[[:techtalk:menu|{{ :techtalk:gototechnicalmenu.jpg|}}]] ====== IH: Engine Mechanicals - Sub-01E ====== ====== Ironhead Gearcase/Cam Cover Pics and Information ====== [[techtalk:ih:engmech01g|Click Here]] to go the Ironhead Gearcase/Cam Cover Removal and Installation page in the Sportsterpedia for fastener lists and gaskets. \\ ====== Gearcase / Cam Cover Parts List ====== All part numbers were gathered from period specific Sportster parts catalogs from 1957-1985 including supplement and updated catalogs. \\ ^{{techtalk:miscres:instruction_sheet_header_4.png?nolink&803|}}||||| |Year Model|Cam / Gearcase Cover \\ Part Number|Casting Number|Gasket|Shifter \\ Shaft \\ Bushing| |1952-1956 K Models|25200-52|25202-52|25224-52| | Notes:|Replaced with 25200-52A in 1963. |||| |1957-1962 XL/XLH/XLCH|25200-57|25202-52A|25224-52| | Notes:|Aluminum cover with single horizontal bar and square rear corner (not cut out). \\ Uses generator "daisy wheel" oil deflector w/ sliding separator bushing/spring in cover \\ Replaced by 25200-63A in 1968. |||| |1963-1966 XLH \\ 1963-1967 XLCH|25200-63|25202-52A|25224-52| | Notes:|Aluminum cover with single horizontal bar and square rear corner (not cut out). \\ Uses generator slinger washer oil deflector w/ stationary bushing in cover. \\ Replaced by 25200-63A in 1968. |||| |1967 XLH|25201-67|25202-52A|25224-52| | Notes:|1966 style single bar aluminum cover with rear cutout added around new starter. \\ Oil tank vent (62375-62) added to the rear of the cover. \\ Replaced by 25201-67A in 1969.|||| |1968-1969 XLCH|25200-63A|02-68|25224-52| | Notes:|Aluminum cover with 6 horizontal ribs and square rear corner (not cut out).|||| |1968-1970 XLH|25201-67A|02-68|25224-52| | Notes:|Aluminum cover with 6 horizontal ribs and rear cutout for starter.|||| |1970 XLCH|25200-70|02-68| | | Notes:|Aluminum cover with 6 horizontal ribs and square rear corner (no cut out). \\ Previous boss for magneto redesigned to accept a circuit breaker. \\ Oil tank vent (62375-57) added to the rear of the cover.|||| |1971-1972 XLH \\ 1974 XLH|25201-71|71-25202|25224-52| | Notes:|Polished. |||| |1971-1972 XLCH \\ 1974 XLCH|25200-71|71-25202|25224-52| | Notes:| |||| |1973 XLH|25201-73 \\ black|71-25202|25224-52| | Notes:| |||| |1973 XLCH|25200-73 \\ black|71-25202|25224-52| | Notes:| |||| |1975-1976 XLH|25211-75|71-25202|25224-52| | Notes:|Shifter moved to the left side of the bike in 1975.|||| |1975-1976 XLCH|25205-75|71-25202|25224-52| | Notes:| |||| |1977-1978 XL \\ 1978 XLCH|25201-75|76-25202F|25244-52A| | Notes:| |||| |1977 XLCH|25200-75|76-25202F|25244-52A| | Notes:|Replaced by 25201-75 (1978 parts sup).|||| |1979 XL|25201-79 \\ 25201-79A|79-25202F|25244-52A| | Notes:|Polished. Original cover has a reed type breather valve assembly (26909-79A). \\ Replaced by 25201-79A which has a deeper boss in the nosecone to mount the ignition. \\ Kit includes a spacer (25262-80) to extend ignition to original location. \\ Rubber plug (25221-77) installed in 1979-E1981 cover.|||| |1979 XLCH|25200-79|79-25202|25244-52A| | Notes:|Polished. Original cover has a reed type breather valve assembly (26909-79A). \\ Replaced by 25200-79A which has a deeper boss in the nosecone to mount the ignition. \\ Kit includes a spacer (25262-80) to extend ignition to original location.|||| |1979 XLS|25205-79 \\ 25205-79A|79-25202|25244-52A| | Notes:|Gray. Replaced by 25205-79A which has a deeper boss in the nosecone to mount the ignition. \\ Kit includes a spacer (25262-80) to extend ignition to original location.|||| |1980 XL|25208-80 \\ 25201-79A|80-25222|25244-52A| | Notes:|Polished|||| |1980 XLS|25209-80|80-25222|25244-52A| | Notes:|-80 parts book says, polished. -81 book says black.|||| |E1981 XL|25227-81|81-25223|25244-52A| | Notes:|Polished. Angle cut upper feed galley slot. No pins in cam bushings.|||| |E1981 XLS|25229-81|81-25223|25244-52A| | Notes:|Black. Angle cut upper feed galley slot.|||| |L1981-1982 XLS|25209-81|25222-81|25263-81| | Notes:|Black. Straight cut upper feed galley slot. No casting for tach drive. No pins in cam bushings. \\ 7/16"-14x1/2" allen hd plug screw (2506) installed thru 1985 in place of rubber plug.|||| |L1981-E1984 XL \\ 1983-E1984 XLS/XLX|25208-81|25222-81|25263-81| | Notes:|Polished. No casting for tach drive. No pins in cam bushings.|||| |1983-1985 XLX|25207-83| |25263-81| | Notes:|Kit w/ aluminum finish. No casting for tach drive.|||| |L1984 XLX|25207-84|25222-84A|25263-81| | Notes:|Aluminum finish. Replaced by 25207-84A (-85A parts book)|||| |L1984 XL/XLS|25208-84|25222-84A|25263-81| | Notes:|Polished. Replaced by 25219-86 (-85A parts book)|||| |1985 XLX|25207-84A|25222-84A|25263-81| | Notes:|Black.|||| |1985 XL/XLS|25208-84A|25222-84A|25263-81| | Notes:|Polished. Replaced by 25219-86 (-85A parts book)|||| ====== Internal Comparisons ====== You can interchange some covers if you are not concerned about the look of a stocker for your year bike (better resale trying to stay stock). ((Monte03 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/52221-cams-cover-interchange#post1084712)) \\ Also be aware that some covers had the round cut out for the electric starter XLH that came out in 1967. \\ You can slap a cover on and wing it, BUT the proper way is to have the cover line reamed when the motor is apart. \\ (so the cam cover and the right case half are a match in tolerances) \\ 52-78 cover had only one breather port at 6:00. ((Dr Dick of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) \\ 79-85 had two. One at 6:00 and one at 10:00. \\ 52-76 uses .625" pinion bushing bore. \\ 77-85 uses .562" pinion bushing bore. \\ | 1952-1956 Cam Cover - casting: 25202-52 ((photo by Dr Dick of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) | 1957-1962 Cam Cover - casting: 25202-52A ((photo by ironheadjunkie of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/132743-oil-line-routing/page2?t=1421916&page=2)) | 1963-1967 Cam Cover - casting: 25202-52A((photo by Dr Dick of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) | |{{:techtalk:ih:engmech:cam_cover_52-56_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ih:engmech:cam_cover_1_25202-52a_by_ironheadjunkie.jpg?direct&300|}}|{{:techtalk:ih:engmech:cam_cover_63-67_by_dr_dick.jpg?direct&300|}}| | 1968-1970 Cam Cover - casting: 02-68 ((photo by Dr Dick of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) | 1971-1976 Cam Cover - casting: 25202-71 ((photo by Dr Dick of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) | 1977-1978 Cam Cover - casting 76-25202F ((photo by DirtyCory of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/127032-getting-this-78-back-to-the-way-it-should-be/page9?t=1297584&page=9)) | |{{:techtalk:ih:engmech:cam_cover_68-70_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ih:engmech:cam_cover_71-76_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ih:engmech:cam_cover_77-78_by_dr_dick.jpg?direct&300|}}| | 1979-1980 Cam Cover - casting: 79-25202 ((photo by Dr Dick of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) | 1981 Cam Cover - casting: 81-25223 ((photo by Scott of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/197215-cam-cover-id-help-please-warning-huge-pics?t=2073823)) | L1984-1985 Cam Cover - casting: 25222-84A ((photo by Dr Dick of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/172350-77-breather-please-view-pics/page2?t=1845601&page=2)) \\ (no date code below casting) | |{{:techtalk:ih:engmech:cam_cover_79-80_by_dr_dick.jpg?direct&300|}}|{{:techtalk:ih:engmech:1981_cam_cover_by_scott.jpg?direct&300|}}|{{:techtalk:ih:engmech:cam_cover_l84-85_by_dr_dick.jpg?direct&300|}}| ====== 1957-1970 Cam Covers ====== 1957 thru 1970 Sportsters had cams designed for an ignition to be mounted on top of the cam cover. ((Monte03 of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/52221-cams-cover-interchange?t=230843)) \\ These cams are not interchangeable with post 1971 motors (what can be called the 'cone' cam cover). \\ Early XLs had XL cams, 1966 thru the 1970s had hotter cams known as P cams. \\ 1970 on had the larger 1-15/16" intake valve with pistons to match (piston had a relief cut into the dome for the larger valve clearance). \\ Optional cams were known as PB cams, a bit more umph than P in the upper mid range. \\ P cams are frequently seen for sale on ebay. \\ When hunting for parts you want to ask, "Pre 1971 or Post 1971" for cams and covers including the sprocket cover. \\ ===== 1957-1962 XL/XLH/XLCH Cover ===== Part number (25200-57). Casting number is (25202-52A). \\ Click on a pic to enlarge: ((photos courtesy of Ebay seller, animalhouse2010, [[https://www.ebay.com/str/animalhouse2010?_trksid=p2047675.l2563|Link to Ebay store:]] )) \\ {{:techtalk:ih:engmech:1957-1962_xl-xlh-xlch_cam_cover_25200-57_by_animalhouse2010_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1957-1962_xl-xlh-xlch_cam_cover_25200-57_by_animalhouse2010_pic2.jpg?direct&300|}} {{:techtalk:ih:engmech:1957-1962_xl-xlh-xlch_cam_cover_25200-57_by_animalhouse2010_pic3.jpg?direct&300|}} \\ {{:techtalk:ih:engmech:1957-1962_xl-xlh-xlch_cam_cover_25200-57_by_animalhouse2010_pic4.jpg?direct&300|}} {{:techtalk:ih:engmech:1957-1962_xl-xlh-xlch_cam_cover_25200-57_by_animalhouse2010_pic5.jpg?direct&300|}} {{:techtalk:ih:engmech:1957-1962_xl-xlh-xlch_cam_cover_25200-57_by_animalhouse2010_pic6.jpg?direct&300|}} \\ ===== 1963-1966 XLH, 1963-1967 XLCH Cover ===== Part Number (25200-63). Casting number is (25202-52A). \\ Click on a pic to expand: ((photo courtesy of Ebay seller, Motorcycle Dreams. [[https://www.ebay.com/str/motorcycledreams|Link to Ebay Store:]] )) \\ {{:techtalk:ih:engmech:1963-1966_xlh_1963-1967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1963-1966_xlh_1963-1967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic2.jpg?direct&300|}} {{:techtalk:ih:engmech:1963-1966_xlh_1963-1967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic3.jpg?direct&300|}} \\ {{:techtalk:ih:engmech:1963-1966_xlh_1963-1967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic4.jpg?direct&300|}} {{:techtalk:ih:engmech:1963-1966_xlh_1963-1967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic5.jpg?direct&300|}} {{:techtalk:ih:engmech:1963-1966_xlh_1963-1967_xlch_cam_cover_25200-63_by_motorcycle_dreams_pic6.jpg?direct&300|}} \\ ===== 1967 XLH Cover ===== Part number (25201-67). Casting number (25202-52A). \\ Same as 1967 XLCH but has the cut-out for electric start. \\ {{:techtalk:ih:engmech:1967_xlh_cam_cover_pic1_by_market406.jpg?direct&300|}} ((photo courtesy of Ebay seller, market406. [[https://www.ebay.com/sch/market406/m.html?_nkw=&_armrs=1&_ipg=&_from=|Link to Items for Sale page]] )) {{:techtalk:ih:engmech:1967_xlh_cam_cover_pic3_by_market406.jpg?direct&300|}} ((photo courtesy of Ebay seller, market406. [[https://www.ebay.com/sch/market406/m.html?_nkw=&_armrs=1&_ipg=&_from=|Link to Items for Sale page]] )) \\ ===== 1968-1969 XLCH Cover ===== Cover part number (25200-63A). Casting number is (02-68). \\ The oil tank is still vented to the fitting at the top of the right case behind the rear cylinder. \\ Looks similar to the 68 H cover with exceptions. \\ The XLCH cover has a squared (uncut) rear corner, no 90° fitting on back and the ignition boss on top is set up to accept a magneto. \\ Click on any pic to enlarge: ((photos courtesy of Brewer's Performance Inc. in Laura, Ohio [[http://www.brewersperformance.com/|Link to website]] )) \\ {{:techtalk:ih:engmech:1968-1969_xlch_cam_cover_25200-63_pic1_by_shopanuck.jpg?direct&300|}} {{:techtalk:ih:engmech:1968-1969_xlch_cam_cover_25200-63_pic2_by_shopanuck.jpg?direct&300|}} \\ {{:techtalk:ih:engmech:1968-1969_xlch_cam_cover_25200-63_pic3_by_shopanuck.jpg?direct&300|}} {{:techtalk:ih:engmech:1968-1969_xlch_cam_cover_25200-63_pic4_by_shopanuck.jpg?direct&300|}} \\ ===== 1968-1970 XLH Cover ===== Cover part number (25201-67A). Casting number is (02-68). Top rear corner is cut out for the electric starter. \\ The oil tank is vented to the cam chest at a 90° fitting on the back of the cam cover. \\ 1968-1969 covers came with oil tank vent fitting (62375-62). \\ 1970 XLH covers came with oil tank fitting (62375-57). \\ Both fittings are 1/8"-27 NPT to 1/4" hose barb 90° elbows. \\ {{:techtalk:ih:engmech:1968-1970_xlh_cam_cover_25201-67a_pic1_by_flashback_inc.jpg?direct&300|}} ((photo courtesy of Flashback Enterprises in Imlay City, MI, [[https://www.ebay.com/str/flashbackenterprisesinc?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] )) {{:techtalk:ih:engmech:1968-1970_xlh_cam_cover_25201-67a_pic2_by_flashback_inc.jpg?direct&300|}} ((photo courtesy of Flashback Enterprises in Imlay City, MI, [[https://www.ebay.com/str/flashbackenterprisesinc?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] )) \\ {{:techtalk:ih:engmech:1968-1970_xlh_cam_cover_25201-67a_pic1_by_cyclewarehouse.jpg?direct&300|}} ((photo courtesy of Ebay seller, cyclewarehouse. [[https://www.ebay.com/sch/cyclewarehouse/m.html?_nkw=&_armrs=1&_ipg=&_from=|Link to Items for Sale]] )) {{:techtalk:ih:engmech:1968-1970_xlh_cam_cover_25201-67a_pic3_by_flashback_inc.jpg?direct&300|}} ((photo courtesy of Flashback Enterprises in Imlay City, MI, [[https://www.ebay.com/str/flashbackenterprisesinc?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] )) \\ ===== 1970 XLCH Cover ===== Cover part number (25200-70). Casting number (02-68). TOP REAR IS NOT CUT for electric start. \\ 1970-up XLH and XLCH motors all now vent the oil tank air space to the cam chest at a 90° fitting on the back of the cam cover. \\ The previous year's vent location on the top of the rear engine case was deleted for XLCH. \\ The fitting (62375-57) is a 1/8"-27 NPT to 1/4" hose barb 90° elbow. \\ Click on a pic to enlarge: ((pics by Scott of the XLFORUM https://www.xlforum.net/forum/sportster-motorcycle-forum/sportster-motorcycle-era-specific-and-model-specific/ironhead-sportster-motorcycle-talk-1957-1985/197215-cam-cover-id-help-please-warning-huge-pics?t=2073823)) \\ {{:techtalk:ih:engmech:1970_xlch_cam_cover_25200-70_pic1_by_scott.jpg?direct&300|}} {{:techtalk:ih:engmech:1970_xlch_cam_cover_25200-70_pic2_by_scott.jpg?direct&300|}} {{:techtalk:ih:engmech:1970_xlch_cam_cover_25200-70_pic3_by_scott.jpg?direct&300|}} \\ ====== 1971-1974 Cam Covers ====== ===== 1971-1972, 1974 XLH Cover ===== Cover part number (25200-71). Casting number (71-25202). \\ Gasket (25224-52). Updated gasket (25224-52A). \\ Fasteners: (8) cover screws, (2) generator mounting bolts and (2) solid dowel pins (used at front and rear of cover). \\ [[techtalk:ih:engmech01g#cam_cover_fastener_list|Click Here]] to see full fastener list. \\ The difference in this cover from the 1973 XLH cover is this one is polished and the 1973 cover is black. \\ Click on a pic to enlarge: ((photos courtesy of Ebay seller, 57harleyrider. [[https://www.ebay.com/str/57harleyrider|Link to Ebay Store]] )) \\ {{:techtalk:ih:engmech:1971-1972_xlh_1974_xlh_cam_cover_25201-71_by_57harleyrider_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1971-1972_xlh_1974_xlh_cam_cover_25201-71_by_57harleyrider_pic2.jpg?direct&300|}} {{:techtalk:ih:engmech:1971-1972_xlh_1974_xlh_cam_cover_25201-71_by_57harleyrider_pic3.jpg?direct&300|}} \\ {{:techtalk:ih:engmech:1971-1972_xlh_1974_xlh_cam_cover_25201-71_by_57harleyrider_pic4.jpg?direct&300|}} {{:techtalk:ih:engmech:1971-1972_xlh_1974_xlh_cam_cover_25201-71_by_57harleyrider_pic5.jpg?direct&300|}} {{:techtalk:ih:engmech:1971-1972_xlh_1974_xlh_cam_cover_25201-71_by_57harleyrider_pic6.jpg?direct&300|}} \\ ====== 1975-1976 Cam Covers ====== ===== 1975-1976 XLH Cover ===== Cover part number (25211-75). Casting number (71-25202). \\ Gasket (25224-52A). \\ Fasteners: (8) cover screws, (2) generator mounting bolts and (2) solid dowel pins (used at front and rear of cover). \\ [[techtalk:ih:engmech01g#cam_cover_fastener_list|Click Here]] to see full fastener list. \\ ===== 1975-1976 XLCH Cover ===== Cover part number (25205-75). Casting number (71-25202). \\ Gasket (25224-52A). \\ Fasteners: (8) cover screws, (2) generator mounting bolts and (2) solid dowel pins (used at front and rear of cover). \\ [[techtalk:ih:engmech01g#cam_cover_fastener_list|Click Here]] to see full fastener list. \\ Click on a pic to enlarge: ((photo courtesy of Ebay seller, gnarlydavidson1. [[https://www.ebay.com/sch/gnarlydavidson1/m.html?item=164269655258&rt=nc&nma=true&nordt=true&orig_cvip=true&si=HqcoQgHNj7TAtnE2%252BX5d6I6LD7A%253D&hash=item263f3c04da%3Ag%3AIDEAAOSw4CRe-35v&vxp=mtr&_trksid=p2047675.l2562|Link to Items for Sale page]] )) \\ {{:techtalk:ih:engmech:1975-1976_xlch_cam_cover_25205-75_by_gnarlydavidson1_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1975-1976_xlch_cam_cover_25205-75_by_gnarlydavidson1_pic2.jpg?direct&300|}} {{:techtalk:ih:engmech:1975-1976_xlch_cam_cover_25205-75_by_gnarlydavidson1_pic3.jpg?direct&300|}} \\ ====== 1977-1978 Cam Covers ====== ===== 1977-1978 XLH Cover ===== HD Part number (25201-75). Casting number (76-25202F). \\ Gasket: (25224-52A). \\ Fasteners: (8) cover screws, (2) generator mounting bolts and (1) front solid dowel pin (rear dowel hole in cover drilled but not in case). \\ [[techtalk:ih:engmech01g#cam_cover_fastener_list|Click Here]] to see full fastener list. \\ Click on a pic to enlarge: ((photos courtesy of NitroFrankie Go-Fast HD, [[https://www.ebay.com/sch/m.html?item=194837126341&_ssn=ct_kustoms&_ipg=200&rt=nc|Ebay Items for Sale Page]] )) \\ {{:techtalk:ih:engmech:1977-1978_xl_cam_cover_25201-75_by_nitrofrankie_go-fast_hd_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1977-1978_xl_cam_cover_25201-75_by_nitrofrankie_go-fast_hd_pic2.jpg?direct&300|}} {{:techtalk:ih:engmech:1977-1978_xl_cam_cover_25201-75_by_nitrofrankie_go-fast_hd_pic3.jpg?direct&300|}} \\ {{:techtalk:ih:engmech:1977-1978_xl_cam_cover_25201-75_by_nitrofrankie_go-fast_hd_pic4.jpg?direct&300|}} {{:techtalk:ih:engmech:1977-1978_xl_cam_cover_25201-75_by_nitrofrankie_go-fast_hd_pic5.jpg?direct&300|}} {{:techtalk:ih:engmech:1977-1978_xl_cam_cover_25201-75_by_nitrofrankie_go-fast_hd_pic6.jpg?direct&300|}} \\ ====== 1979-E1984 Cam Covers ====== === Starter Cutout on Top Rear === L1976-1980 Sportsters use a Prestolite starter which required a section of the top rear corner of the cam cover to be factory removed for clearance. \\ 1981-1985 Sportsters use a Nippon Denso starter which doesn't require the cam cover clearance thus the corner is squared off (uncut). \\ === Breather Valves === 1979-E1982 production cam covers were installed with a reed type breather valve (26909-79). \\ In L1982, a new rubber umbrella type breather valve was used in production covers. \\ Breather valve kit (26909-79A) was then introduced to adapt 1979-E1982 covers with the new umbrella valve system. \\ So you may find used 1979-E1982 covers with the umbrella valves instead. \\ [[techtalk:ih:engmech07#e1982_breather_valve|Click Here]] for more information on breather valves. \\ 1979-1981 Sportsters use a 1-5/8" slinger washer (31067-63). \\ 1982-E1984 Sportsters use a 1-3/4" slinger washer (31066-82) to accommodate the larger crankcase breather valve. \\ L1984-1985 Sportsters don't use a generator or slinger washer. \\ === Breather Vents === 1979 is the first year a hole was drilled and tapped in top front of the cam cover for the breather vent to connect up to the air cleaner housing \\ The previous location on the front bottom of the cam cover for the breather tube was plugged off with a 1/8"x27 plug and the tube deleted. \\ A rubber hose was now piped from the top of the cam cover to the A/C (keeping the breather line from crossing the cover from the bottom). \\ This design was used from 1979-1990. \\ Some have removed the lower plug to add a second breather to atmosphere although the reviews for that mod vary. \\ [[techtalk:ref:engmech05i|Click Here]] for more information on that mod in the Sportsterpedia. \\ === 1979-1980 Ignition Changes === 1979 models got a new Prestolite breakerless electronic ignition module in the cam cover nosecone. \\ 1980 models changed to a Magnavox ignition system using different parts in the cam cover nosecone and the module was moved out of the nosecone. \\ This resulted in the "pocket" in the newer cover nosecone for 1980 models getting a little deeper. \\ Since the 1980 cover was also sold as replacement for 1979 models, the deeper pocket wouldn't work for 1979 ignitions. \\ So a spacer (25262-80) was included with the 1979-1980 replacement cover to extend 1979 ignitions to original location when using the newer cover. \\ The replacement cover part number is (25201-79A) which includes the spacer. \\ | 1979 and 1980 nosecone comparison ((1979-1980 Sportster Nosecone Design Change Composite from [[https://www.ebay.com/sch/m.html?item=194837126341&_ssn=ct_kustoms&_ipg=200&rt=nc|NitroFrankie Go-Fast HD]] and [[https://www.ebay.com/str/cos0608|WheatStateParts]] )) | Here is the spacer from the kit. ((photo courtesy of Royal Motorworks Citroen Parts Plus, [[https://www.ebay.com/str/royalmotorworkscitroenpartsplus?_trksid=p2047675.m3561.l2563|Link to Ebay Store]] )) | |{{:techtalk:ih:engmech:1979-1980_sportster_nosecone_design_change_composite_from_nitrofrankie_go-fast_hd_and_wheatstateparts.jpg?direct&300|}}|{{:techtalk:ih:engmech:1979_sportster_cam_cover_spacer_25262-80_by_royal_motorworks_citroen_parts_plus.jpg?direct&300|}}| === L1981 Production Changes === **L1981-E1982 Gearcase/Cam Cover/Gasket Changes**: \\ {{ pdf-bulletin:tsb0841.pdf |Click Here}} to download TSB M-841. \\ Cases: \\ L1981-E1982 engines may have one of two different types of gear case cover and crankcase set combinations. \\ Old style cases have a slanted slot for an upper oil feed galley to the lifters and no rear dowel pin (or bolt) to attach the cover. \\ New style cases have a large boss around the upper feed galley with a single hole (no slot) for a feed oil galley to the lifters. \\ New style cases also have an extra mounting screw hole added to the top rear corner of the cover mounting boss. \\ **Cam Cover Gasket**: \\ Gasket (25224-52A) originally (1977) had a single hole in the top center to transfer oil from the gasket to the upper case galley. \\ Along with 1979 case changes, the hole was slotted at an angle and along with L1981 case changes, the gasket was redesigned. \\ Old style gasket (25224-52A) can only be used with the old style covers, XLH (25227-81) and XLS (25229-81). \\ New style gasket (25263-81) can only be used with the new style covers, XLH (25208-81) and XLS (25209-81). \\ **Cam Cover**: \\ Old style cam covers can be used on new style cases along with the old style gasket. \\ New style cam covers cannot be used on old style cases. \\ ===== 1979 XLH Cover ===== HD Part number (25201-79 ). Casting number (79-25202F). \\ Finish: Polished. \\ Gasket: (25224-52A). \\ Fasteners: (8) cover screws, (2) generator mounting bolts and (1) front solid dowel pin (rear dowel hole in cover drilled but not in case). \\ [[techtalk:ih:engmech01g#cam_cover_fastener_list|Click Here]] to see full fastener list. \\ Replacement cover kit (25201-79A) comes with the 1980 cover and a spacer ring (25262-80) for the ignition module. \\ See "1979-1980 Ignition Changes" above. \\ Below is the original cover. Click on a pic to enlarge: \\ | 1979 XLH cam cover ((photo courtesy of NitroFrankie Go-Fast HD, [[https://www.ebay.com/sch/m.html?item=194837126341&_ssn=ct_kustoms&_ipg=200&rt=nc|Ebay Items for Sale Page]] )) ||| |{{:techtalk:ih:engmech:1979_xlh_cam_cover_25201-79_by_nitrofrankie_go-fast_hd_pic1.jpg?direct&300|}}|{{:techtalk:ih:engmech:1979_xlh_cam_cover_25201-79_by_nitrofrankie_go-fast_hd_pic2.jpg?direct&300|}}|{{:techtalk:ih:engmech:1979_xlh_cam_cover_25201-79_by_nitrofrankie_go-fast_hd_pic3.jpg?direct&300|}}| | 1979 XLH cam cover ((photo courtesy of NitroFrankie Go-Fast HD, [[https://www.ebay.com/sch/m.html?item=194837126341&_ssn=ct_kustoms&_ipg=200&rt=nc|Ebay Items for Sale Page]] )) || First year for top breather fitting ((photo courtesy of Ebay seller, gnarlydavidson1. [[https://www.ebay.com/sch/gnarlydavidson1/m.html?item=164269655258&rt=nc&nma=true&nordt=true&orig_cvip=true&si=HqcoQgHNj7TAtnE2%252BX5d6I6LD7A%253D&hash=item263f3c04da%3Ag%3AIDEAAOSw4CRe-35v&vxp=mtr&_trksid=p2047675.l2562|Link to Items for Sale page]] )) | |{{:techtalk:ih:engmech:1979_xlh_cam_cover_25201-79_by_nitrofrankie_go-fast_hd_pic4.jpg?direct&300|}}|{{:techtalk:ih:engmech:1979_xlh_cam_cover_25201-79_by_nitrofrankie_go-fast_hd_pic5.jpg?direct&300|}}|{{:techtalk:ih:engmech:1979_xlh_cam_cover_25201-79_by_gnarlydavidson1.jpg?direct&300|}}| ===== 1979 XLS Cover ===== HD Part number (25205-79 ). Casting number (79-25202F). \\ Finish: Gray. \\ Gasket: (25224-52A). \\ Fasteners: (8) cover screws, (2) generator mounting bolts and (1) front solid dowel pin (rear dowel hole in cover drilled but not in case). \\ [[techtalk:ih:engmech01g#cam_cover_fastener_list|Click Here]] to see full fastener list. \\ Replacement cover kit (25201-79A) comes with the 1980 cover and a spacer ring (25262-80) for the ignition module. \\ See "1979-1980 Ignition Changes" above. \\ Below is the original cover. It's the same as the original 1979 XLH cover except for the finish. \\ Click on a pic to enlarge: ((photos courtesy of Ebay seller, Harley-Davidson Parts Accessories. [[https://www.ebay.com/str/harleydavidsonpartsaccessories|Link to Ebay Store]] )) \\ {{:techtalk:ih:engmech:1979_xls_cam_cover_25205-79_by_harley-davidson_parts_accessories_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1979_xls_cam_cover_25205-79_by_harley-davidson_parts_accessories_pic2.jpg?direct&300|}} {{:techtalk:ih:engmech:1979_xls_cam_cover_25205-79_by_harley-davidson_parts_accessories_pic3.jpg?direct&300|}} \\ {{:techtalk:ih:engmech:1979_xls_cam_cover_25205-79_by_harley-davidson_parts_accessories_pic4.jpg?direct&300|}} {{:techtalk:ih:engmech:1979_xls_cam_cover_25205-79_by_harley-davidson_parts_accessories_pic5.jpg?direct&300|}} {{:techtalk:ih:engmech:1979_xls_cam_cover_25205-79_by_harley-davidson_parts_accessories_pic6.jpg?direct&300|}} \\ ===== 1980 XLH Cover ===== Part number for cover (25208-80). Casting number (80-25222). \\ Gasket: (25224-52A). \\ Fasteners: (8) cover screws, (2) generator mounting bolts and (1) front solid dowel pin (rear dowel hole in cover drilled but not in case). \\ [[techtalk:ih:engmech01g#cam_cover_fastener_list|Click Here]] to see full fastener list. \\ This cover was also sold as a replacement cover for 1979 models with an added spacer ring for 1979 ignitions. \\ Part number for the replacement kit for 1979-1980 models is (25201-79A). \\ Click on a pic to enlarge: ((photos courtesy of Ebay seller, WheatStateParts. [[https://www.ebay.com/str/cos0608|Link to Ebay Store]] )) \\ {{:techtalk:ih:engmech:1980_xlh_cam_cover_25208-80_by_wheatstateparts_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1980_xlh_cam_cover_25208-80_by_wheatstateparts_pic2.jpg?direct&300|}} {{:techtalk:ih:engmech:1980_xlh_cam_cover_25208-80_by_wheatstateparts_pic3.jpg?direct&300|}} \\ {{:techtalk:ih:engmech:1980_xlh_cam_cover_25208-80_by_wheatstateparts_pic4.jpg?direct&300|}} {{:techtalk:ih:engmech:1980_xlh_cam_cover_25208-80_by_wheatstateparts_pic5.jpg?direct&300|}} {{:techtalk:ih:engmech:1980_xlh_cam_cover_25208-80_by_wheatstateparts_pic6.jpg?direct&300|}} \\ ===== E1981 XLS Cover ===== Part number (25229-81). Casting number (81-25223). Tach drive casting still there but the hole wasn't drilled for the drive unit. \\ Gasket: Must use gasket (25224-52A). \\ Fasteners: (8) cover screws, (2) generator mounting bolts and (1) front solid dowel pin (rear dowel hole in cover drilled but not in case). \\ [[techtalk:ih:engmech01g#cam_cover_fastener_list|Click Here]] to see full fastener list. \\ Click on a pic to enlarge: ((photos courtesy of NitroFrankie Go-Fast HD, [[https://www.ebay.com/sch/m.html?item=194837126341&_ssn=ct_kustoms&_ipg=200&rt=nc|Ebay Items for Sale Page]] )) \\ {{:techtalk:ih:engmech:1981e_xls_cam_cover_-_black_-_25229-81_by_nitrofrankie_go-fast_hd_pic1.jpg?direct&300|}} \\ {{:techtalk:ih:engmech:1981e_xls_cam_cover_-_black_-_25229-81_by_nitrofrankie_go-fast_hd_pic2.jpg?direct&300|}} {{:techtalk:ih:engmech:1981e_xls_cam_cover_-_black_-_25229-81_by_nitrofrankie_go-fast_hd_pic3.jpg?direct&300|}} {{:techtalk:ih:engmech:1981e_xls_cam_cover_-_black_-_25229-81_by_nitrofrankie_go-fast_hd_pic4.jpg?direct&300|}} \\ ====== L1984-1985 Cam Covers ====== ===== 1985 XL/XLS Cover ===== Part number (25208-84A). Casting number (25222-84A). Gasket: (25263-81). \\ Fasteners: (9) cover screws, (2) oil filter housing bolts, (1) front solid dowel pin in gearcase and (1) rear dowel pin in case near transmission. \\ [[techtalk:ih:engmech01g#cam_cover_fastener_list|Click Here]] to see full fastener list. \\ This cover is almost identical to the 1986-1990 Sportster cover. \\ In fact, the -85A parts book lists the 1986 cover for replacement on L1984 XL/XLS models. \\ So they are compatible. The main visual difference is in the casting numbers. \\ 1985 casting# (25222-84A) is a standalone number cast in the front, not far from the breather valve with no circle date code. \\ 1986-1990 casting# (25222-84A) is in the same spot but all have a circle date code under the casting number (date of casting is in the circle). \\ Click on a pic to enlarge: ((photo courtesy of NitroFrankie Go-Fast HD, [[https://www.ebay.com/sch/m.html?item=194837126341&_ssn=ct_kustoms&_ipg=200&rt=nc|Ebay Items for Sale Page]] )) \\ {{:techtalk:ih:engmech:1985_xl-xls_cam_cover_25208-84a_by_nitrofrankie_go-fast_hd_pic1.jpg?direct&300|}} {{:techtalk:ih:engmech:1985_xl-xls_cam_cover_25208-84a_by_nitrofrankie_go-fast_hd_pic2.jpg?direct&300|}} {{:techtalk:ih:engmech:1985_xl-xls_cam_cover_25208-84a_by_nitrofrankie_go-fast_hd_pic3.jpg?direct&300|}} \\ | L1984-1985 cover casting# (25222-84A) ((photo courtesy of NitroFrankie Go-Fast HD, [[https://www.ebay.com/sch/m.html?item=194837126341&_ssn=ct_kustoms&_ipg=200&rt=nc|Ebay Items for Sale Page]] )) | 1986-1990 cover casting# (25222-84A) ((photo courtesy of DeadpartsMC, [[https://www.ebay.com/str/deadpartsmc|Link to Ebay Store]] )) | |{{:techtalk:ih:engmech:1985_xl-xls_cam_cover_25208-84a_by_nitrofrankie_go-fast_hd_pic4.jpg?direct&300|}}|{{:techtalk:evo:engmech:1986-1990_sportster_cam_cover_25219-86_by_deadpartsmc_pic5.jpg?direct&300|}}| \\ [[:techtalk:menu|{{:techtalk:gototechnicalmenu.jpg|}}]]