45790-80|1979-1994|M4 X 0.70mm x 6mm \\ JIS Head Screw w/ Washer|Fork Drain Screw|Sportsters|{{ :techtalk:ref:tools:1979-2003_sportster_fork_drain_screw_by_robison_motorcycles.jpg?linkonly |Pic1}} ((photo courtesy of Ebay seller, Robison Motorcycles [[ https://www.ebay.com/str/robisonmotorcycles?_trksid=p2047675.l2563 |Link to Ebay Store]] ))|
|:::|1995-1997 \\ 2000-2003|:::|:::|STD, DLX, HUG \\ 1200, 883C, 1200C|:::|
|45995-73|1973-1974|Screw|Fork Damper Tube Screw|XLH, XLCH|
|45998-73|1973-1974 \\ 1979-1987|Stud|Slider Clamp Stud|Sportsters|
|46020-57|1957-1970|Screw|Boot Vent Screw|Sportsters|
|46743-52|1952-1964|Screw|Steering Damper Bushing Screw|K Models, Sportsters|
|:::|1965-1966|:::|:::|XLCH|
===== Swingarm =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1198|L1972-1981|#10-24 x 1/2" Pozidriv \\ Fillister Head Screw|Swingarm Bearing Lockwasher Screw|XLH, XLCH, XLS|
|2657|1952- |#10-3/8" Self Tapping \\ Hex Head Screw|Rear Fork Bearing \\ Locknut Washer Screw|K Models, Sportsters|
|41568-81|1982-1985|Bolt|Swingarm Pivot Bolt|XL, XLS|
|41570-77|1982-1990|Special Fastener \\ 5/16" x 24 Threads|Rear Axle Adjuster Bolt|Sportsters|
|47511-52|1952-1981|Pivot Bolt|Swingarm Pivot Bolt|K Models, Sportsters|
|Included with Frame Adapter Kit (43785-75) to adapt frame (47014-73) to earlier models; 1967-1972 XLH, 1970-1972 XLCH|||||
| |2882W|5/16 x 18 x 5/8" Hex Head Bolt|||
| |3204W|1/4" x 20 x 5/8" Self Tapping Slotted Head Screw \\ (w/ ext. tooth LW)|||
| |3738|1/4" x 20 x 5/8" Hex Head Bolt|||
| |3953W|5/16" x 24 x 1/2" Hex Head Bolt|||
===== Shocks =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|991|1954-1964|#10-24 x 1" Pozidriv \\ Fillister Head Screw|Shock Cover Clamp Screw|KH, XL, XLH|
|1214|1952-1964|#10-24 x 3/4" Fillister Head Screw|Shock Cover Clamp Screw|K Models, Sportsters|
|1214HW|1954-1964|#10-24 x 3/4" \\ Fillister Head Screw|Shock Cover Clamp Screw|KH, XL, XLH|
|3820|1982-1985|1/2" x 13 x 2-1/4" Hex \\ Socket Head Bolt|Upper Shock Mounting Bolt|XL, XLS|
|4081|1982-1985|3/8" x 24 x 1-3/4" Hex Head Bolt|Lower Shock Mounting Bolt|XL, XLS|
|4411|1979-1981|3/8" x 24 x 1-3/4" Hex Head Bolt|Upper Shock Mounting Bolt|XL, XLCH, XLS|
|54515-52|1953-1955|Stud|Upper Shock Mounting Stud|K, KH|
|54515-56|1956-1966|Stud|Upper Shock Mounting Stud|K Models, Sportsters|
|54515-56A|1955-1966|Stud|Upper Shock Mounting Stud|KH, XL, XLH, XLCH|
|54515-56B|1967-1974|Stud|Upper Shock Mounting Stud|XLH, XLCH|
|:::|1956-?|:::|:::|KH, Sportsters|
|54515-57|1957-1964|Stud|Upper Shock Mounting Stud \\ Mounts Rear Safety Guard|K Models, Sportsters|
|54515-75|1975-1978|Stud|Upper Shock Mounting Stud|XLH, XLCH|
|54516-52|1953-1955|Stud|Lower Shock Mounting Stud|K, KH|
|54516-56|1956-1966|Stud|Lower Shock Mounting Stud|K Models, Sportsters|
|54516-56A|1967-- |Stud|Lower Shock Mounting Stud|XLH, XLCH|
|:::|1956-?|:::|:::|KH, Sportsters|
|54516-56B|1956-1974|Stud|Upper Shock Mounting Stud|KH, XL, XLH, XLCH|
|54516-72|1956-1974|Lower Shock Mounting Stud|KH, XL, XLH, XLCH|
|54516-75|1975-1978|Stud|Lower Shock Mounting Stud|XLH, XLCH|
====== Wheels ======
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1440W|1967-1969|#10 x 3/8" Self Tapping \\ Round Head Screw|Rear Aluminum Rim Screw|XLCH|
|:::|1967-1972|:::|:::|XLH (low clearance)|
|1445W|E1967-1969|#10 x 3/4" Self \\ Tapping Roung Head Screw|Rear Wheel Steel Rim Screw|XLH, XLCH|
|2731W|1975- |#10 x 3/8" Self Tapping \\ Phillips Head Screw|Rear Brake Cable Clamp Screw|XLH, XLCH|
|2818|1954-1978|5/16" x 18 x 1-1/2" Hex Head Bolt|7 Spoke Cast Rear Wheel \\ Right Bearing Housing Bolt \\ (1978 for retrofit)|KH, XL, XLCH|
|3655|1984-1990|5/16" x 18 x 7/8" Pan Head Screw|Front Brake Disc \\ to Wheel Screw|Sportsters|
|3680|1978-E1981|5/16" x 18 x 7/8" Countersunk Socket \\ Flat Head Screw (chrome)|Front Brake Disc \\ to Wheel Screw \\ (9 spoke cast wheel) \\ ('73-'77 steel wheel hub)|XL, XLCH, XLS|
|3685|1974-1977|5/16" x 18 x 1" Socket Head Screw|Front Brake Disc to \\ Wheel Adapter Screw|XLH, XLCH|
|3769|1979-E1983|7/16" x 14 x 1-1/2" Hex Head Bolt|Cast Rear Wheel \\ Sprocket Mounting Bolt \\ (replaced by 3771 in '85)|XL, XLCH, XLS|
|3771|L1983-1990|7/16" x 14 x 1-1/2" Hex Head Bolt|Cast Rear Wheel \\ Sprocket Mounting Bolt|Sportsters|
|3780|1954-1978|5/16" x 18 x 1-1/2" Countersunk \\ Socket Flat Head Screw|7 Spoke Cast Rear Wheel \\ Left Bearing Housing Screw \\ (1978 for retrofit)|XL, XLCH|
|3781A|1974-1978|5/16" x 18 x 1-1/4" Countersunk \\ Socket Flat Head Screw|Front Brake Disc \\ to Wheel Screw \\ ( for bearing housing adapters)|XL, XLCH|
|3782|1981-1990|7/16" x 14 x 1-1/4" Hex Head Bolt|Steel Rear Wheel \\ Sprocket Mounting Bolt|Sportsters|
|3793|1978|1/4" x 20 x 5/8" Countersunk Socket \\ Flat Head Screw|Front Brake Disc \\ to Wheel Screw|XL, XLCH|
|3795|L1981-1983|5/16" x 18 x 7/8" \\ Flat Socket Head Screw|Front Brake Disc to Wheel Screw|XL, XLS|
|3854|1979-1980|7/16" x 14 x 1" Hex Head Bolt|Steel Rear Wheel \\ Sprocket Mounting Bolt|XL, XLS|
|3970B|1954-1978|5/16" x 24 x 1" Hex Head Bolt|Brake Drum to Hub Bolt|KH, XL, XLH, XLCH|
|4017|1954-1978|5/16" x 18 x 1" Hex Head Bolt|9 Spoke Cast Rear Wheel \\ Right Bearing Housing Bolt \\ (1978 for retrofit)|KH, XL, XLCH|
|4391|1978-1981|5/16" x 24 x 5/8" Hex Head Bolt|Front Brake Hose \\ Tee Mounting Bolt|XL, XLCH, XLS|
|:::|1982|:::|:::|XLS|
|39985-52|1952-1978|Welded Eyelet Bolt|Rear Chain Adjuster|K Models, XL, XLH, XLCH|
|41191-74|1974-1977|1/4" x 20 x 5/8" Socket \\ Flat Head Screw|Front Brake Disc \\ to Wheel Screw|XL, XLCH|
|41551-52|1952-1978|Axle Bolt|Rear Wheel Axle|K Models, Sportsters|
|41563-77|1979-1988|Axle Bolt|Rear Wheel Axle|Sportsters|
|43024-64|1964-1969|19" Spoke (short)|Front Wheel Spoke|XLCH|
|:::|1967-1969|:::|:::|XLH|
|43024-70|1970-1972|19" Spoke (short)|Front Wheel Spoke|XLH, XLCH|
|43024-73|1973-1977|19" Spoke (short)|Front Wheel Spoke|XLH, XLCH|
|43024-73A|1973-1985|19" Metric Spoke Set (short)|Front Wheel Spoke Set|XLH, XLCH, XLS|
|43025-64|1964-1969|19" Spoke (long)|Front Wheel Spoke|XLCH|
|43025-70|1970-1972|19" Spoke (long)|Front Wheel Spoke|XLH, XLCH|
|43025-73|1973-1977|19" Spoke (long)|Front Wheel Spoke|XLH, XLCH|
|43025-73A|1973-1985|19" Metric Spoke Set (long)|Front Wheel Spoke Set|XLH, XLCH, XLS|
|43027-52|1952-1955|6-1/8" Spoke (short)|19" Front Wheel Spoke|K Models|
|43027-52|1954-1955|6" Spoke (short)|19" Front Wheel Spoke|KH|
|:::|1958-1963|:::|:::|XLCH|
|43027-53|1952-1963|Spoke (short)|18" Front Wheel Spoke|K Models, XL, XLH|
|43027-64|1964-1972|Spoke (short)|18" Front Wheel Spoke|XLH|
|43028-52|1952-1955|8-1/2" Spoke|19" Front Wheel Spoke|K Models|
|43028-52|1954-1955|8-3/8" Spoke|19" Front Wheel Spoke|KH|
|:::|1958-1963|:::|:::|XLCH|
|43028-64|1964-1972|Spoke (long)|18" Front Wheel Spoke|XLH|
|43031-36|1955-1972|Spoke, low road clearance|Rear Wheel Spoke|KH, XL, XLH, XLCH|
|43031-70|1970-1978|Spoke|Rear Wheel Spoke|XLH, XLCH|
|43031-70A|1970-1978|Spoke and Nipple Set (metric)|Rear Wheel Spoke|XLH, XLCH|
|43032-40A|1979-1985|Spoke and Nipple Set|16" Rear Wheel Spoke|XL|
|43099-29|1955-1978|Spoke / Nipple Set|Rear Wheel Spokes|KH, Sportsters|
|:::|1964-1972|:::|Front Wheel Spoke Nipple|XLH, XLCH|
|:::|1955-1978|Spoke and Nipple Set (1978)|Rear Wheel Spokes|:::|
|43100-47A|1952-1963|Spoke Nipple|Front Wheel Spoke Nipple|K Models, Sportsters|
|43567-79|1979-1990|3/8" x 16 x 15/64" Hex Socket \\ Countersunk Flat Head Screw|Brake Disc to Hub Screw|Sportsters|
|43871-52|1952-1972|Axle Bolt|Front Wheel Axle|K Models, Sportsters|
|43871-73|1973-1977|Axle Bolt|Front Wheel Axle|XLH, XLCH|
|43883-77|1978-1983|Axle Bolt|Front Wheel Axle|XL, XLCH|
|43883-84|1984-1987|Axle Bolt|Front Wheel Axle|Sportsters|
====== Brakes ======
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|853|1982-1990|5/16" x 24 x 2-1/4" Hex Head Bolt|Rear Master Cylinder \\ Mounting Bolt|Sportsters|
|856|L1983|5/16" x 24 x 1" Knurled \\ Socket Head Screw|Front Brake Distribution \\ Disc Mounting Screw|XL, XLS, XLX|
|860|1984-1985 \\ L1983-1984|3/8" x 16 x 2" Knurled \\ Socket Head Bolt|Front Caliper Mounting Bolt|XL, XLS, XLX \\ XR-1000|
|2330|L1983-1984|1/2" Long Screw|Right Master Cylinder \\ Cover Screw|XR-1000|
|2331|L1983-1984|3/8" Long Screw|Left Master Cylinder \\ Cover Screw|XR-1000|
|2401|1982- |#10-24 x 5/8" Pozidriv \\ Oval Countersunk Screw|Front Master Cylinder \\ Cover Screw|XL, XLS|
|2501|1980-1990|#8-32 x 3/8" x 9/16" \\ Self Tapping Screw|Rear Brake Line Clip Screw|Sportsters|
|2579|1982-1990|#8-32 x 5/8" Pozidriv \\ Oval Countersunk Head \\ Screw (grade 2)|Front Master Cylinder \\ Cover Screw|Sportsters|
|2628|1973-1981|#8-32 x 7/16" Countersunk Head Screw|Front Master Cylinder \\ Cover Screw|XLH, XLCH, XLS|
|2660|1961-1972|#10-24 x 3/8 Pozidriv \\ Pan Head Screw|Front Brake Cable \\ Tube Clamp Screw|XLH, XLCH, XLS|
|2664|1973-1977 \\ 1981- |#10-24 x 7/16" Pozidriv \\ Pan Head Screw|Brake Hose Clip Screw|XLH, XLCH|
|2661W|1975-1976|#10-24 x 1/2" Self Tapping \\ Phillips Head Screw|Rear Brake Cable \\ Clamp Screw|XLH, XLCH|
|:::|L1981-1983|:::|Brake Line Mounting \\ Bracket Screw (F-R)|XL, XLS|
|2662W|1984-1985|#10-24 x 3/8" Self Tapping \\ Phillips Head Screw|Brake Line \\ Mounting Bracket Screw (F-R)|XL, XLS, XLX|
|2669W|1961-1976|#10-24 x 3/8 Round Head Screw|Brake Cable Tube Clamp \\ Screw (replaced by 2674W)|XL, XLH, XLCH|
|2672B|1961-1976|#10-24 x 1/2" Round Head Screw|Brake Cable Clamp Screw \\ (replaced by 2691W)|XLH, XLCH|
|2674W|1961-1972|#10-24 x 3/8 Phillips Head Screw|Brake Cable Tube Clamp \\ Screw (replaced 2669W)|XL, XLH, XLCH|
|2691W|1961-1976|#10-24 x 1/2" Phillips Head Screw|Brake Cable Clamp Screw \\ (replaced 2672B)|XLH, XLCH|
|2706|L1977-1978|#10-24 x 1" Socket Head Screw|Rear Brake Cable \\ Clamp Screw|XLH, XLCH|
|2706|1979|#10-24 x 1" Socket Head Screw|Brake Pedal Cinch Screw|XL, XLCH, XLS|
|2825W|E1977|1/4" x 20 x 1" Socket Head \\ Screw (grade 1)|Rear Brake Adjusting Screw|XL, XLCH|
|2887W|1975-1976|5/16" x 18 x 1-3/4" Hex Head Bolt|Brake Pedal Arm \\ Cinch Bolt|XLH, XLCH|
|3251|1975-1976|1/4" x 20 x 1-3/4" Threaded Stud|Rear Brake Adjusting Screw|XLH, XLCH|
|3254|1975-1976|1/4" x 20 Stud|Brake Stop Stud|XLH, XLCH|
|3419|1979-1981|5/16" x 18 x 2-1/4" Hex Head Bolt|Rear Master Cylinder \\ Mounting Bolt|XL, XLCH, XLS|
|3424|1979|5/16" x 18 x 2-1/4" \\ Hex Head Bolt (black)|Rear Master Cylinder \\ Mounting Bolt|XLS|
|3433|1964-1972|7/16" x 20 x 2-3/4" Hex Head Bolt|Front Drum Brake \\ Pivot Stud Bolt|XLH, XLCH|
|3444|1982-1985|1/4" x 20 x 5/8" Socket \\ Fillister Head Screw|Front Master Cylinder \\ Handlebar Clamp Screw|XL, XLS|
|:::|1983-1990|:::|Brake Line Clamp Screw|Sportsters|
|3453|1974-1977|5/16" x 24 x 2-1/4" Hex \\ Socket Head Screw|Front Brake Caliper \\ Mounting Bolt|XLH, XLCH|
|3517|1984-1990|#10-32 x 1/2" Hex Screw|Brake Disc \\ Retaining Pad Screw|Sportsters|
|3728|E1979|1/4" x 20 x 1/2" Hex Head Bolt|Rear Brake \\ Tee Bracket Bolt|XLCH|
|3780|1954-1978|5/16" x 18 x 1-1/2" Countersunk \\ Socket Flat Head Bolt|7 Spoke Cast Rear Wheel \\ Left Bearing Housing Bolt \\ (1978 for retrofit)|KH, XL, XLCH|
|3802W|1979|1/4" x 20 x 7/8" Hex Head Bolt|Brake Hose Bracket Screw|XL, XLCH, XLS|
|3825|1954-1974|1/4" x 28 x 1" Hex Head Bolt|Rear Brake Cross Shaft \\ Adj Bolt (replaced #3840 in '75)|KH, XLH, XLCH|
|3826|1975-1978|1/4" x 28 x 1-1/4" Hex Head Bolt|Foot Peg Bolt|XLH, XLCH|
|3840|1952-1974|1/4" x 28 x 1-1/4" Hex Head Bolt|Rear Brake Cross Shaft Adj Bolt \\ (replaced by #3825 in '75)|K Models, Sportsters|
|3970B|1966-1978|5/16" x 24 x 1" Hex Head Bolt|Rear Brake Hub Mounting Bolt \\ (replaced 3971 in '66)|XLH, XLCH|
|3971|1952-1965|5/16" x 24 x 3/4" Hex Head Bolt (NF)|Brake Shell / Sprocket Bolt \\ (replaced by 3970B in '66)|K Models, Sportsters|
|3993|E1980|1/4" x 20 x 1-1/4" Hex Head Bolt|Brake Pedal Stop Bolt|XL, XLS|
|4015|1984-1990|1/4" x 20 x 7/8" \\ Socket Round Head Screw|Front Master Cylinder \\ Handlebar Clamp Screw|Sportsters|
|4020|1952- |5/16" x 24 x 1-3/8" Hex Head Bolt (NF)|Rear Brake Lever Bolt|K Models, Sportsters|
|4020W|1954- |:::|Rear Brake Lever Bolt|K Models, Sportsters|
|4036|1954-1974|5/16" x 24 x 1-1/2" Hex Head Bolt|Cross over Brake Arm Cinch Bolt|KH, XL, XLH, XLCH|
|4092|1982-1985|5/16" x 18 x 3/4" Screw|Rear Brake Tee Mounting Bolt|XL, XLS|
|4387|E1983|5/16" x 24 x 27/32" Hex Socket Button \\ Head Screw (grade 5)|Front Brake Distribution \\ Disc Mounting Screw|XL, XLS|
|4391|1978-1982|5/16" x 24 x 5/8" Hex Head Bolt|Front Brake Tee Bolt|XL, XLCH, XLS|
|45067-83|L1983-1984|Screw|Spacer Screw|XR-1000|
|4680|1952-1963|7/16" x 20 x 2-1/8" Hex Head Bolt|Front Brake Pivot Stud Bolt|K Models, Sportsters|
|4681W|1964-- |7/16" x 20 x 2-3/4" Hex Head Bolt|Front Brake Pivot Stud Bolt|XLH, XLCH
|4701|1977-1978|5/16" x 24 x 1-1/2" Hex Head Bolt|Brake Pedal Arm Cinch Bolt|XL, XLCH|
|:::|L1979|:::|Brake Pedal Shaft Bolt|XL, XLCH, XLS|
|4724|1974-1977|3/8" x 24 x 1-1/2" Hex Head Bolt|Front Brake Caliper \\ Anchor Arm Bolt|XLH, XLCH|
|41191-74|1974-1977|1/4" x 20 x 5/8" Countersunk \\ Socket Flat Head Screw|Front Brake Disc \\ Mounting Bolt|XLH, XLCH|
|41198-73|1973|3/8" x 16 x 1" Hex \\ Head Bolt (thin head)|Front Brake Disc \\ to Hub Bolt|XLH, XLCH|
|41739-84|1984-E1990|7/16" x 24 ((https://www.denniskirk.com/v-twin-manufacturing/chrome-12mm-banjo-bolt-kit-23-0614.p276271.prd/276271.sku)) Hex Head Bolt (holed)|Front Brake Hose to \\ Master Cylinder Banjo Bolt|XL, XLS, XLX|
|:::|1984-1985|:::|(F) Brake Caliper Banjo Bolt|
|41747-82|1982-E1984|9/16" x 24 \\ Socket Head Bolt (holed)|Front Brake Hose to \\ Master Cylinder Banjo Bolt|XL, XLS|
|41747-82A|L1984-1990|3/8" x 24 \\ Socket Head Bolt (holed)|Front Brake Hose to \\ Master Cylinder Banjo Bolt|Sportsters|
|41749-58|1973-1977|1/4"-28 Bleeder Screw|(F-R) Brake Bleeder Screw|Sportsters|
|41876-52|1952-1953|Stud|Brake Shoe Pivot Stud|K|
|41876-54|1954-1972|Stud|Brake Shoe Pivot Stud|KH, Sportsters|
|41876-73|1973-1978|Stud|Brake Shoe Pivot Stud|XLH, XLCH|
|41882-73 \\ 41882-73A|1973-1978|7/16" x 20 x 1-1/2" Hex Head Bolt|Pivot Stud Bolt|XLH, XLCH|
|42252-52|1952-1966|Rod and Clevis|Brake Rod|K Models, Sportsters|
|42253-52|1967-- |Rod and Clevis|Brake Rod|XLH, XLCH|
|42282-35A|1967-1974|Stud|Brake Switch Stud|XLH, XLCH|
|42375-77|1979-1981|#10-24 x 1/2" Oval Countersunk Head Screw|Rear Master Cylinder \\ Cover Screw|XL, XLCH, XLS|
|42375-82|1982-E1987|#10-24 x 1/2" Washer \\ Hex Head Screw|Rear Master Cylinder \\ Cover Bolt|Sportsters|
|42461-80|L1980-1985|Stud|Brake Pedal Stop Stud|XL, XLS|
|42470-76|1979- |Flat Head Screw|Brake Pedal Stop Screw|XL, XLCH|
|44107-72|1973|Mounting Pin|Front Brake Mounting Pin|XLH, XLCH|
|44048-83|1984-2003|3/8"-24 Bleeder Screw|(F-R) Brake Bleeder Screw|XL, XLS, XLX|
|44059-83|1984-1985|Guide Pin|Front Brake Caliper Guide Pin|XL, XLS, XLX|
|44134-72A|1973|3/8" x 16 x 2-1/4" 12 Point Head Bolt|Front Brake Caliper \\ Mounting Bolt|XLH, XLCH|
|44146-77|1978-1981|3/8"-24 Bleeder Screw|(F-R) Brake Bleeder Screw|XL, XLCH, XLS|
|44146-82|1982-E1987|3/8"-24 Bleeder Screw|(F-R) Brake Bleeder Screw|Sportsters|
|44156-52|1953|Stud|Front Brake Shoe Pivot Stud|K|
|44156-54|1954-1963|Stud|Front Brake Shoe Pivot Stud|KH, Sportsters|
|44156-64|1964-1972|Stud|Front Brake Pivot Stud|XLH, XLCH|
|44172-77|1978-1983|7/16" x 14 x 1-3/4" \\ Hex Head Bolt (grade 8)|Front Brake Inner Caliper Bolt|XL, XLCH, XLS, XLX|
|44173-77|1978-1983|Shoulder Bolt|Front Brake Caliper \\ Mounting Bolt (long)|XL, XLCH, XLS, XLX|
|44174-77|1978-1983|Shoulder Bolt|Front Brake Caliper \\ Mounting Bolt (short)|XL, XLCH, XLS, XLX|
|44175-77|1979-1981|5/16" x 18 Shouldered Screw|Rear Caliper \\ Mounting Screw (short)|XL, XLCH, XLS|
|44176-77|1979-1981|5/16" x 18 Shouldered Screw|Rear Caliper \\ Mounting Screw (long)|XL, XLCH, XLS|
|44189-77|1979-1981|Hex Head Bolt|Rear Caliper Halves Bolt|XL, XLCH, XLS|
|44201-82|1982-E1987|5/16" x 24 x 1" Hex Socket Head Bolt|Rear Brake Caliper \\ Mounting Bolt|Sportsters|
|44212-82|1982-E1987|Guide Pin Kit|Rear Caliper Guide Pins|Sportsters|
|44264-52|1952-1953|Shaft|Brake Operating Shaft|K, KK|
|44264-54|1954-1963|Shaft|Brake Operating Shaft|KH, Sportsters|
|44264-64|1964-*|Shaft|Brake Operating Shaft|XLH, XLCH|
====== Body Parts ======
\\
===== Frame =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|2008|1982-E1984|Oval Head Screw|Left Side Cover Screw|XL, XLS|
|1357W|L1984-1985|1/4" x 20 x 1" Pozidriv \\ Oval Countersunk Head Screw|Left Side Cover Screw|XL, XLS, XLX|
|2882W|1967-1972|5/16" x 18 x 5/8" Hex Head Bolt|Included with \\ Frame Adapter Kit (47385-75)|XLH|
|:::|1970-1972|:::|:::|XLCH|
|3010|1979-1981|Knurled Slotted Head Screw|Right Side Cover Screw|XL, XLCH, XLS|
|3204W|1967-1972|1/4" x 20 x 5/8" Self Tapping \\ Slotted Hex Head Screw \\ (w / ext. tooth LW)|Included with \\ Frame Adapter Kit (47385-75)|XLH|
|:::|1970-1972|:::|:::|XLCH|
|3738|1967-1972|1/4" x 20 x 5/8" Hex Head Bolt|Included with \\ Frame Adapter Kit (47385-75)|XLH|
|:::|1970-1972|:::|:::|XLCH|
|3953W|1967-1972|5/16" x 24 x 1/2" Hex Head Bolt \\ (Grade 5, Cadmium)|Included with \\ Frame Adapter Kit (47385-75)|XLH|
|:::|1970-1972|:::|:::|XLCH|
===== Engine Guard / Rear Safety Guard =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|3956|1952-1962|5/16" x 24 x 9/16" Hex Head Bolt|Engine Guard \\ Top Mount Bolt|K Models, Sportsters|
|3974HW|1963-1978|5/16-24" x 3/4" Hex Head Bolt|Upper Front Engine \\ Guard Bolt|XLH, XLCH|
|4336|1957-- |3/8" x 24 x 1-1/8" Hex Head Bolt|Engine Guard Lower \\ Mount Bolt \\ (Replaced by Bolt #4335W in 1968)|XL, XLH|
|4336W|1957-1978|3/8" x 24 x 1-1/8" Hex Head Bolt|Lower Engine Guard Bolt|XL, XLH|
|4372|1964-- |3/8" x 24 x 1-5/8" Hex Head Bolt|Paired with Rear Safety \\ Guard Kit for 1957-up \\ Lower Left Side Bolt| XL, XLH|
|4372W|1957-+ |3/8" x 24 x 1-5/8" Hex Head Bolt|Paired with Rear Safety \\ Guard Kit for 1957-up \\ Lower Right? Side Bolt| XL, XLH|
===== Fuel Tank =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|907|1983-1985|Screw|Fuel Sending Unit Plate Screw|XLS|
|919|1983-1985|Screw|Gas Tank Console Trim Screw|XLS|
|2060|1952-1956|#4-40 x 3/16" Recessed Head Screw|Gas Tank Name Plate Screw|K, KH|
|2061W|1963-1976|#4-40 x 3/16" \\ Truss Head Screw|Gas Tank Name Plate Screw|XLH|
|2070|1959-1960|#6-32 x 5/64" Oval Head \\ Self Tapping Screw|Gas Tank Name Plate Screw|XLH|
|2072W|1961-1962|#6-32 x 3/8" Self Tapping \\ Fillister Head Screw|Gas Tank Name Plate Screw|XLH|
|2551W|1980-1981 \\ L1983-1985|1/4" x 20 x 1" Hex Head Bolt|Gas Tank Front Mounting Bolt \\ Gas Tank Long Bracket Bolt|XLS|
|2667|1982-1983 \\ E1982 \\ L1982|5/16" x 18 x 2-1/2" Hex Head Bolt|Gas Tank and Coil \\ Mounting Bracket Bolt|XLS \\ XL \\ XLHA, XLSA|
|3419|1982|5/16" x 18 x 2-14" Hex Head Bolt|Front Gas Tank Bracket Bolt|XLS|
|3651|1983-1985|Screw|Gas Tank Console Screw|XLS|
|4060W|1958-1976|5/16" x 24 x 2-1/4" Hex Head Bolt|Small Gas Tank Rear Mount Bolt|XLCH|
|4068|1982-E1983 \\ E1982 \\ L1983-1984|5/16" x 18 x 2-1/2" Hex Head Bolt|Rear Gas Tank Bracket Bolt|XL \\ XLS \\ XR-1000|
|4072|1958-E1972|5/16" x 24 x 2-5/8" Hex Head Bolt|Small Gas Tank Front Mount Bolt|XLCH|
|4082|1952-1975|5/16" x 18 x 3-1/6" Hex Head Bolt \\ (replaced by 30013-71 in '75)|Large Gas Tank Front Mount Bolt|K Models, Sportsters|
|4083W|1967-1972|5/16" x 24 x 3-3/4" Hex Head Bolt|Gas Tank Front Mount Bolt|XLH|
|4391|E1982 \\ 1983-1985|5/16" x 24 x 5/8" Hex Head Bolt|Gas Tank and Coil \\ Mounting Bracket Bolt|XL \\ XLS|
|4710|1958-1978|5/16" x 24 x 2-1/4" Hex Head Bolt|Rear (small) \\ Gas Tank Mounting Bolt|XLCH|
|4723|1979-1981|5/16" x 24 x 2-1/2" Hex Head Bolt|Gas Tank \\ Rear Mounting Bolt|XL, XLCH|
|4725|L1972-1981|5/16" x 24 x 2-3/4" Hex Head Bolt|Small Gas Tank \\ Front Mount Bolt|XL, XLH, XLCH|
|30013-71|1954-1966 \\ 1972-1978|5/16" x 24 x 3-1/4" Hex Head Bolt|Large Gas Tank \\ Mounting Bolt|K, XL, XLH, \\ XLCH, XLT|
|47091-83|1983-1985|3" Stud|Front Gas Tank Mounting Stud|XLS|
|47096-83|1983-1985|2-7/8" Stud|Rear Gas Tank Mounting Stud|XLS|
===== Oil Tank =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|3738|1952-1971|1/4" x 28 x 1/2" Hex Head Bolt|Oil Tank Bracket Bolt|K Models, XL, XLH|
|3787|1970-1978|1/4" x 20 x 3/4" Hex Head Bolt|Oil Tank Bolt|XLCH|
|3791|1966-1969|1/4" x 28 x 3/4" Hex Head Bolt|Oil Tank Bolt|XLCH|
|3831|1966-1969|1/4" x 20 x 1" \\ Hex Head Bolt (drilled)|Lower Oil Tank Bracket Bolt|XLCH|
|3956|1967-1978|5/16" x 24 x 9/16" Hex Head Bolt|Oil Tank Mounting Bolt|XLH|
|3987|1972-1978 \\ 1980-1981|5/16" x 18 x 3/4" Hex Head Bolt|Oil Tank Bracket Bolt|XLCH \\ XL, XLS|
|3974|L1961-* |5/16" x 24 x 3/4" Hex Head Bolt|Oil Tank (front) Mount Bolt|XLCH|
|3996|1979-1981|5/16" x 24 x 7/8" Hex Head Bolt|Oil Tank Mounting Bolt|XL, XLCH, XLS|
|4012|1958-E1961|5/16" x 24 x 1-1/8" Hex Head Bolt|Oil Tank Mounting Bolt|XLCH|
|4293|1966-E1973|3/8" x 16 x 25/32" Hex Head Bolt|Oil Tank Bracket Mounting Bolt|XLCH|
|4293|1967-- |3/8" x 16 x 7/8" Hex Head Bolt|Oil Tank Lower Bracket Bolt|XLH|
|4348|1958-1965|3/8" x 16 x 1-3/16" Hex Head Bolt|Oil Tank Bracket Bolt|XLCH|
|4391|1982-1985|5/16" x 24 x 5/8" Hex Head Bolt|Oil Tank Mounting Bolt|XL, XLS|
|4392|L1984-1985|5/16" x 18 x 3-1/4" Hex Head Bolt|Oil Filter Pad Mounting Bolt|XL, XLS, XLX|
|4410|1966-E1977|1/4" x 28 x 3/4" Hex Head Bolt|Oil Tank Bolt|XLCH|
|4713W|1966-1978|3/8" x 16 x 3/4" Hex Head Bolt|Oil Tank Bracket Bolt|XLCH|
|62556-52|1958-1964|Bolt|Oil Tank Mounting Bolt|XLCH|
|62620-52|1954-E1966|Wing Nut Screw|Oil Tank Cap Screw|K Models, Xl, XLH|
|62620-66|L1966-1978|Wing Nut Screw|Oil Tank Cap Screw|XLH|
|62760-52|1952-1971|Stud|Oil Tank Mounting Stud|K Models, XL, XLH|
|62761-66|1966-1969|Stud|Oil Tank Mounting Stud|XLCH|
===== Fenders =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|919|1982-1985|1/4“ x 28 x 3/4” Hex \\ Socket Head Screw|Front Chain Guard Screw|XL, XLS, XLX|
|2215| 1968-1978|#10-24 x 9/16" Screw|Front Fender Lamp \\ Kit (59260-68) \\ Lamp Base Screw|XLH|
|2272|1973-1978|5/16" x 24 x 1-1/4" Pozidriv \\ Countersunk Oval Head Screw|Rear Fender Support Screw|XLH, XLCH|
|2401|1968-1978 \\ 1970-1978|#10-24 x 5/8" Pozidriv \\ Countersunk Oval Head Screw|Front Fender Light Base Screw|XLH \\ XLCH|
|2414W|1952-- |5/16" x 18 x 1-1/8" Oval Head Screw|Fender Mounting Bolt|K Models, Sportsters|
|:::|1962-- |:::|Exhaust Mount Bolt|XLH, XLCH|
|2587|1968-1978 \\ 1970-1978|#10-32 x 5/8" Pozidriv \\ Pan Head Screw|Front Fender Light \\ Terminal Screw|XLH \\ XLCH
|2630W|1968-1978 \\ 1970-1978|#8-32 x 5/16" Self Tapping \\ Round Head Screw|Front Fender \\ Lamp Kit (59260-68) \\ Lens Screw|XLH \\ XLCH|
|2630W|1966-1967|#8-32 x 5/16" Self Tapping \\ Round Head Screw:::|Fender Tip Screw|XLH, XLCH|
|:::|1968-1978 \\ 1970-1978|:::|Front Fender Light \\ Lens Screw|XLH \\ XLCH|
|2634W|1966-1978|#8 x 1/2" Self Tapping \\ Round Screw|Fender Tip Screw|XLH, XLCH|
|2659|1968-1978 \\ 1970-1978|#10-24 x 7/8" Pozidriv \\ Pan Head Screw|Front Fender Lamp \\ Terminal Screw|XLH \\ XLCH|
|2684W|1968-?|#10-32 x 5/8" Round Head Screw|Front Fender \\ Lamp Kit (59260-68) \\ Fender Terminal Screw|XLH|
|2686|1968-?|#10-24 x 7/8" Round Head Screw|Front Fender \\ Lamp Kit (59260-68) \\ Lamp Terminal Screw|XLH|
|2882W|1974-1983|5/16" x 18 x 5/8" Hex Head Bolt|Front Fender Mounting Bolt|XLH, XLCH, XLS|
|3005W|1968- |#6-32 x 3/16" Self Tapping Screw|Front Fender \\ Lamp Kit (59260-68) \\ Lamp Socket Screw|XLH|
|:::|1968-1978 \\ 1970-1978|:::|Front Fender \\ Lamp Mounting Screw|XLH \\ XLCH|
|3210|1984-1985|5/16" x 18 x 1-1/4" Socket Head Screw|Front Fender Mounting Bolt|XL, XLS, XLX|
|3491|1968-1978 \\ 1970-1978|#8-32 x 5/8" Hex Head Screw|Front Fender Wire \\ Terminal Screw|XLH \\ XLCH|
|3491|1968-1978|#8-32 x 5/8" Hex Head Screw|From Front Fender \\ Lamp Kit (59260-68) \\ Fender Cable Screw|XLH|
|:::|1970-1978|:::|:::|XLCH|
|3685|1982-1990|5/16" x 18 x 1" Hex Socket Head Screw|Rear Fender Mounting Bolt|Sportsters|
|3720|1970-1974|1/4" x 28 x 7/16" Hex Head Bolt|Fender Mounting Bolt|XLH, XLCH|
|3741|1952-1973|1/4" x 28 x 1/2" Hex Head Bolt|Rear Fender (front) Bracket Screw \\ (replaced by 3765)|K Models, Sportsters|
|3765|1974-1978|1/4" x 28 x 5/8" Hex Head Bolt|Rear Fender (front) Bracket Bolt \\ (replaced 37415)|K Models, Sportsters|
|3765|1982-1985|1/4" x 28 x 5/8" Bolt|Fender Extension Bracket Bolt|XL, XLS|
|3767B|1982-1985|1/4" x 20 x 5/8" Hex Head Bolt|Seat to Fender Mounting Bolt|Sportsters|
|3781A|1982-1985|5/16" x 18 x 1-1/4" Hex \\ Socket Head Bolt|Rear Fender Mounting Bolt|XL, XLS|
|3791|1953-1955|1/4" x 28 x 3/4" Hex Head Bolt|Chain Guard Bolt|K, KH|
|3948|1952-1969|5/16" x 24 x 7/16" Hex Head Bolt|Rear Fender Brace Screw|K Models, Sportsters|
|3953W|1952-1955|5/16" x 24 x 1/2" Hex Head Bolt \\ (Grade 5, Cadmium)|Rear Chain Guard Mounting Bolt|K Models|
|:::|1973-1979|:::|Front Chain Guard Mounting Bolt|XL, XLH, XLCH, XLS|
|3954B|1967-1971|5/16" x 24 x 1/2" Hex Head Bolt|Rear Chain Guard \\ 60308-67, (rear) Bolt|XLH|
|3956|1956-1966|5/16" x 24 x 9/16" Hex Head Bolt|Rear Chain Guard \\ Mounting Screws|KH, Sportsters|
|:::|1967-- |:::|:::|XLH|
|3960W|1979-1981|5/16" x 24 x 1" Hex Head Bolt|Rear Fender Mounting Bolt|XL, XLCH, XLS|
|3974W|1970-1978|5/16" x 24 x 3/4" Hex Head Bolt|Fender Mounting Bolt|XLH, XLCH|
|3974HW|1982-1984|5/16" x 24 x 3/4" Hex Head Bolt|Lower Chain Guard Bolt|XL, XLS|
|3991|1973|5/16" x 24 x 7/8" Hex Head Bolt|Front Fender Mounting Bolt|XLH, XLCH|
|4020|1954-- |5/16" x 24 x 1-3/8" Hex Head Bolt|Luggage Rack Mounting Bolt|KH, Sportsters|
|4020|1967-+ |5/16" x 24 x 1-3/8" Hex Head Bolt|Rear Chain Guard \\ 60308-67, (front) Bolt|XLH|
|4020W|1954-1969|:::|Luggage Rack Mounting Bolt|KH, Sportsters|
|4020W|1967-1972 \\ 1970-1972|:::|Rear Chain Guard \\ 60308-67, (front) Bolt|XLH \\ XLCH|
|4036|1979-1981|5/16" x 24 x 1-1/2" Hex Head Bolt|Rear Fender Mounting Bolt|XL, XLCH, XLS|
|4081|1982-1985|1/2" x 20 x 1-3/4" Hex Head Bolt|Chain Guard Rear Bolt|XL, XLS, XLX|
|4362|1953-E1973|3/8" x 24 x 1-3/8" Hex Head Bolt|Fender Support Mounting Bolt|K Models, Sportsters|
|4391|1973-1978|5/16" x 24 x 5/8" Hex Head Bolt|Rear Chain Guard Bolt|XLH, XLCH|
|4081|1982-1983|1/2" x 20 x 1-3/4" Hex Head Bolt|Chain Guard Mounting Bolt|XL, XLS|
|4411|1979-1981|3/8" x 24 x 1-3/4" Hex Head Bolt|Chain Guard Mounting Bolt|XL, XLCH, XLS|
|4724|1973-1978|3/8" x 24 x 1-1/2" Hex Head Bolt|Rear Fender Support Bolt|XLH, XLCH|
|42450-80|1982- |1/2" x 13 x 2" Hex Head Bolt|Chain Guard Mounting Bolt|XL, XLS|
|45995-73|1983-1987|Screw|Front Chain Guard Screw|Sportsters|
|53454-52|1954-1969|Long Stud Threaded Both Ends|Luggage Rack Cross Brace|KN, Sportsters|
===== Toolbox =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|64500-52A|1952-1966|Wing Nut Screw|Tool Box Mounting Bolt|K Models, XL, XLH|
===== Saddlebags, Luggage Racks =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|3738|1966-1978|1/4" x 28 x 1/2" Hex Head Bolt|Saddlebag Guard Bolt|XLH|
|3825|1966-1978|1/4" x 28 x 5/8" Hex Head Bolt|Saddlebag Bracket Mounting Bolt|XLH, XLCH|
|3956|1952-1965|5/16" x 24 x 9/16" Hex Head Bolt|Saddlebag Carrier Plate Bolt|K Models, XL, XLH|
|:::|1965|:::|:::|XLCH|
|3991|1966- |5/16" x 24 x 7/8" Hex Head Bolt|Saddlebag Front Mounting Bolt|XLH, XLCH|
|4014W|1952-1965|5/16" x 24 x 1-1/4" Hex Head Bolt|Saddlebag Carrier Bolt|K Models, XL, XLH|
|:::|1965|:::|:::|XLCH|
|:::|L1969-1978|:::|5/16" x 24 x 1-1/4" Hex Head Bolt|Saddlebag Carrier Bolt
|4014W|1966-E1969|5/16" x 24 x 1-1/4" Hex Head Bolt|Saddlebag Carrier Mounting Bolt \\ (not used with luggage rack)|XLH, XLCH|
|4014W|L1969-1978|5/16" x 24 x 1-5/8" Hex Head Bolt|Saddlebag Carrier Mounting Bolt|XLH, XLCH|
|:::|Discrepancy between -76A (4041W) and -78A (4014W) parts books but both are 1-5/8" long.||||
|4036|1966-E1969|5/16" x 24 x 1-1/2" Hex Head Bolt|Saddlebag Carrier Mounting Bolt \\ (used with luggage rack) \\ (replaced 4042HW)|XLH|
|:::|1954-1978|:::|Luggage Rack Mounting Bolt|KH, XL, XLH, XLCH|
|4041W|1966- |5/16" x 24 x 1-1/2" Hex Head Bolt|Handrail Bolt|XLH, XLCH|
|4042HW|1966|5/16" x 24 x 1-3/4" Hex Head Bolt|Saddlebag Carrier Mounting Bolt \\ (used with luggage rack) \\ (Replaced by bolt #4036)|XLH|
|90907-61|1954-1965|Stud|Saddlebag Mounting Stud|KH, XL, XLH|
|:::|1965|:::|:::|XLCH|
|90939-66|1966-- |Clip|Saddlebag Hinge Clip|XLH, XLCH|
===== Seats =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|919|1982 \\ L1983-1985|1/4" x 28 x 3/4" Hex \\ Socket Head Screw|Sissybar to Frame Screw|XLS \\ XL, XLS, XLX|
|1000|1980-1983|1/4" x 20 x 3/16" Screw|Pillion Seat Mounting Screw \\ Backrest Bracket (2 hole) Screw|XL, XLS|
|1602|1982|1/4" x 20 x 3/4" Pozidriv \\ Flat Countersunk Head Screw (grade 2)|Center Pillion Seat Screw|XLS|
|1661B|1970-1971|#6-32 x 1/2" Countersunk Head Screw|Thru Seat \\ Taillight Clip Screw|XLH, XLCH|
|2551W|L1972-1978|1/4" x 20 x 1" Hex Head Bolt|Seat to Fender Bolt|XLH, XLCH|
|2607|1980-1981|1/4" x 20 x 1/2" Pozidriv \\ Pan Head Screw|Seat Bracket Screw|XLS|
|:::|1980-1982|1/4" x 20 x 3/4" Pozidriv \\ Pan Head Screw|Sissybar Nameplate Screw|XLS|
|2623W|1954-1974 \\ 1970-1974|#8-15 X 5/8" \\ Self Tapping Screw|Expansion Nut Screw|XLH \\ XLCH|
|2625|1970-1971|#8-32 x 5/8" Pozidriv \\ Pan Head Screw|License Plate Light \\ Ground Wire Screw|XLH, XLCH|
|2630W|1970-1971|#8-32 x 5/16" \\ Self Tapping Screw|License Plate Light \\ Ground Wire Screw|XLH, XLCH|
|2637|1982- |#4-24 x 3/8" Self Tapping \\ Phillips Head Screw|Pillion Seat Outer Screw|XL, XLS|
|2711|1982|#4-40 x 3/8" Self Tapping \\ Pan Head Screw|Backrest Mounting Screw|XLS|
|2757W|1979-1985|1/4" x 28 x 7/16" Phillips Head Screw|Passenger Seat \\ to Fender Screw|XL, XLCH, XLS, XLX \\ XR-1000|
|2757W|L1983-1984 \\ 1986-1990|1/4" x 28 x 7/16" Phillips Head Screw|Passenger Seat \\ Hole Screw|XR-1000 \\ All Models|
|3728|1954-1978 \\ 1970-1972 \\ 1972-1978|1/4" x 20 x 1/2" Hex Head Bolt|Dual Seat Frt. Bracket \\ to Seat Bolt \\ (replaced by 3767B) \\ Also Incl. w/ \\ Handrail Kit (52617-72)|K Models, Sportsters \\ XLCH|
|3767B|1952-1985|1/4" x 20 x 5/8" Hex Head Bolt|Dual Seat Frt Bracket Clip Bolt \\ Dual Seat Rr Bracket Clip Bolt|K Models, Sportsters|
|3787|1970-1971|1/4" x 20 x 3/4" Hex Head Bolt|Boat Seat Base \\ Mounting Bolt|XLH, XLCH|
|3794W|1970-1971|1/4" x 14 x 7/8" Self Tapping \\ Hex Head Screw|Boat Seat to \\ Base Screw|XLH, XLCH|
|3802W|1970-1971|1/4" x 20 x 7/8" Hex Head Bolt|Boat Seat Guardrail Bolt|XLH, XLCH|
|3825|1966-1978|1/4" x 28 x 5/8" Hex Head Bolt|Saddlebag Cross Brace Bolt|XLH, XLCH|
|3953W|1952-1962|5/16" x 24 x 1/2" Hex Head Bolt \\ (Grade 5, Cadmium)|Buddy Seat Front/Rear \\ Bracket and Handrail Bolt \\ (replaced by 3974 in 1963)|K Models, Sportsters|
|:::|Replaced by #3974 in 1963 for Buddy Seat Brackets.||||
|3956|1952-1970|5/16" x 24 x 9/16" Hex Head Bolt|(R) Single Seat to Bracket Bolt|K Models, Sportsters|
|3960W|1954-1970|5/16" x 24 x 1" Hex Head Bolt|Seat Post Retainer Bolt|KH, XL, XLH, XLCH|
|3974 \\ 3974HW|1952-1978|5/16" x 24 x 3/4" Hex Head Bolt|Seat Retainer Plate Bolt|K Models, Sportsters|
|:::|:::|:::|Buddy Seat (F-R) Bracket \\ and Handrail Bolt \\ (replaced 3953W)|K Models, Sportsters|
|:::|1980|:::|Passenger Strap Bolt|XL, XLS|
|3987|1983-1985|5/16" x 18 x 3/4" Hex Head Bolt|Passenger Strap Bolt|XLS|
|3991|1966-1971|5/16" x 24 x 7/8" Hex Head Bolt|Long Dual Seat \\ Front Bracket Bolt|
|3996|1952-1978|5/16" x 24 x 7/8" Hex Head Bolt|Dual Seat (rear) Bracket Bolt|K Models, Sportster|
|:::|1981|:::|Passenger Strap Bolt|XL, XLS|
|4000|1968-1970|5/16" x 24 x 1" Hex Head Bolt|Single Seat \\ Retainer Plate Bolt|XLCH|
|4017|1970-1971|5/16" x 18 x 1" Hex Head Bolt|Boat Seat Base \\ Mounting Bolt|XLH, XLCH|
|4020|1952- |5/16" x 24 x 1-3/8" Hex Head Bolt|Single Seat to \\ Bracket Bolt (front)|K Models, Sportsters|
|4020W|1952-1969|:::|Single Seat to (F) Bracket Bolt|K Models, Sportsters|
|:::|1970-1971|:::|Boat Seat Base Mounting Bolt|XLH, XLCH|
|4041W|1966-1978|5/16" x 24 x 1-1/2" Hex Head Bolt|Buddy Seat Handrail Bolt|XLH, XLCH|
|4080|1952-1971|5/16" x 18 x 2-3/4" Hex Head Bolt|Seat Bolt|K Models, Sportsters|
|4082|1952- |5/16" x 18 x 3-1/6" Hex Head Bolt|Buddy Seat (front) Bracket Bolt|K Models, Sportsters|
|4086|1953-1960|5/16" x 18 x 3" Hex Head Bolt|Seat Front Bolt|K Models and Sportsters|
|4092|1982-1990|5/16" x 18 x 3/4" Hex \\ Socket Head Screw|Passenger Strap Bolt|Sportsters|
|4372|1952- |3/8" x 24 x 1-5/8" Hex Head Bolt|Buddy Seat Rear Bracket Bolt|K Models, Sportsters|
|4372W|1954- |3/8" x 24 x 1-5/8" \\ Hex Head Bolt (Cadmium)|(R) Buddy Seat Bracket Bolt|KH, Sportsters|
|4411|1954-1976|3/8" x 24 x 1-3/4" Hex Head Bolt|Large Tank (R) Bracket Bolt \\ For Buddy Seat \\ (replaced by 4724 in '77)|
|4679P|1966- |Screw|Rear Trim Strip Screw (dual seat)|XLH, XLCH|
|4724|1954-1978|3/8" x 24 x 1-1/2" Hex Head Bolt|Large Tank (R) Bracket Bolt \\ For Buddy Seat \\ (replaced 4411 in '77)|KH, XL, XLH, XLCH|
|4826|1953-1958|1/2" x 20 x 1-7/8" Hex Head Bolt|Seat to Post Bolt|K Models, Sportster|
|30013-71|1954-1978|5/16" x 24 x 3-1/4" Hex Head Bolt|Small Tank Bracket Bolt \\ for Buddy Seat|KH, XLH, XLCH|
|4826HB|1953-1958|1/2" x 20 x 1-7/8" Hex Head Bolt|Seat to Post Bolt|K Models, XL, XLH|
|51950-52|1952-1970|Special Bolt|Seat Saddle Bar Bolt|K Models, Sportsters|
|52102-66P|1966- |Screw|Buddy/Dual Seat \\ Trim Strip Screw|XLH, XLCH|
===== Handlebars, Hand Levers, Cable Clips =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|853|1983-1984|5/16" x 24 x 2-1/4" Socket \\ Round Head Screw|Throttle Control Clamp Screw|XLS|
|:::|L1983-1984|5/16” x 24 x 2-1/4“ Hex Head Bolt|Bracket to \\ Upper Handlebar Clamp Bolt|XR-1000|
|916|1981-1982|#8-32 x 5/8" Fillister Head Screw|Throttle Control Clamp Screw|XL, XLS|
|991|1954-1964|#10-24 x 1" Pozidriv \\ Fillister Head Screw|Front Brake Lever Bracket Screw|XL, XLH, XLCH|
|1203|1974-1981|#8-32 x 7/8" Pozidriv \\ Fillister Head Screw|Throttle Control Clamp Screw|XLH, XLCH, XLS|
|1205|1965-1978|#10-24 x 3/4" Pozidriv \\ Fillister Head Screw|Clutch Lever Bracket Screw|XLH, XLCH|
|:::|1965-1972|:::|Front Brake Lever Bracket Screw|XLH, XLCH|
|1206W|1965-- |#10-24 x 3/4" Fillister Head Screw|Clutch / Brake Lever Clamp Screw|XLH, XLCH|
|1207W|1965|#10-24 x 5/8" Fillister Head Screw|Clutch Hand Lever \\ Bracket Screw \\ (replaced by 1206W in 1966)|XLH, XLCH|
|1214|1952-1964|#10-24 x 3/4" Fillister Head Screw|Clutch/Brake Lever \\ Bracket Screw|K Models, Sportsters|
|1214HW|1954-1964|#10-24 x 3/4" Fillister Head Screw|Clutch Lever Clamp Screw|KH, Sportsters|
|:::|1954-1964|:::|Front Brake Lever Clamp Screw|KH, Sportsters|
|1300|1952-* |#12-24 x 1/2" Fillister Head Screw|Clutch Control Coil Bracket|K Models, Sportsters|
|1300B|1954-E1970|#12-24 x 1/2" Fillister Head Screw|Clutch Cable Clamp Screw|KH, Sportsters|
|2585|1970-1973|#8-32 x 5/16" Posidriv \\ Pan Head Screw|Carburetor Control \\ Wire Clamp Screw|XLH, XLCH|
|2592|1961-1972|#10-24 x 1/2" Pozidriv \\ Pan Head Screw|Front Brake Cable \\ Tube Clamp Screw|XLH, XLCH|
|2633|1961-1972|#8-32 x 3/8" Self Tapping Screw|Wire Coil Clamp|XLH, XLCH|
|2660|1979-1983|#10-24 x 3/8" Pozidriv \\ Pan Head Screw|Handlebar Ground Wire Screw \\ (replaced by 2662W in '84)|XL, XLCH, XLS|
|2662W|1979-1985|#10 x 24 x 3/8" Self Tapping \\ Phillips Round Head Screw|Handlebar Ground Wire Screw|XL, XLCH, XLS|
|2664|1973-1977|#10-24 x 7/16" Pozidriv \\ Pan Head Screw|Front Brake Hose Clip Screw|XL, XLCH|
|2666|1952-1960|#10-24 x 5/16" Round Head Screw|Front Brake Cable Clamp Screw|K Models, Sportsters|
|2666B|1954-1960|#10-24 x 5/16" Round Head Screw|Front Brake Cable Clamp Screw|KH, Sportsters|
|2669|1961- |#10-24 x 3/8" Round Head Screw|Front Brake Cable Clamp \\ Replaced by Screw# 2669W|Sportsters|
|2669W|1961- |#10-24 x 3/8" Round Head Screw|Front Brake Cable Clamp \\ Replaced Screw #2669|Sportsters|
|2672|1961- |#10-24 x 1/2" Round Head Screw|Front Brake Cable Clamp Screw|XLH, XLCH|
|2672B|1961- |#10-24 x 1/2" Round Head Screw|Front Brake Cable Clamp Screw|XLH, XLCH|
|2695 \\ 2695W|1973-1981|#10-24 x 1-1/8" \\ Phillips Head Screw \\ #10-24 x 1-1/8" Pozidriv \\ Fillister Head Screw|Clutch Lever Bracket Screw|Sportsters|
|:::|1973-1976|:::|Handlebar Switch Housing Screw|:::|
|2751|1961-1978|1/4" x 28 x 5/16" \\ Round Head Screw|Throttle Control Coil Clamp|XLH|
|2758|1959- |1/4" x 20 x 1/2" \\ Round Head Screw|Handlebar Clamp Cover|XLH|
|:::|1965- |:::|Handlebar Clamp Cover Screw|XLCH|
|2808|1976|#8-32 x 3/8" Pozidriv \\ Pan Head Screw|Coil Wire Clamp Screw|XLH, XLCH|
|:::|1980-1985|:::|Clutch Cable Clamp Screw|XL, XLS|
|2902|L1983-1984|1/4" x 20 x 1/2" Pozidriv \\ Fillister Head Screw (Grade 2)|Throttle Housing Screw|XR-1000|
|3207|1954-1978|#10-32 x 3/16" Hex \\ Socket Set Screw|Handlebar Control Wire \\ Plunger Set Screw|KH, Sportsters|
|:::|1954-1973|:::|:::|XLCH|
|3208|1974-1980|#8-32 x 5/8" Socket Head Set Screw|Throttle Cable Stop|XLH, XLCH, XLS|
|3210|1974-1981|5/16" x 18 x 1-1/4" \\ Socket Head Bolt|Handlebar Clamp Bolt|XLH, XLCH, XLS|
|3431|1983-1985|1/2" x 13 x 3-1/4" Hex Head Bolt|Handlebar Lower Clamp Bolt|XLS|
|3450|1979-1980 \\ 1982|1/2" x 13 x 2-1/2" Hex Head Bolt|Handlebar Lower Clamp Bolt|XLS|
|3498|E1984|1/2" x 13 x 3" Hex Head Bolt|Handlebar Lower Clamp Bolt|XL, XLX|
|3778|1974-1985 \\ 1981-1982|1/2" x 13 x 3-3/4" Hex Head Bolt|Handlebar Lower Clamp Bolt|XLH, XLCH \\ XLS|
|4015|1982-1985|1/4" x 20 x 7/8" Hex \\ Socket Round Head Screw|Clutch Lever Bracket Screw|Sportsters|
|4816|1979-1990|5/16" x 18 x 1-5/16" \\ Socket Head Bolt|Bracket to Upper \\ Handlebar Clamp Bolt|Sportsters|
|4088|1974-1976|1/2" x 13 x 3-1/2" Hex Head Bolt|Handlebar Clamp to Fork Bolt|XLH, XLCH|
|4335W|1952-1960|3/8" x 24 x 1-1/8" Hex Head Bolt|Handlebar Clamp Cover|K Models, Sportsters|
|:::|This part number replaced bolt #4336 and #4336W in 1968.||||
|4336W|1952-1960|3/8" x 24 x 1-1/8" Hex Head Bolt|Handlebar Clamp Cover|K Models, Sportsters|
|4337W|1961- |3/8" x 24 x 1-1/4" Hex Head Bolt \\ (grade 5, zinc, NF)|Handlebar Clamp Cover|XLCH|
|4414|1973|1/2" x 20 x 2-1/2" Hex Head Bolt|Handlebar Lower Clamp Bolt|XLH, XLCH|
|45031-41|1952-1964|Pivot Screw|Brake/Clutch Lever \\ Pivot Screw|K Models, Sportsters|
|45159-50|1952-1972|Screw|Front Brake Control \\ Wire Adjustment Screw|K Models, Sportsters|
|45159-50|1971-E1977|Screw|Clutch Coil Wire Adjusting Screw|XLH, XLCH|
|56105-84|L1984-1990|Stud|Handlebar Lower Clamp Stud|Sportsters|
|56154-52|1952-1972|1/2" x 20 x 2-7/8" Hex Head Bolt|Handlebar Mounting Screw|K Models, Sportsters|
|56240-47|1953|Screw|Grip Retainer Screw|K|
|56276-31|1952-1978|#10-32x 1/4" Set Screw ((Bretton of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/203462-thread-size-for-56276-31#post5932631)) |Coil Plug Set Screw|KH, XL, XLH|
|56397-74|1974-1983|Knurled Screw|Throttle Control Adj Screw|XLH, XLCH, XLS|
|56402-83 \\ 56402-83A|1979-1990|Screw|Throttle Adj Screw \\ (from grip kits \\ 56397-83 or 56397-74B)|Sportsters|
|56610-52|1954-1956|Screw|Handlebar Control \\ Coil Clamp Screw|KH|
|56288-53|1953-1978|Screw|Handlebar End Screw|K Models, Sportsters|
===== Mirror =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|3233|1979-1984|1/4" x 28 x 1/8" \\ Socket Head Set Screw|Mirror to Stem Screw|
|:::|(from mirror kits 91875-77A, 91875-82, 91878-77A, 91892-82, 91896-83)||||
===== Foot Controls / Pegs =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|855|1983-1990|3/8" x 16 x 2" Knurled Socket Head Screw|Screw for Swingarm Mounted \\ Bracket for Passenger Peg \\ Peg Mounting Bolt|Sportsters|
|2608|L1981-1985|5/16"-18 x 1-1/2" Socket Head \\ (shouldered) Screw|Right Footpeg Mounting Bolt|
|2818|1975-1976|5/16" x 18 x 1-1/2" Hex Head Bolt|Cross Shifter Lever \\ to Shaft Bolt|XL, XLCH|
|2871 \\ 2871W|L1972-1974|5/16" x 18 x 1-1/4" Hex Head Bolt|Shifter Arm Cinch Bolt|XLH, XLCH|
|2871W|1975-1976|5/16" x 18 x 1-1/4" Hex Head Bolt|Shifter Shaft Lever \\ Cinch Bolt|XLH, XLCH|
|2872W|1975-1976|1/4" x 20 x 1-1/4" Hex Head Bolt|Cross Shifter Lever \\ Cinch Bolt|XLH, XLCH|
|2887W|1975-1976|5/16" x 18 x 1-3/4" Hex Head Bolt|Brake Pedal Bolt|XLH, XLCH|
|3791|1952-1974|1/4" x 28 x 3/4" Hex Head Bolt|Rear Brake Cross Lever Bolt|K Models, Sportsters|
|3825|1961-1974|1/4" x 28 x 1" Hex Head Bolt|L-R Footrest Support Cinch Bolt|XLH, XLCH|
|3826|1961-1978|1/4" x 28 x 1-1/4" Hex Head Screw|L-R Footrest Support Cinch Bolt|XLH, XLCH|
|3840|1952-1960|1/4" x 28 x 1-1/4" Hex Head Bolt|L-R Footrest Support Cinch Bolt|K Models, Sportsters|
|3945|1979-1981|3/8" x 24 x 2-1/4" Hex Head Bolt|Passenger Peg to \\ Frame Bracket Bolt|XL, XLCH, XLS|
|3984|1953|5/16" x 18 x 1-1/16" Hex Head Bolt|Shifter Lever Stop Bolt|K|
|4012|1953-1958|5/16" x 24 x 1-1/8" Hex Head Bolt|Passenger Footrest Bracket Bolt|K Models, XL, XLH|
|4012|1952- |5/16" x 24 x 1-1/8" Hex Head Bolt|Replaced by #3791 in 1963 catalog \\ for Shifter Lever Cinch Bolt|K Models, Sportsters|
|4012|1964-1966|5/16" x 24 x 1-1/8" Hex Head Bolt|Heel-Toe Shifter Lever Cinch Bolt \\ (Replaced by 4014W in 1967)|XLH, XLCH|
|4014W|1964-E1972|5/16" x 24 x 1-1/4" Hex Head Bolt|Heel-Toe Shifter Lever Cinch Bolt \\ (Replaced 4012 in 1967)|XLH, XLCH|
|4036|1954-1974|5/16" x 24 x 1-1/2" Hex Head Bolt|Cross Brake \\ Pedal Arm Cinch Bolt|K Models, Sportsters|
|4319|1982|3/8" x 24 x 1" Hex Head Bolt|Footrest Support Bar \\ to Frame Bolt|XL, XLS|
|4362|1953-1958|3/8" x 24 x 1-3/8" Hex Head Bolt|Left Footrest Bracket Bolt|K Models, Sportsters|
|4401W|1980-1981 \\ L1981|3/8" x 24 x 2-3/4" Hex Head Bolt|Highway Peg Bracket Bolt|XL \\ XLS|
|4410|1954-1974|1/4" x 28 x 7/16" Hex Head Bolt|Cross Brake Pedal Bolt|K Models, Sportsters|
|4412|1954-1978 \\ 1980-1981|3/8" x 24 x 2-1/2" Hex Head Bolt|Footrest Support \\ Bracket Mounting Bolt|KH, Sportsters|
|4435W|1982-1985|3/8" x 24 x 3-1/2" Hex Head Bolt|Footrest Support Bar \\ to Frame Bolt|XL, XLS|
|4452B|1952-- |3/8" x 24 x 2-1/2" Hex Head Bolt|Passenger Footrest Support \\ Mounting Bolt|K Models, Sportsters|
|4640|1980-1985|7/16" x 20 x 1" Hex Head Bolt|Highway Peg Bracket Bolt|XLS|
|4701|1977-1978|5/16" x 24 x 1-1/2" Hex Head Bolt|Brake Pedal Bolt|XL, XLCH|
|4703|1980- |7/16" x 20 x 7/8" Hex Head Bolt|Highway Peg Bracket Bolt|XLS|
|4721|L1972-1978|3/8" x 16 x 1-1/2" Hex Head Bolt|Included in Rear Footrest \\ Kits (50907-69A), (49106-77)|XLH, XLCH|
|:::|1979-1981 \\ 1983-1985 \\ L1984-1985 \\ 1986-1990|:::|Front/Rear Highway \\ Peg Mounting Bolt|XL, XLCH, XLS \\ XLX \\ XLS \\ Sportsters|
|4724|1982-1985|3/8" x 24 x 1-1/2" Hex Head Bolt|Passenger Peg Bolt|XL, XLS|
|4729|1956-1984 \\ 1979|7/16" x 20 x 1-1/4" Hex Head Bolt|Highway Peg Bracket Bolt \\ (highway footrest \\ kit 49106-77)|XL, XLCH \\ XLS|
|24751-75|1977-1985|1/2" x 3-7/8" Stud|Right Footrest Stud|XLH, XLCH, XLS|
|24752-75|1977-1979|1/2" x 5-3/4" Stud|Left Footrest Stud|XL, XLCH, XLS|
|42449-80|1980-1990|Stud|Left Footrest / Cover \\ and Exhaust Stud|Sportsters|
|50806-61P|1954-E1972|Bolt|Rear Footrest Bolt|KH, XL, XLH, XLCH|
|50970-52|1952-E1981|Shoulder Bolt|Rear Footrest Support Bolt|K Models, Sportsters|
|52680-52|1952-1967|Stud|Footrest Bracket Stud|K Models, XL, XLH|
|:::|1958-1969|:::|:::|XLCH|
===== Kickstand =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1760|1952-E1984|#10-24 x 3/8" Flat Head Screw|Jiffy Stand \\ Mounting Pin Screw|K Models, Sportsters|
|:::|:::|#10-32 x 3/8" Flat Head Screw ((1955-1965 Sportster and KH Parts Catalog 99451-65 pg 51))|:::|:::|
|:::|Thread pitch discrepancy in parts books. Corrected in '76 parts catalog supplement.||||
|1760B|1954-E1984|#10-32 x 3/8" Countersunk Head Screw|Jiffy Stand Screw|KH, Sportsters|
|:::|:::|#10-24 x 3/8" Countersunk Head Screw|:::|:::|
|:::|Discrepancy in the parts books on thread pitch. Corrected in '76 parts catalog supplement.||||
|2882W|1985-1988|Bolt|Jiffy Stand Bolt|Sportsters|
|3518|L1984|5/16" x 24 x 1" Flanged Head Bolt|Jiffy Stand Bolt|XL, XLS, XLX|
|3787|L1984-1990|1/4" x 20 x 3/4 " Hex Head Bolt|Jiffy Stand Cushion Bolt|Sportsters|
|4337W|1957-1978|3/8" x 24 x 1-1/4" Hex Head Bolt \\ (grade 5, zinc, NF)|Center Stand \\ Mounting Bracket Bolt|XL, XLH, XLCH|
===== Windshield =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|1202|1953-1957|#10-32 x 1/2" Fillister Head Screw|Windshield Apron Support Screw|K Models, XL|
|:::|1964- |#10-32 x 1/2" Phillips Head Screw|Windshield Center Brace Screw \\ Paired w/ Winter Windshield Kit|1954-up KH, Sportsters|
|1202W|1954-- |#10-32 x 1/2" Fillister Head Screw \\ (Replaced 1202 in 1966)|Windshield T-nut Screw|KH, Sportsters|
|1307|1954-1978|#10-32 x 1/2" Posidriv \\ Fillister Head Screw| |KH, XL, XLH, XLCH|
|2663|1952- |#10-32 x 1/4" Round Head Screw|Windshield Screw|K Models, Sportsters|
|2663B|1954-1962|#10-32 x 1/4" Round Head Screw|Windshield Apron Support Screw|KH, XL, XLH|
|2725|1952-1978|#12-24 x 17/32" Recessed \\ Truss Head Screw|Windshield Bracket Screw|K Models, Sportsters|
|:::|1962-1978|:::|Compact Windshield Brace Screw|XLH, XLCH|
|2725|1979-1981|#12-24 x 1/2" Truss Head Screw|Windshield Trim Screw|XL, XLCH, XLS|
|2726|1952-1978|#12-24 x 21/32" \\ Recessed Truss Head Screw|Lower Windshield Bracket Screw|K Models, Sportsters|
|:::|1962-1978|:::|Compact Windshield Brace Screw|XLH, XLCH|
|2728|1952-1978|#12-24 x 25/32" \\ Recessed Truss Head Screw|Windshield Bracket Screw|K Models, Sportsters|
|:::|1962-1976|:::|Compact Windshield Brace Screw|XLH, XLCH|
|2728|1979-1981|#12-24 x 3/4" Truss Head Screw|Windshield Trim Screw|XL, XLCH, XLS|
|3953W|1952-1981 \\ 1959-1979|5/16" x 24 x 1/2" Hex Head Bolt \\ (NF, Grade 5, Cadmium)|Upper Windshield Bracket Bolt|K Models, XL, XLH, XLS \\ XLCH|
|:::|1962-1978|:::|Compact Windshield \\ Fork Bracket Screw|XLH, XLCH|
|3974 \\ 3974HW|1952-1978 \\ 1959-1978|5/16" x 24 x 3/4" Hex Head Bolt|Lower Windshield Bracket Bolt|K Models, XLH \\ XLCH|
|3996|1962-1981|5/16" x 24 x 7/8" Hex Head Bolt|Compact Winshield Fork Bracket Bolt|XLH, XLCH, XLS|
|9965|1953-1978|Cable Clip|Winter Windshield Apron Clip|K Models, Sportsters|
===== License Plate =====
^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&850|}}|||||
|HD Part#|Year(s) \\ Available|Description|Uses|Models|
|2765|1955- \\ 1959- |1/4" x 20 x 5/8" Round Head Screw|Liscense Plate Screw|KH, XL, XLH \\ XLCH|
|2765B|1955- \\ 1959- |1/4" x 20 x 5/8" Round Head Screw|License Plate Support Screw|KN, XL, XLH \\ XLCH|
|2774|L1973-1990|1/4" x 20 x 5/8" Pozidriv \\ Pan Head Screw|License Plate Bracket Screw|Sportsters|
|5403B|1980-1990|1/4" x 20 x 1/2" Hex Head \\ Carriage Bolt|License Plate Clamp Bolt|Sportsters|
|60002-55|1955-1973 \\ 1959-1973 \\ 1976-1979|Bolt|License Plate Bracket Clamp Bolt|KH, XL, XLH \\ XLCH \\ XLH, XLCH|
\\
[[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]